emu10k1 - interrupt storm?
Hello and sorry for replying late,
I did experienced same problems with emu10k1 on 2.4.8 (as is in Mandrake 8.1).
After modprobing emu10k1, interrupts per second (as reported by vmstat) start to increase and in few minutes they were as high as 70000 per second. rmmod-ing emu10k1 caused number of interrupts per second to slowly decrease.
Following setting affected this:
In BIOS setup, PCI options:
Interrupts triggered by
1, edge
2, level
value 'edge' causes problems,
value 'level' makes thing work without problems.
If you are experiencing problems with this, set to 'level'.
Jakub Travnik
jabber://[email protected]
----Replied message follows----
From: Zlatko Calusic ([email protected])
Date: Sun Dec 09 2001 - 16:54:03 EST
Quoted 6 lines · Rui Sousa
The current emu10k1 driver uses a hardware clock to generate periodic interrupts. These apparently ran at the wrong rate in some Alpha machines. It's possible that the same problem occur now with more recent i386 machines.
Hi!
Sorry to quote a really old email. :)
I'm currently investigating why is my emu10k1 doing so much interrupts. They are so frequent that they usually show on a kernel profile report on the top, no matter what I've been doing with the poor machine (interrupts are there even if I'm not using my Soundblaster live).
Kernel is the most recent 2.5.x. dmesg says:
Creative EMU10K1 PCI Audio Driver, version 0.16, 16:17:32 Dec 9 2001
emu10k1: EMU10K1 rev 6 model 0x8027 found, IO at 0xc400-0xc41f, IRQ 10ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
This is my /proc/interrupts:
CPU0 CPU1
0: 423348 425806 IO-APIC-edge timer
1: 13674 13371 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 2 1 IO-APIC-edge rtc
10: 5956299 5956064 IO-APIC-level EMU10K1 <=========== 11: 19803 20033 IO-APIC-level ide2
12: 104203 101822 IO-APIC-edge PS/2 Mouse
14: 4356 4285 IO-APIC-edge ide0
15: 7 9 IO-APIC-edge ide1
NMI: 0 0
LOC: 849167 849165
ERR: 2
MIS: 0
Yes, this is a SMP machine, but I don't know why would that make any difference. As you can see, number of emu10k1 interrupts is enormous (I also tried noapic, no changes).
procinfo -d quickly shows that emu10k1 is generating ~1412 interrupts per second (7060/2).
irq 0: 500 timer irq 10: 7060 EMU10K1
irq 1: 1 keyboard irq 11: 10 ide2
irq 2: 0 cascade [4] irq 12: 164 PS/2 Mouse
irq 3: 0 irq 14: 2 ide0
irq 4: 0 irq 15: 0 ide1
irq 8: 0 rtc
Is that the periodic hardware interrupt you're talking about, and why are there so many interrupts? Is there a way to stop that storm?
Regards,
Signature · 2 lines
Zlatko -
Quoted 8 lines · Jakub Travnik
Hello and sorry for replying late,
I did experienced same problems with emu10k1 on 2.4.8 (as is in Mandrake 8.1).
After modprobing emu10k1, interrupts per second (as reported by vmstat) start to increase and in few minutes they were as high as 70000 per second. rmmod-ing emu10k1 caused number of interrupts per second to slowly decrease.
Quoted 6 lines
Following setting affected this:
In BIOS setup, PCI options:
Interrupts triggered by
1, edge
2, level
Unfortunately I don't have that setting in my BIOS.
Quoted 4 lines
value 'edge' causes problems,
value 'level' makes thing work without problems.
But anyway, emu10k1 on irq 5 already uses level type:
5: 5193 5183 IO-APIC-level EMU10K1
Quoted 2 lines
If you are experiencing problems with this, set to 'level'.
Eventually, I forced esd to exit after few seconds of inactivity. That way I at least don't have interrupt storms when I don't have any sound output through esd.
Regards,
Signature · 1 line
Zlatko