New IBM IDE drive recognized as 40 GB but is 80 GB

Dear kernel hackers,

This problem is on a:

Linux version 2.4.18-pre3-ac1 ([email protected]) (gcc version 2.96

We have bought a new IDE hard drive:

hdb: IC35L040AVVA07-0, ATA DISK drive

This is wrongly recognized as 40GB (should be 80GB) drive:

====================
ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=3649/255/63, (U)DMA
hdb: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=5005/255/63, UDMA(33)

                       <----> this is wrong

But doing:

[root@apu /root]# cat /proc/ide/hdb/capacity
80418240 <--------------------------------- this is correct
[root@apu /root]#

shows the right capacity.

The CHS counts in dmesg are not the ones physically printed on the drive. However, a kernel command line "hdb=16383/16/63" did not fix the problem and resulted in the same GB count.

mke2fs on a fully allocated /dev/hdb1 shows 40GB to me. Using LVM on the whole drive /dev/hdb same thing, only 40 GB.

What am I doing wrong?

Thanks for your help and a private cc, since I'm no subscriber.

Take Care,

;Martin

Below my kernel config (IDE relevant stuff):

Config:
=====================
[root@apu /root]# grep IDE /root/apukernel/linux/.config # CONFIG_PARIDE is not set
# ATA/IDE/MFM/RLL support
CONFIG_IDE=y
# IDE, ATA and ATAPI Block devices CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_IDECS is not set CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=m CONFIG_BLK_DEV_IDEFLOPPY=m CONFIG_BLK_DEV_IDESCSI=m CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_BLK_DEV_IDEDMA_PCI=y CONFIG_IDEDMA_PCI_AUTO=y CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_IDE_CHIPSETS is not set CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set CONFIG_BLK_DEV_IDE_MODES=y
# Old CD-ROM drivers (not SCSI, not IDE)
# CONFIG_CD_NO_IDESCSI is not set
# CONFIG_INPUT_SIDEWINDER is not set
# CONFIG_VIDEO_DEV is not set
# CONFIG_VIDEO_SELECT is not set
[root@apu /root]#

Thats a 40Gb drive. IC35L[capacity]....