Skip to contentSkip to conversation

Rate Conversion

DISCUSSION Kris Modrak 3 participants 6 messages Jun 27, 2002 – Jul 1, 2002

lore
Share & tools
lore
#0 lore raw

I am writing a PCM application and wish to play a .wav file that has a sampling rate of 8kHz on a hardware setup that only supports sampling frequencies of 44.1 or 48kHz.

Does anyone know how to implement this?

I have tried setting up a rate plugin in my .asoundrc file

pcm.r8 {
type rate # Rate PCM
slave slave_rate8000Hz # Slave name
}

pcm_slave.slave_rate8000Hz {
        pcm "hw:0,0"
        rate 8000
}

But when using this device I am unable to set the rate to 8000 using snd_pcm_hw_params_set_rate_near ();

I tried using the r8 device with aplay (version 0.9.0beta12) and get the following error

Quoted 1 line

aplay -Dr8 s1.wav

Playing WAVE 's1.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono
aplay: set_params:717: Broken configuration for this PCM: no configurations available

I know it is possible to play the file because it works when I play it from a netscape window.

Thanks in advance
Kris Modrak

-------------------------------------------------------
Sponsored by:
ThinkGeek at http://www.ThinkGeek.com/

#1 lore raw
Quoted 5 lines · Kris Modrak

I am writing a PCM application and wish to play a .wav file that has a sampling rate of 8kHz on a hardware setup that only supports sampling frequencies of 44.1 or 48kHz.

Does anyone know how to implement this?

You don't need to do this. Use the 'plughw' device which should do all conversions from you.

Quoted 11 lines

I have tried setting up a rate plugin in my .asoundrc file

pcm.r8 {
type rate # Rate PCM
slave slave_rate8000Hz # Slave name
}

pcm_slave.slave_rate8000Hz {
        pcm "hw:0,0"
        rate 8000

Use 44100 or 48000. It's the rate for the hardware not the source rate.

Jaroslav

-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project http://www.alsa-project.org
SuSE Linux http://www.suse.com

-------------------------------------------------------
Sponsored by:
ThinkGeek at http://www.ThinkGeek.com/

#2 lore raw
Quoted 11 lines · Jaroslav Kysela
Quoted 5 lines · Kris Modrak

I am writing a PCM application and wish to play a .wav file that has a sampling rate of 8kHz on a hardware setup that only supports sampling frequencies of 44.1 or 48kHz.

Does anyone know how to implement this?

You don't need to do this. Use the 'plughw' device which should do all conversions from you.

I am a little confused about your advice. I am not sure how to access the 'plughw' device from my application.

I have a full duplex application that can play a file at 44.1kHz and record at the same rate but I want it to operate at lower sampling frequencies.

I am not sure of how I should be setting up my PCM devices. How do I tell them to convert, say, 8kHz audio data to 44.1kHz audio data so my hardware can play it at the correct speed?

I tried using aplay with plughw to play an 8kHz file and got the following results

Quoted 1 line

aplay -Dplughw s1.wav

Playing WAVE 's1.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono Segmentation fault

However it worked when using a 441.kHz file.

Regards
Kris Modrak

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#3 lore raw
Quoted 5 lines
Quoted 2 lines

You don't need to do this. Use the 'plughw' device which should do all conversions from you.

I am a little confused about your advice. I am not sure how to access the 'plughw' device from my application.

     snd_pcm_open (&handle, "plughw:N,M", ...)

where N and M are the card number and subdevice number. Preferably, this is a string supplied by the user, not hard coded into the application.

Quoted 3 lines

I am not sure of how I should be setting up my PCM devices. How do I tell them to convert, say, 8kHz audio data to 44.1kHz audio data so my hardware can play it at the correct speed?

just as in the few token API examples. using snd_pcm_hw_params_*(). there is no difference setting the parameters no matter what "type" of PCM device you are using.

Quoted 6 lines

I tried using aplay with plughw to play an 8kHz file and got the following results

Quoted 1 line

aplay -Dplughw s1.wav

Playing WAVE 's1.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono Segmentation fault

almost certainly a bug in aplay. i suspect you might be one of the first people to use it for a mono 8kHz file :(

--p

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Caffeinated soap. No kidding.
http://thinkgeek.com/sf

#4 lore raw
Quoted 9 lines · Paul Davis
Quoted 3 lines

I am a little confused about your advice. I am not sure how to access the 'plughw' device from my application.

     snd_pcm_open (&handle, "plughw:N,M", ...)

where N and M are the card number and subdevice number. Preferably, this is a string supplied by the user, not hard coded into the application.

Quoted 7 lines
Quoted 3 lines

I am not sure of how I should be setting up my PCM devices. How do I tell them to convert, say, 8kHz audio data to 44.1kHz audio data so my hardware can play it at the correct speed?

just as in the few token API examples. using snd_pcm_hw_params_*(). there is no difference setting the parameters no matter what "type" of PCM device you are using.

Apart from rates or 44.1 or 48kHz I was unable to find a rate/period size combination that I was able to use with plughw:0,0.

snd_pcm_hw_params_set_period_size () failed for every period size I tried (64, 128, 256, 512, 1024, 2048 and 4096) when I had the rate set to 8, 16 or 32 kHz.

I managed to set the following combinations of hardware parameters:
-22050Hz with period sizes of 2048, 1024, 512, 256, 128 and 64 -11025Hz with period sizes of 1024, 512, 256, 128 and 64

but when I ran my application I encountered the following error

ALSA lib pcm_hw.c:380:(snd_pcm_hw_start) SNDRV_PCM_IOCTL_START failed:
Broken pipe

Does anyone have any further suggestions of things that I could try or why this rate conversion isn't working for me? I am using ALSA 0.9.0beta12 with a Hammerfall Light (RME Digi9636) soundcard.

Kris Modrak

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#5 lore raw
Quoted 2 lines

Apart from rates or 44.1 or 48kHz I was unable to find a rate/period size combination that I was able to use with plughw:0,0.

This is an error in alsa-lib as far as I can tell. its possible to set the rate to 32kHz using the hardware device (for the Hammerfall) and use it without a problem. I wish I could help you with the issue in alsa-lib, but i don't understand it well enough nor do i have the time.

--p

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf