Need contact info for Origin 200
Hello, OSS @ SGI gang--
I need a little help, please! As a result of a company closing, I've received a pair of SGI Origin 200 servers. Unfortunately, since the support contract on them has expired, I can't seem to use any of the support services at www.sgi.com.
I'm just a home experimenter who wants to run the things 'til they die. I'm very pleased with the performance, software, etc., and I'm very familiar with them (as I worked on them 8 hrs / day for a year and a half until the office closed).
The only difficulty is that these things are LOUD! I'd like to find out if there are any temperature monitors inside the thing, and if I can run the fans at a reduced speed, or remove some of the fans to make them reasonable in a home environment. They don't do a lot (as I just do some CPU-intensive stuff on them every once in a while, and very little disk-I/O).
Thus, I'd like to find a contact for simple (but technical) hardware questions like these on the Origin 200. If you guys could send me a friendly contact or two, I'd be very grateful.
(I'm also interested in making the thing dual-boot Irix & Linux, if the Linux port is close to operating... I've also got a pair of Indys that I'm planning on sacrificing to the Linux gods...)
Thanks in advance--
--marco
Quoted 6 lines · Marco C. Mason
The only difficulty is that these things are LOUD! I'd like to find out if there are any temperature monitors inside the thing, and if I can run the fans at a reduced speed, or remove some of the fans to make them reasonable in a home environment. They don't do a lot (as I just do some CPU-intensive stuff on them every once in a while, and very little disk-I/O).
Via the system controller you can set the fan speed. Only the fan speeds n like normal and h like high are supported. If the machine feels like it is hot or one of the fans has failed it'll automatically switch the fan speed to h. If more than one fan fails it'll power off ...
Quoted 3 lines
Thus, I'd like to find a contact for simple (but technical) hardware questions like these on the Origin 200. If you guys could send me a friendly contact or two, I'd be very grateful.
Well, try this list.
Quoted 3 lines
(I'm also interested in making the thing dual-boot Irix & Linux, if the Linux port is close to operating... I've also got a pair of Indys that I'm planning on sacrificing to the Linux gods...)
The Indy port is in reasonable shape; the O200 port has decayed a bit over the past months but as far as time permits I'm working on getting it to run again.
Ralf
They are running at reduced speed unless the temp is over ~90. I can answer most common questions about them.
Nick
Quoted 32 lines · Marco C. Mason
Hello, OSS @ SGI gang--
I need a little help, please! As a result of a company closing, I've received a pair of SGI Origin 200 servers. Unfortunately, since the support contract on them has expired, I can't seem to use any of the support services at www.sgi.com.
I'm just a home experimenter who wants to run the things 'til they die. I'm very pleased with the performance, software, etc., and I'm very familiar with them (as I worked on them 8 hrs / day for a year and a half until the office closed).
The only difficulty is that these things are LOUD! I'd like to find out if there are any temperature monitors inside the thing, and if I can run the fans at a reduced speed, or remove some of the fans to make them reasonable in a home environment. They don't do a lot (as I just do some CPU-intensive stuff on them every once in a while, and very little disk-I/O).
Thus, I'd like to find a contact for simple (but technical) hardware questions like these on the Origin 200. If you guys could send me a friendly contact or two, I'd be very grateful.
(I'm also interested in making the thing dual-boot Irix & Linux, if the Linux port is close to operating... I've also got a pair of Indys that I'm planning on sacrificing to the Linux gods...)
Thanks in advance--
--marco
Nick--
First of all, thanks for responding!
Do you know any way to make the Origin 200 operate more quietly? I'm a hardware geek, so I know that there are cooling issues and air-flow issues, but the darned thing is so loud that I can't just keep it running all the time. If I keep it on, it's distracting, even when I put it in another room with the door closed. (My hearing is pretty sensitive...)
It's in an air-conditioned house, and I don't mind putting in some temperature sensors to shut it off when it gets too warm inside... I'd hate to go to the trouble of creating a noise-muffling cabinet if there's some known way of making the beast a bit quieter. (Since I don't beat the disk drives up, they shouldn't generate much heat. I wouldn't mind pulling out all the drives but one, if that would help...)
Since I have a couple of 'em (as well as another couple of loud rack-mount boxes), I've even considered building a custom cabinet with a single large-capacity fan in it to draw air through all four boxes, and mount a dozen LM34-based temperature sensors at strategic points in the boxes to shut 'em all down if it gets too warm in the cabinet...
--marco
Quoted 38 lines · [email protected] wrote:
They are running at reduced speed unless the temp is over ~90. I can answer most common questions about them.
NickQuoted 32 lines · Marco C. Mason
Hello, OSS @ SGI gang--
I need a little help, please! As a result of a company closing, I've received a pair of SGI Origin 200 servers. Unfortunately, since the support contract on them has expired, I can't seem to use any of the support services at www.sgi.com.
I'm just a home experimenter who wants to run the things 'til they die. I'm very pleased with the performance, software, etc., and I'm very familiar with them (as I worked on them 8 hrs / day for a year and a half until the office closed).
The only difficulty is that these things are LOUD! I'd like to find out if there are any temperature monitors inside the thing, and if I can run the fans at a reduced speed, or remove some of the fans to make them reasonable in a home environment. They don't do a lot (as I just do some CPU-intensive stuff on them every once in a while, and very little disk-I/O).
Thus, I'd like to find a contact for simple (but technical) hardware questions like these on the Origin 200. If you guys could send me a friendly contact or two, I'd be very grateful.
(I'm also interested in making the thing dual-boot Irix & Linux, if the Linux port is close to operating... I've also got a pair of Indys that I'm planning on sacrificing to the Linux gods...)
Thanks in advance--
--marco
Ralf--
Thanks for your reply!
--marco
Quoted 29 lines · Ralf Baechle
Quoted 6 lines · Marco C. Mason
The only difficulty is that these things are LOUD! I'd like to find out if there are any temperature monitors inside the thing, and if I can run the fans at a reduced speed, or remove some of the fans to make them reasonable in a home environment. They don't do a lot (as I just do some CPU-intensive stuff on them every once in a while, and very little disk-I/O).
Via the system controller you can set the fan speed. Only the fan speeds n like normal and h like high are supported. If the machine feels like it is hot or one of the fans has failed it'll automatically switch the fan speed to h. If more than one fan fails it'll power off ...
Quoted 3 lines
Thus, I'd like to find a contact for simple (but technical) hardware questions like these on the Origin 200. If you guys could send me a friendly contact or two, I'd be very grateful.
Well, try this list.
Quoted 3 lines
(I'm also interested in making the thing dual-boot Irix & Linux, if the Linux port is close to operating... I've also got a pair of Indys that I'm planning on sacrificing to the Linux gods...)
The Indy port is in reasonable shape; the O200 port has decayed a bit over the past months but as far as time permits I'm working on getting it to run again.
Ralf
Quoted 10 lines · Marco C. Mason
Nick--
First of all, thanks for responding!
Do you know any way to make the Origin 200 operate more quietly? I'm a hardware geek, so I know that there are cooling issues and air-flow issues, but the darned thing is so loud that I can't just keep it running all the time. If I keep it on, it's distracting, even when I put it in another room with the door closed. (My hearing is pretty sensitive...)
This thread is off-topic for the devfs list. Please keep this on the linux-mips list.
Regards, Richard.... Permanent: [email protected] Current: [email protected]