Execute Reset via CheckStop approach
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 4 lines · In message <[email protected]> you wrote:
But this is not enough. It looks like the CHSTP bit in the DER (Debug Enable Regsiter) is set preventing the
HRESET_Nsequence from the CPU. This DER is not a normal special register. Do you have an example how I can clear it?
The DER should be set by your formware. Fix this!
And the DER _is_ a normal special register (# 149).
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] ...when fits of creativity run strong, more than one programmer or writer has been known to abandon the desktop for the more spacious
floor. - Fred Brooks, Jr.
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi Wolfgang,
Quoted 2 lines
The DER should be set by your formware. Fix this!
I cleared CFG_DER in ppcboot to clear the CHSTP bit. After that I needed to map in the br0 range and to make the asm's volatile and set the input/output parameters of the asm to get the HRESET_N pulse. So this is the version which works (on a MPC823e) in the context of the Linux kernel:
/* Get base address mapped by BR0/OR0 and map it in */
val = ((immap_t *)IMAP_ADDR)->im_memctl.memc_br0 & 0xFFFF8000;
val = (int) ioremap( retval, 0x4000 );
cli();
/* Enable CheckStop Reset */
((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr |= 0x00000080;
/* Invalidate BR0 mapping */
((immap_t *)IMAP_ADDR)->im_memctl.memc_br0 &= ~0x1;
/* Clear ME in MSR and cause CheckStop */
__asm__ volatile("mfmsr %0" : "=r" (msr) );
msr &= ~0x1000;
__asm__ volatile("mtmsr %0": : "r" (msr) );
val = * (unsigned char *) val;
printk("Restart failed\n");
while(1)
;Cheers,
Bart
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi,
Quoted 3 lines · in message <[email protected]> you wrote:
I cleared
CFG_DERin ppcboot to clear the CHSTP bit. After that I needed to map in the br0 range and to make the asm's volatile and set the input/output
Why do you think you have to do this? This is _NOT_ necessary.
Quoted 6 lines
parameters of the asm to get the
HRESET_Npulse. So this is the version which works (on a MPC823e) in the context of the Linux kernel:/* Get base address mapped by BR0/OR0 and map it in */ val = ((immap_t *)IMAP_ADDR)->im_memctl.memc_br0 & 0xFFFF8000; val = (int) ioremap( retval, 0x4000 );
This code is wrong. You clobber the value of "val" here.
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-4596-87 Fax: (+49)-8142-4596-88 Email: [email protected] Defaults are wonderful, just like fire.
- Larry Wall in <[email protected]>
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/