Skip to contentSkip to conversation

2.4.20pre5 atyfb patch for ATI Rage Mobility P/M AGP

PATCH Andreas Steinmetz 1 participant 1 message Sep 5, 2002 Framebuffer layer

lore
Share & tools
lore
#0 lore raw

The attached patch enables the usage of the ATI framebuffer for the ATI Rage Mobility of my Gateway Solo 9300 Laptop. I did send this patch to Geert Uytterhoeven in September 2001 but he doesn't seem interested. There are, however, more people for which the standard atyfb doesn't work (garbled display). These reports can be easily found using search engines. I do hope that this patch enables atyfb for them. It doesn't matter if this patch is never accepted, it was already ignored for a year by the maintainer and in a few years the problematic laptops will be dead anyway...

System info regarding ATI:

lspci output:

01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64)

System boot info:

atyfb: using auxiliary register aperture
atyfb: 3D RAGE Mobility (PCI) [0x4c4d rev 0x64] 8M SGRAM, 29.498928 MHz XTAL, 23 5 MHz PLL, 63 Mhz MCLK
Console: switching to colour frame buffer device 128x48
fb0: ATY Mach64 frame buffer device on PCI

Signature · 2 lines
Andreas Steinmetz
D.O.M. Datenverarbeitung GmbH
drivers/video/aty/atyfb_base.c +5 -2
diff -rNu linux/drivers/video/aty/atyfb_base.c linux-custom/drivers/video/aty/atyfb_base.c
@@ -359,7 +359,7 @@
     { 0x4c50, 0x4c50, 0x00, 0x00, m64n_ltp_p,   230, 100, M64F_GT | M64F_INTEGRATED | M64F_RESET_3D | M64F_GTB_DSP },
 
     /* 3D RAGE Mobility */
-    { 0x4c4d, 0x4c4d, 0x00, 0x00, m64n_mob_p,   230,  50, M64F_GT | M64F_INTEGRATED | M64F_RESET_3D | M64F_GTB_DSP | M64F_MOBIL_BUS },
+    { 0x4c4d, 0x4c4d, 0x00, 0x00, m64n_mob_p,   235,  63, M64F_GT | M64F_INTEGRATED | M64F_RESET_3D | M64F_GTB_DSP | M64F_MOBIL_BUS | M64F_XL_DLL },
     { 0x4c4e, 0x4c4e, 0x00, 0x00, m64n_mob_a,   230,  50, M64F_GT | M64F_INTEGRATED | M64F_RESET_3D | M64F_GTB_DSP | M64F_MOBIL_BUS },
 #endif /* CONFIG_FB_ATY_CT */
 };
@@ -754,7 +754,10 @@
     aty_set_crtc(info, &par->crtc);
     aty_st_8(CLOCK_CNTL + info->clk_wr_offset, 0, info);
 					/* better call aty_StrobeClock ?? */
-    aty_st_8(CLOCK_CNTL + info->clk_wr_offset, CLOCK_STROBE, info);
+    if (M64_HAS(MOBIL_BUS)&&M64_HAS(XL_DLL))
+	aty_st_8(CLOCK_CNTL + info->clk_wr_offset, CLOCK_STROBE|CLOCK_SEL|CLOCK_DIV, info);
+    else
+	aty_st_8(CLOCK_CNTL + info->clk_wr_offset, CLOCK_STROBE, info);
 
     info->dac_ops->set_dac(info, &par->pll, par->crtc.bpp, accelmode);
     info->pll_ops->set_pll(info, &par->pll);
drivers/video/aty/mach64_ct.c +9 -2
diff -rNu linux/drivers/video/aty/mach64_ct.c linux-custom/drivers/video/aty/mach64_ct.c
@@ -204,6 +204,11 @@
 	    break;
     }
 
+    if (M64_HAS(MOBIL_BUS)&&M64_HAS(XL_DLL)) {
+	pll->pll_ext_cntl |= 0xc8;
+	pll->mclk_fb_div -= 1;
+    }
+
     pll->pll_vclk_cntl = 0x03;	/* VCLK = PLL_VCLK/VCLKx_POST */
     pll->vclk_post_div = vpostdiv;
 }
@@ -250,8 +255,10 @@
 	else
 	    aty_st_pll(DLL_CNTL, 0xa0, info);
 	aty_st_pll(VFC_CNTL, 0x1b, info);
-	aty_st_le32(DSP_CONFIG, pll->ct.dsp_config, info);
-	aty_st_le32(DSP_ON_OFF, pll->ct.dsp_on_off, info);
+	if (!(M64_HAS(MOBIL_BUS)&&M64_HAS(XL_DLL))) {
+	    aty_st_le32(DSP_CONFIG, pll->ct.dsp_config, info);
+	    aty_st_le32(DSP_ON_OFF, pll->ct.dsp_on_off, info);
+	}
     }
 }