A500 hang up 2.4.19-pa18 (lot of) details

parisc-linux Thibaut VARENE 2 participants 2 messages Sep 17, 2002

Share & tools

Thibaut VARENE

author

2002-09-17 17:19 UTC #0 lore raw

This a forward to the p-l.o m-l about hang-up with 2.4.19-pa18 kernel, that occurs when playing around with setiathome. See the transcript for details.

info taken from System.map:

mkhppa3:~# ./a.out 000000001015c620
0x1015c620 kmem_cache_free+a8
mkhppa3:~# ./a.out 000000001015bfb0
0x1015bfb0 free_block+48

BTW, you'll notice that the second CPU timed-out, instead of dumping when the first one died...

HTH

Quoted 703 lines · Thibaut VARENE

I was able to reproduce the same hang, with a little variant:
the first time i hanged the box, i launched both seti one after the other (i.e., "cd seti1; ./setiathome &" and then "cd ../seti2; ./setiathome &") and the box crashed when firing the second one.
Here i started one. then did some small commands like "ls", "top" and so, and then started the second one. It didn't crash. I did a top, ls, ps -ef, no pb. Then i decided to stop both setis (killall setiathome), and start one again. It crahsed.
See the following session transcript:
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 0.97 root@c3k Tue Nov 27 14:51:48 MST 2001
Information: Boot device can't seek past 2Gb (ignore next error).byteio_read: seekread() returned -1 expected 2048
Partition Start(MB) End(MB) Id Type
1               1      15   f0 Palo
2              16     503   82 swap
3             504    2887   83 ext2
PALO(F0) partition contains:
    0/vmlinux64 3990942 bytes @ 0x44000
Information: No console specified on kernel command line. This is normal. PALO will choose the console currently used by firmware (serial). Command line for kernel: 'root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102' Selected kernel: /boot/vmlinux from partition 3
ELF64 executable
Entry 00100000 first 00100000 n 4
Segment 0 load 00100000 size 2448040 mediaptr 0x1000
Segment 1 load 00356000 size 1043344 mediaptr 0x257000 Segment 2 load 00458000 size 431368 mediaptr 0x356000
Segment 3 load 004c4000 size 49152 mediaptr 0x3c0000 Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.4.19-pa18 (root@mkhppa3) (gcc version 3.0) #1 SMP Sun Sep 15 18:21:12 CEST 2002 FP[0] enabled: Rev 1 Model 16
The 64-bit Kernel has started...
Determining PDC firmware type: 64 bit PAT.
model 00005d50 00000491 00000000 00000001 5cbb53d8 100000f0 00000008 000000b2 000000b2 vers 00000301
CPUID vers 18 rev 11 (0x0000024b)
capabilities 0x1
model 9000/800/A500-5X
Total Memory: 1024 Mb
pagetable_init
On node 0 totalpages: 262144
zone(0): 262144 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102
Calibrating delay loop... 1097.72 BogoMIPS
Memory: 1019664k available
Dentry cache hash table entries: 131072 (order: 9, 2097152 bytes)
Inode cache hash table entries: 65536 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 16384 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 65536 (order: 7, 524288 bytes)
Page-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Searching for devices...
Found devices:
1. Crescendo 550 (0) at 0xfffffffffffa0000 [160], versions 0x5d5, 0x0, 0x4
2. Crescendo 550 (0) at 0xfffffffffffa2000 [162], versions 0x5d5, 0x0, 0x4
3. Astro BC Runway Port (12) at 0xfffffffffed00000 [0], versions 0x582, 0x0, 0xb
4. Elroy PCI Bridge (13) at 0xfffffffffed30000 [0/0], versions 0x782, 0x0, 0xa
5. Elroy PCI Bridge (13) at 0xfffffffffed34000 [0/2], versions 0x782, 0x0, 0xa
6. Elroy PCI Bridge (13) at 0xfffffffffed38000 [0/4], versions 0x782, 0x0, 0xa
7. Elroy PCI Bridge (13) at 0xfffffffffed3c000 [0/6], versions 0x782, 0x0, 0xa
8. Memory (1) at 0xfffffffffed08000 [8], versions 0x9b, 0x0, 0x9
CPU(s): 2 x PA8600 (PCX-W+) at 550.000000 MHz
SBA found Astro 2.1 at 0xfffffffffed00000
lba version TR4.0 (0x5) found at 0xfffffffffed30000
lba range[2] : ignoring GMMIO (0xfffffff804000000)
lba version TR4.0 (0x5) found at 0xfffffffffed34000
lba range[2] : ignoring GMMIO (0xfffffff904000000)
lba version TR4.0 (0x5) found at 0xfffffffffed38000
lba range[2] : ignoring GMMIO (0xfffffffa04000000)
lba version TR4.0 (0x5) found at 0xfffffffffed3c000
lba range[2] : ignoring GMMIO (0xfffffffb04000000)
POSIX conformance testing by UNIFIX
FP[1] enabled: Rev 1 Model 16
SMP: Total 2 of 2 processors activated (2195.46 BogoMIPS noticed).
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Soft power switch support not available.
Performance monitoring counters enabled for Crescendo 550
Starting kswapd
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 [email protected]).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (103c,1048,103c,1049)
and the manufacturer and name of serial board or modem board
to [email protected].
ttyS00 at iomem 0xfffffffff8000000 (irq = 132) is a 16550A
ttyS01 at iomem 0xfffffffff8000008 (irq = 132) is a 16550A
ttyS02 at iomem 0xfffffffff8000010 (irq = 132) is a 16550A
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (103c,1048,103c,104a)
and the manufacturer and name of serial board or modem board
to [email protected].
ttyS03 at iomem 0xfffffffff8006000 (irq = 133) is a 16550A
ttyS04 at iomem 0xfffffffff8006008 (irq = 133) is a 16550A
Generic RTC Driver v1.02 05/27/1999 Sam Creasey ([email protected])
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Linux Tulip driver version 0.9.15-pre11 (May 11, 2002)
tulip0: no phy info, aborting mtable build
tulip0: MII transceiver #1 config 1000 status 782d advertising 0061.
eth0: Digital DS21143 Tulip rev 65 at 0xfffffffff8007000, 00:30:6E:0C:8A:8F, IRQ 128. SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 2, function 0
sym53c8xx: 53c875 detected
sym53c8xx: at PCI bus 0, device 2, function 1
sym53c8xx: 53c875 detected
sym53c8xx: at PCI bus 0, device 1, function 0
sym53c8xx: setting PCI_COMMAND_INVALIDATE (fix-up)
sym53c8xx: 53c896 detected
sym53c8xx: at PCI bus 0, device 1, function 1
sym53c8xx: setting PCI_COMMAND_INVALIDATE (fix-up)
sym53c8xx: 53c896 detected
sym53c875-0: rev 0x14 on pci bus 0 device 2 function 0 irq 130
sym53c875-0: ID 7, Fast-10, Parity Checking
sym53c875-1: rev 0x14 on pci bus 0 device 2 function 1 irq 131
sym53c875-1: ID 7, Fast-20, Parity Checking
sym53c896-2: rev 0x7 on pci bus 0 device 1 function 0 irq 129
sym53c896-2: ID 7, Fast-20, Parity Checking
sym53c896-2: handling phase mismatch from SCRIPTS.
sym53c896-3: rev 0x7 on pci bus 0 device 1 function 1 irq 130
sym53c896-3: ID 7, Fast-20, Parity Checking
sym53c896-3: handling phase mismatch from SCRIPTS.
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
scsi2 : sym53c8xx-1.7.3c-20010512
scsi3 : sym53c8xx-1.7.3c-20010512
Vendor: SEAGATE Model: ST39103LC Rev: HP02
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi1, channel 0, id 15, lun 0
sym53c875-1-<15,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset 15)
SCSI device sda: 17783112 512-byte hdwr sectors (9105 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 48Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 421k freed
INIT: version 2.84 booting
Activating swap.
Adding Swap: 499704k swap-space (priority -1)
Checking root file system...
fsck 1.27 (8-Mar-2002)
/dev/sda3: clean, 57492/305216 files, 321970/610304 blocks
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,3), internal journal
System time was Mon Sep 16 10:11:13 UTC 2002.
Setting the System Clock using the Hardware Clock as reference...
System Clock set. System local time is now Mon Sep 16 10:10:05 UTC 2002.
Calculating module dependencies... depmod: Can't open /lib/modules/2.4.19-pa18/modules.dep for writing done.
Loading modules:
modprobe: Can't open dependencies file /lib/modules/2.4.19-pa18/modules.dep (No such file or directory) Checking all file systems...
fsck 1.27 (8-Mar-2002)
/dev/sda5: clean, 104123/366528 files, 553485/732412 blocks
/dev/sda6 has been mounted 35 times without being checked, check forced.
/dev/sda6: 132287/376096 files (6.2% non-contiguous), 695541/751356 blocks
Setting kernel variables.
Mounting local filesystems...
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/dev/sda5 on /home type ext3 (rw)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/dev/sda6 on /work type ext3 (rw)
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces: done.
Starting portmap daemon: portmap.
Loading the saved-state of the serial devices...
Cannot set serial info: Device or resource busy
/dev/ttyS0 at 0x0000 (irq = 132) is a 16550A
/dev/ttyS1 at 0x0500 (irq = 133) is a 16550A
/dev/ttyS2 at 0x0000 (irq = 132) is a 16550A
/dev/ttyS3 at 0x0000 (irq = 133) is a 16550A
Setting the System Clock using the Hardware Clock as reference... System Clock set. Local time: Mon Sep 16 12:11:23 CEST 2002
Cleaning: /tmp /var/lock /var/run.
eth0: Setting half-duplex based on MII#1 link partner capability of 0021. Initializing random number generator... done.
Recovering nvi editor sessions... done.
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting NFS common utilities: statd.
Starting internet superserver: inetd.
Starting OpenBSD Secure Shell server: sshd.
Starting NTP server: ntpd.
Starting NFS servers: nfsd mountd.
Starting periodic command scheduler: cron.
Debian GNU/Linux testing/unstable mkhppa3 ttyS0
mkhppa3 login: varenet
Password:
Last login: Mon Sep 16 12:02:45 2002 from grobluk.esiee.fr on pts/0
Linux mkhppa3 2.4.19-pa18 #1 SMP Sun Sep 15 18:21:12 CEST 2002 parisc64 unknown unknown GNU/Linux
Most of the programs included with the Debian GNU/Linux system are freely redistributable; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law.
[varenet@mkhppa3 ~]$ cd seti
seti1
seti2
setiathome-3.03.hppa-parisc-palinux.tar [varenet@mkhppa3 ~]$ cd seti1/
[varenet@mkhppa3 ~/seti1]$ ./setiathome &
[1] 185
[varenet@mkhppa3 ~/seti1]$ >>DEBUG : Use LOCKFSETI@home client.
Platform: hppa-parisc-palinux
Version: 3.03
SETI@home is sponsored by individual donors around the world. If you'd like to contribute to the project,
please visit the SETI@home web site at
http://setiathome.ssl.berkeley.edu.
The project is also sponsored by the Planetary Society, the University of California, Sun Microsystems, Paramount Pictures, Fujifilm Computer Products, Informix, Engineering Design Team Inc, The Santa Cruz Operation (SCO), Intel, Quantum Corporation, and the SETI Institute.
SETI@home was developed by David Gedye (Founder),
David Anderson (Director), Dan Werthimer (Chief Scientist), Leonard Chung, Hiram Clawson, Jeff Cobb, Charles Congdon, Charlie Fenton, Kyle Granger, Eric Heien, Mike Hill, Michael Kang, Eric Korpela, Matt Lebofsky, Peter Leiser, Brad Silen, Woody Sullivan, and Adam Wight.
Scanning data file
Data Info:
Sky coordinates:  1.605 R.A.,  8.090 Dec
Recorded on:  2452319.35352 (Wed Feb 13 20:29:04 2002)
Source: Arecibo Radio Observatory
Base Frequency: 1.421201172 GHz
Found data file: yes. Found result header file: yes.
Scanning result header file.
Beginning analysis...
(This is the last message displayed while the client works. To see progress messages between now and completion of processing, operate the client with the -verbose option. You can also see the progress of the client by looking at
12:11:58 up 3 min, 1 user, load average: 0.74, 0.48, 0.19
23 processes: 21 sleeping, 2 running, 0 zombie, 0 stopped
CPU states:   0.1% user,   0.9% system,  48.1% nice,  50.9% idle
Mem:   1020088K total,   101308K used,   918780K free,     1468K buffers
Swap:   499704K total,        0K used,   499704K free,     9792K cached
  PID USER     PRI  NI  SIZE  RSS SHARE STAT %CPU %MEM   TIME COMMAND
  185 varenet   18   1 13772  13M   376 R N  97.4  1.3   0:11 setiathome
  187 varenet   12   0  1128 1132   912 R     0.7  0.1   0:00 top
    1 root       9   0   612  616   520 S     0.0  0.0   0:07 init
    2 root       9   0     0    0     0 SW    0.0  0.0   0:00 keventd
    3 root      19  19     0    0     0 SWN   0.0  0.0   0:00 
ksoftirqd_CPU0
    4 root      18  19     0    0     0 SWN   0.0  0.0   0:00 
ksoftirqd_CPU1
    5 root       9   0     0    0     0 SW    0.0  0.0   0:00 kswapd
    6 root       9   0     0    0     0 SW    0.0  0.0   0:00 bdflush
    7 root       9   0     0    0     0 SW    0.0  0.0   0:02 kupdated
    8 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   66 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   67 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   90 daemon     9   0   564  564   452 S     0.0  0.0   0:00 portmap
  146 root       9   0  1004 1004   840 S     0.0  0.0   0:00 syslogd
  149 root       9   0  1424 1424   508 S     0.0  0.1   0:00 klogd
  153 root       9   0   840  840   712 S     0.0  0.0   0:00 rpc.statd
[varenet@mkhppa3 ~]$ cd seti2/
[varenet@mkhppa3 ~/seti2]$ ./setiathome &
[2] 188
[varenet@mkhppa3 ~/seti2]$ >>DEBUG : Use LOCKFSETI@home client.
Platform: hppa-parisc-palinux
Version: 3.03
SETI@home is sponsored by individual donors around the world. If you'd like to contribute to the project,
please visit the SETI@home web site at
http://setiathome.ssl.berkeley.edu.
The project is also sponsored by the Planetary Society, the University of California, Sun Microsystems, Paramount Pictures, Fujifilm Computer Products, Informix, Engineering Design Team Inc, The Santa Cruz Operation (SCO), Intel, Quantum Corporation, and the SETI Institute.
SETI@home was developed by David Gedye (Founder),
David Anderson (Director), Dan Werthimer (Chief Scientist), Leonard Chung, Hiram Clawson, Jeff Cobb, Charles Congdon, Charlie Fenton, Kyle Granger, Eric Heien, Mike Hill, Michael Kang, Eric Korpela, Matt Lebofsky, Peter Leiser, Brad Silen, Woody Sullivan, and Adam Wight.
Scanning data file
Data Info:
Sky coordinates:  4.859 R.A., 18.010 Dec
Recorded on:  2452425.22882 (Thu May 30 17:29:29 2002)
Source: Arecibo Radio Observatory
Base Frequency: 1.420849609 GHz
Found data file: yes. Found result header file: yes.
Scanning result header file.
 12:12:37 up 4 min,  1 user,  load average: 1.20, 0.63, 0.25
24 processes: 21 sleeping, 3 running, 0 zombie, 0 stopped
CPU states:   0.1% user,   1.1% system,  98.8% nice,   0.0% idle
Mem:   1020088K total,   117088K used,   903000K free,     1548K buffers
Swap:   499704K total,        0K used,   499704K free,    10784K cached
  PID USER     PRI  NI  SIZE  RSS SHARE STAT %CPU %MEM   TIME COMMAND
  185 varenet   15   1 14984  14M   376 R N  99.8  1.4   0:49 setiathome
  188 varenet   16   1 13772  13M   376 R N  99.6  1.3   0:24 setiathome
  190 varenet   11   0  1128 1132   912 R     0.7  0.1   0:00 top
    1 root       9   0   612  616   520 S     0.0  0.0   0:07 init
    2 root       9   0     0    0     0 SW    0.0  0.0   0:00 keventd
    3 root      19  19     0    0     0 SWN   0.0  0.0   0:00 
ksoftirqd_CPU0
    4 root      18  19     0    0     0 SWN   0.0  0.0   0:00 
ksoftirqd_CPU1
    5 root       9   0     0    0     0 SW    0.0  0.0   0:00 kswapd
    6 root       9   0     0    0     0 SW    0.0  0.0   0:00 bdflush
    7 root       9   0     0    0     0 SW    0.0  0.0   0:02 kupdated
    8 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   66 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   67 root       9   0     0    0     0 SW    0.0  0.0   0:00 kjournald
   90 daemon     9   0   564  564   452 S     0.0  0.0   0:00 portmap
  146 root       9   0  1004 1004   840 S     0.0  0.0   0:00 syslogd
  149 root       9   0  1424 1424   508 S     0.0  0.1   0:00 klogd
q[varenet@mkhppa3 ~/seti2]$ killall setiathome
[varenet@mkhppa3 ~/seti2]$ cat /proc/version
Linux version 2.4.19-pa18 (root@mkhppa3) (gcc version 3.0) #1 SMP Sun Sep 15 18:21:12 CEST 2002
[1]- Terminated ./setiathome (wd: ~/seti1)
(wd now: ~/seti2)
[2]+ Terminated ./setiathome
[varenet@mkhppa3 ~/seti2]$ crontab -l
@hourly cd /home/varenet/seti1; ./setiathome -nice 20 -proxy
cache:3128 &
#@reboot cd /home/varenet/dnetc; ./dnetc
@hourly cd /home/varenet/seti2; ./setiathome -nice 20 -proxy
cache:3128 &
[varenet@mkhppa3 ~/seti2]$ cd /home/varenet/seti1; ./setiathome -nice 20
-proxy cache:3128 &
WARNING! Stack pointer and cr30 do not correspond!
Dumping virtual address stack instead
Dumping Stack from 0x000000005f5a0000 to 0x000000005f5a4dc0:
And nothing more.
after a toc, here was the content of SER PIM output:
(I dumped everything, not sure of what may be useful or not ;)
Main Menu: Enter command or menu > ser pim
PROCESSOR PIM INFORMATION
----------------- Processor 0 HPMC Information - PDC Version: 40.50 ------
Timestamp = Tue Oct 23 19:05:06 GMT 2001 (20:01:10:23:19:05:06)
HPMC Chassis Codes
       Chassis Code        Extension
       ------------        ---------
       0x0000082000ff6242  0x0000000000000000
       0x1800082011006322  0xcb81800000000000
       0x0000087000ff6292  0x0000000000000000
       0x6000082070006062  0x0000000000100010
       0x7000082070006082  0x0000000000b92400
       0x7000082379006133  0xc1bff0fffed08040
       0x0000080080006310  0x0000000000000001
       0x000008008000631f  0x0000000000000000
General Registers 0 - 31
00-03  0000000000000000  00000000103f9bb0  0000000010100bac 00000000103f6bb0
04-07  000000000003d5ea  000000000038a000  00000000000000f0 0000000000000000
08-11  0000000000000000  0000000000000001  000000000804000e 000000001040888c
12-15  00000000000000f2  00000000000000fa  00000000000000f0 00000000000000ff
16-19  00000000f00003dc  00000000f000028c  00000000f0002aa4 00000000104a8000
20-23  0000000000000000  0000000000000000  0000000000000001 000000004fa5c824
24-27  000000000800000f  0000000000000032  0000000000000019 00000000103f6bb0
28-31  0000000000000000  00000000104a8b70  00000000104a8b00 00000000104043b0
Control Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000000000000  0000000000000000  0000000000000000 0000000000000000
08-11  0000000000000072  0000000000000000  00000000000000c0 000000000000003f
12-15  0000000000000000  0000000000000000  0000000000104000 ffffffffffffffff
16-19  0000000f96e6aa48  0000000000000000  0000000010100b88 0000000003c008b3
20-23  0000000000000000  0000000000000000  000000000804000f 0000000000000000
24-27  0000000000389000  000000003f158000  ffffffffffff7f10 ffffffffffff7fff
28-31  ffffffffffffffff  ffffffffffffffff  00000000104a8000 00000000104b0000
Space Registers 0 - 7
00-03  00001c80          00000000          00000000          00001c80
04-07  00000000          00000000          00000000          00000000
IIA Space (back entry)       = 0x0000000000000000
IIA Offset (back entry)      = 0x0000000010100b8c
Check Type                   = 0x20000000
CPU State                    = 0x9e000004
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x0030000d
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0xfffffffffffa0000
System Requestor Address     = 0xfffffffffffa0000
Floating Point Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000010388100  0000000100000001  0000000012a20000 0000000000000000
08-11  0000000000000802  000000004fa78000  00000000103f6bb0 000000004fa6fec0
12-15  0000000000000000  0000000010388100  000000001018197c 00000000103fcbb0
16-19  0000000010388100  0000000000000002  0000000000000002 000000001032d2d4
20-23  0000000000000001  0000000010388a80  0000000000000000 00000000000000c0
24-27  0000000a10332690  00000000104fce18  000000000800000f 00000000103d2af0
28-31  00000000103d2b20  0000000000000001  0000000010162de0 0000000000000002
Check Summary                = 0xcb81800000000000
Available Memory             = 0x0000000040000000
CPU Diagnose Register 2      = 0x0301000000802004
CPU Status Register 0        = 0x3440c20000000000
CPU Status Register 1        = 0x8000000000000000
SADD LOG                     = 0x4820000000000000
Read Short LOG               = 0xc1bff0fffed22310
----------------- Processor 0 LPMC Information ------------------
Check Type                   = 0x00000000
IC Parity Info               = 0x00000000
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x00000000
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0x0000000000000000
System Requestor Address     = 0x0000000000000000
----------------- Processor 0 TOC Information -------------------
General Registers 0 - 31
00-03  0000000000000000  000000001037fa30  000000001010cca0 0000000010443f10
04-07  000000004f5a5480  000000000000000f  000000001032adfc 000000005f5a0018
08-11  000000001051f190  000000001051f1a0  000000000000002e 0000000000000001
12-15  0000000000000003  000000000000002f  0000000000000000 0000000000000002
16-19  000000004f5a5480  00000000000ad800  000000000009e800 0000000000000000
20-23  000000001037fa30  0000000000000000  000000001038f690 000000005f5a0018
24-27  000000000000000f  000000004f5a5480  000000001032adfc 0000000010443f10
28-31  0000000000000040  000000004f5a5930  000000004f5a59c0 ffffffffffffffff
Control Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000000000000  0000000000000000  0000000000000000 0000000000000000
08-11  000000000000015a  0000000000000000  00000000000000c0 000000000000003e
12-15  0000000000000000  0000000000000000  0000000000107000 0000000000000000
16-19  00000059f094e5b5  0000000000000000  000000001010c990 0000000086603fed
20-23  0000000000240000  00000000dff7fa30  000000000804000e a000000000000000
24-27  00000000003d2000  000000003d24b000  ffffffffffff7f00 ffffffffffffffff
28-31  ffffffffffff7fff  ffffffffffffffff  000000004f5a4000 00000000104c8000
Space Registers 0 - 7
00-03  00005680          00005680          00000000          00005680
04-07  00000000          00000000          00000000          00000000
IIA Space (back entry)       = 0x0000000000000000
IIA Offset (back entry)      = 0x000000001010c994
CPU State                    = 0x9e000001
----------------- Processor 1 HPMC Information - PDC Version: 40.50 ------
Timestamp = Tue Oct 23 19:05:06 GMT 2001 (20:01:10:23:19:05:06)
HPMC Chassis Codes
       Chassis Code        Extension
       ------------        ---------
       0x0000082000ff6242  0x0000000000000000
       0x1800082011016312  0xcb81000000000000
General Registers 0 - 31
00-03  0000000000000000  0000000010368068  000000001022f13c 000000004fb29240
04-07  fffffffff8006030  00000000103f6bb0  00000000103f6bb0 fffffffff8006000
08-11  000000004fb29000  fffffffff8006028  0000000000002000 fffffffff8006030
12-15  000000000000012c  000000004f0d0b08  0000000000018054 0000000000018414
16-19  0000000000000000  0000000000000001  0000000000026228 fffffffff8006000
20-23  0000000000000000  0000000000000000  0000000000000000 0000000000000000
24-27  0000000000000000  fffffffff8006060  fffffffff8006030 00000000103f6bb0
28-31  000000000000d6d8  000000004f0d10f0  000000004f0d1100 000000000000003f
Control Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000000000000  0000000000000000  0000000000000000 0000000000000000
08-11  000000000000007c  0000000000000000  00000000000000c0 0000000000000002
12-15  0000000000000000  0000000000000000  0000000000104000 ffffffffffffffff
16-19  0000000f96e6acc4  0000000000000000  0000000010270798 000000000f40019a
20-23  00000000ae27ffe0  c000000001806030  000000ff0804f40f 8000000000000000
24-27  0000000000389000  000000003f130000  ffffffffffffffff ffffffffffff7fff
28-31  ffffffffffffffff  ffffffffffffffff  000000004f0d0000 000000004fb78000
Space Registers 0 - 7
00-03  00001f00          00000000          00000000          00001f00
04-07  00000000          00000000          00000000          00000000
IIA Space (back entry)       = 0x0000000000000000
IIA Offset (back entry)      = 0x000000001027079c
Check Type                   = 0x20000000
CPU State                    = 0x9e000004
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x0030103b
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0x000000fff8006030
System Requestor Address     = 0xfffffffffffa2000
Floating Point Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000010388100  0000000100000001  0000000012a20000 0000000000000000
08-11  0000000000000802  000000004fa78000  00000000103f6bb0 000000004fa6fec0
12-15  0000000000000000  0000000010388100  000000001018197c 00000000103fcbb0
16-19  0000000010388100  0000000000000002  0000000000000002 000000001032d2d4
20-23  0000000000000001  0000000010388a80  0000000000000000 0000000000000000
24-27  0000000a10332690  00000000104fce18  000000000800000f 00000000103d2af0
28-31  00000000103d2b20  0000000000000001  0000000010162de0 0000000000000003
Check Summary                = 0xcb81000000000000
Available Memory             = 0x0000000040000000
CPU Diagnose Register 2      = 0x0301010000802004
CPU Status Register 0        = 0x2440c20000000000
CPU Status Register 1        = 0x8002000000000000
SADD LOG                     = 0x0c1912c0e840d002
Read Short LOG               = 0xc1af00fff8006030
----------------- Processor 1 LPMC Information ------------------
Check Type                   = 0x00000000
IC Parity Info               = 0x00000000
Cache Check                  = 0x00000000
TLB Check                    = 0x00000000
Bus Check                    = 0x00000000
Assists Check                = 0x00000000
Assist State                 = 0x00000000
Path Info                    = 0x00000000
System Responder Address     = 0x0000000000000000
System Requestor Address     = 0x0000000000000000
----------------- Processor 1 TOC Information -------------------
General Registers 0 - 31
00-03  0000000000000000  0000000010446f10  0000000010103714 0000000010443f10
04-07  00000000003d2000  fffffff0f040a000  0000000000000032 00000000000000f7
08-11  0000000000000000  fffffff0f0400000  000000000804000e 000000001045dbac
12-15  00000000000000f2  0000000000000001  00000000000000f0 00000000000000ff
16-19  000000f0f00000c4  fffffff0f040c000  0000000000000000 0000000011c50000
20-23  0000000000000000  0000000000000000  0000000000000001 000000001047f824
24-27  000000000800000f  0000000000000032  0000000000000019 0000000010443f10
28-31  0000000000000000  0000000011c50b30  0000000011c50ac0 0000000010450f10
Control Registers 0 - 31
00-03  0000000000000000  0000000000000000  0000000000000000 0000000000000000
04-07  0000000000000000  0000000000000000  0000000000000000 0000000000000000
08-11  0000000000000118  0000000000000000  00000000000000c0 000000000000003e
12-15  0000000000000000  0000000000000000  0000000000107000 ff80000000000000
16-19  0000005a0364ba5e  0000000000000000  00000000101036f0 0000000003c008b3
20-23  0000000000004480  0000000000000000  000000ff0806ff0f 0000000000000000
24-27  00000000003d2000  000000003daa2000  ffffffffffffffff ffffffffffffffff
28-31  ffffffffffffffff  ffffffffffffffff  0000000011c50000 ffffffffffffffff
Space Registers 0 - 7
00-03  00004480          00004480          00000000          00004600
04-07  00000000          00000000          00000000          00000000
IIA Space (back entry)       = 0x0000000000000000
IIA Offset (back entry)      = 0x00000000101036f4
CPU State                    = 0x9e000001
-------------- Memory Error Log Information --------------
Bus 0 Log Information
Timestamp = Tue Oct 23 19:05:06 GMT 2001 (20:01:10:23:19:05:06)
  OV  RQ  RS      ESTAT      A  C  D  corr  unc  fe  cw  pf
  --  --  --      -----      -  -  -  ----  ---  --  --  --
  X       X     ERR_ERROR       X            X
Bus Requestor Address      = 0xfffffffffffa0000
Bus Target Address         = 0x0000000000000000
Bus Responder Address      = 0xfffffffffed00000
Error Status Reg           = 0x0000000000100010
Runway Control Reg         = 0x0000021c00002818
Runway Address Reg         = 0xc1bff0fffed08040
Runway Data High Reg       = 0xf8018a1ff820ca01
Runway Data Low Reg        = 0xf8018a1ff820ca01
Memory Address Reg         = 0x000001ff3fffffff
Memory Address Corr Reg    = 0x000001ff3fffffff
Memory Syndrome Reg        = 0x0000000000000000
Memory Syndrome Corr Reg   = 0x0000000000000000
Address/Control Parity Error Registers
Address/Control Parity Error Bit (mem_addr_par_stat) Not Set
------------ I/O Module Error Log Information ------------
No I/O module errors logged
HTH,
Thibaut.
PS: when trying to boot after ser pim, the machine showed the following and hung again:
I dunno if that's normal ?
*****************************************
************* SYSTEM ALERT **************
SYSTEM NAME: a500
DATE: 09/16/2002 TIME: 10:23:28
ALERT LEVEL: 7 = reserved
REASON FOR ALERT
SOURCE: 0 = unknown, no source stated
SOURCE DETAIL: 0 = unknown, no source stated SOURCE ID: FF
PROBLEM DETAIL: 0 = no problem detail
LEDs:  RUN      ATTENTION     FAULT     REMOTE     POWER
       OFF      FLASH         ON        ON         ON
LED State: Boot Failed. Non-critical error detected. Check Chassis and Console Logs for error messages.
0x0000107000FF6292 00000000 00000000 - type 0 = Data Field Unused 0x5800187000FF6292 00006608 100A171C - type 11 = Timestamp 09/16/2002 10:23:28
A: ack read of this entry - X: Disable all future alert messages Anything else skip redisplay the log entry
->Choice:a
*****************************************
I had to issue a 'RS' to reboot the box.

Signature · 3 lines

Thibaut VARENE
PA/Linux ESIEE Team
http://pateam.esiee.fr/

Grant Grundler

2002-09-17 18:42 UTC #1 lore raw

Quoted 3 lines · Thibaut VARENE

This a forward to the p-l.o m-l about hang-up with 2.4.19-pa18 kernel, that occurs when playing around with setiathome. See the transcript for details.

I tried the same thing with setiathome on A500-4X (PA8500) and it seems to work fine.
Thibaut is using A500-5X (PA8600) - same cache sizes as PA8500. I was wondering if the is a problem with 4-way associative cache or just higher clock speeds exposing bugs.

grant