How to NOT redirect..
Hi, I'm using iptables for redirect requests to port 80 to port 3128 of Squid.
But I have a problem, because some of the squid users have trouble accessing certain services through the proxy, i want to this users bypass the proxy when they try to reach certain sites.
So How can i deny the redirect ?
I've excluded certain users for their source address... making the redirection to the remaining ip addresses.
But now i want to send all traffic to squid, all but certain destinations...
Is there a way to do that ?
I appreciate any help,
Thanks,
Karina
Quoted 9 lines · Karina Gómez Salgado
Hi, I'm using iptables for redirect requests to port 80 to port 3128 of Squid.
But I have a problem, because some of the squid users have trouble accessing certain services through the proxy, i want to this users bypass the proxy when they try to reach certain sites.
So How can i deny the redirect ?
Quoted 7 lines
I've excluded certain users for their source address... making the redirection to the remaining ip addresses.
But now i want to send all traffic to squid, all but certain destinations...
Is there a way to do that ?
Yes. Depending on how many destination address you do / don't want to
redirect, you could use any of the following three methods (there are almost certainly others as well):
1. Add a "-d a.b.c.d" to your DNAT rule so that only packets matching the
destination address get DNATted. You then need one of these rules for each
destination you want the DNAT to apply to.
2. Add a "-d ! a.b.c.d" if you want to stop a single destination from being
DNATted. You can only use one of these rules, otherwise two of them in
combination will have the same effect as not using "-d ! a.b.c.d" at all.
3. Use your existing DNAT rule in the PREROUTING nat chain, but insert some rules before it which match a destination address using "-d a.b.c.d" and use the target "-j ACCEPT" so that these packets bypass the DNAT rule.
Basically suggestion 1 allows you to apply DNAT to as many destination addresses as you like; suggestion 2 allows you to exclude one address or address range from being DNATted; and suggestion 3 allows you to exclude as many addresses or ranges as you want.
Somewhere in this you should be able to achieve your goal.
Antony.
Signature · 3 lines
Software development can be quick, high-quality, or low-cost. The customer gets to pick any two out of three.
Thank's a lot...
Now my problem is solved, and it was so easy!!
Regards,
Karina
Quoted 42 lines · Antony Stone
Quoted 9 lines · Karina Gómez Salgado
Hi, I'm using iptables for redirect requests to port 80 to port 3128 of Squid.
But I have a problem, because some of the squid users have trouble accessing certain services through the proxy, i want to this users bypass the proxy when they try to reach certain sites.
So How can i deny the redirect ?
Quoted 7 lines
I've excluded certain users for their source address... making the redirection to the remaining ip addresses.
But now i want to send all traffic to squid, all but certain destinations...
Is there a way to do that ?
Yes. Depending on how many destination address you do / don't want to
redirect, you could use any of the following three methods (there are almost certainly others as well):1. Add a "-d a.b.c.d" to your DNAT rule so that only packets matching the
destination address get DNATted. You then need one of these rules for each
destination you want the DNAT to apply to.2. Add a "-d ! a.b.c.d" if you want to stop a single destination from being
DNATted. You can only use one of these rules, otherwise two of them in
combination will have the same effect as not using "-d ! a.b.c.d" at all.3. Use your existing DNAT rule in the PREROUTING nat chain, but insert some rules before it which match a destination address using "-d a.b.c.d" and use the target "-j ACCEPT" so that these packets bypass the DNAT rule.
Basically suggestion 1 allows you to apply DNAT to as many destination addresses as you like; suggestion 2 allows you to exclude one address or address range from being DNATted; and suggestion 3 allows you to exclude as many addresses or ranges as you want.
Somewhere in this you should be able to achieve your goal.
Quoted 7 lines
Antony.
--
Software development can be quick, high-quality, or low-cost.
The customer gets to pick any two out of three.
--
LSCI Karina Gómez Salgado
mailto:[email protected]
Systems Administrator & Web Projects Manager
BTU Comunicación, S.A. de C.V.
Quoted 7 lines · Karina Gómez Salgado
Hi, I'm using iptables for redirect requests to port 80 to port 3128 of Squid.
But I have a problem, because some of the squid users have trouble accessing certain services through the proxy, i want to this users bypass the proxy when they try to reach certain sites.
I had a simillar problem where clients could access sites directly, but not when the transparent quid was setup. The problem was that the server had ECN enabled. Some brain-dead routers/firewalls filter out all packets with the ECN bit set. Disabling ECN on the firewall solved the problems. Try to look at the value of /proc/sys/net/ipv4/tcp_ecn. If the value is '1', then do an 'echo 0 > /proc/sys/net/ipv4/tcp_ecn' on the machine running the squid and see if the problem persists.
This might be an easier way to solve the problem rather than adding specific rules to let machines bypass the proxy.
Regards
Anders Fugmann
--
Author of FIAIF
FIAIF is an intelligent firewall
http://fiaif.fugmann.dhs.org