from intel onboard Lan and audo to install 2.4.50

DISCUSSION eric lin 1 participant 2 messages Dec 9, 2002 – Dec 11, 2002 1 message not in the archive

Share & tools

eric lin

author

2002-12-09 17:47 UTC #0 lore raw

Quoted 46 lines · Colin Watson

Quoted 11 lines · eric lin
the following dmesg seem to show it detect my ac97 is i810_audio but it said Primary codec not ready
please help on this
in 2.4.20 intel borad
/* eepro is also not work, both I all put in my /etc/modules */
sincere ERic
www.linuxspice.com
linux pc for sale
Quoted 15 lines
eepro_init_module: Probe is very dangerous in ISA boards!
eepro_init_module: Please add "autodetect=1" to force probe
CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Intel 810 + AC97 Audio, version 0.21, 23:23:34 Nov 30 2002
PCI: Found IRQ 3 for device 00:1f.5
PCI: Sharing IRQ 3 with 00:1f.3
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xe080 and 0xe400, IRQ 3
i810_audio: Audio Controller supports 6 channels.
i810_audio: Primary codec not ready.
As far as I can tell, this happens if the i810 doesn't have the ac97 codec. Assuming that it really is an i810 card [1], you might have better luck getting a response from the linux-kernel mailing list.
[1] You've explicitly put it in /etc/modules, so who knows! Note that I don't have to explicitly add i810_audio to /etc/modules or /etc/modutils/* for my laptop; instead the kernel works it out automatically.
Quoted 4 lines
eepro_init_module: Probe is very dangerous in ISA boards!
eepro_init_module: Please add "autodetect=1" to force probe

Quoted 6 lines

The eepro module needs at least an io argument to set the I/O base address(es), and possibly an irq argument too. You can use 'options' lines in /etc/modutils/* to set options that are always added when probing named modules; see the modules.conf(5) man page and remember to run update-modules after editing files in /etc/modutils.

my lspci -v result related to intel onboard LAN(assume is eepro)

Quoted 8 lines

02:08.0 Ethernet controller: Intel Corp.: Unknown device 1039 (rev 82)
Subsystem: Intel Corp.: Unknown device 3015
Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at feafe000 (32-bit, non-prefetchable) [size=4K] I/O ports at d880 [size=64]
Capabilities: <available only to root>

Quoted 4 lines

If it's a PCI card, you might want eepro100 instead?

I tried put a line in /etc/modutils/actions
insmod eepro autodetect=1 IO=d880 IRQ=11
reboot , still not work
(may be sytax is wrong, have any opinion? do see man page have its syntax on the option feature)

some say newest kernel 2.5.50 can solve all above hardware(intel board on board LAN and audio ) problem, so I download full tar.gz, choose what my hardware fit make install

error happen, I justify one of it, first one, in linux-2.4.50/include/asm-i386/io_apic.h containing sis_apic_bug not include its .h file

then re do make install
still error, this time I have no clue
-----------------------------------------------------
in.o sound/built-in.o arch/i386/pci/built-in.o net/built-in.o --end-group -o vmlinux drivers/built-in.o(.text+0x11f15): In function `kd_nosound':
: undefined reference to `input_event'
drivers/built-in.o(.text+0x11f31): In function `kd_nosound':
: undefined reference to `input_event'
drivers/built-in.o(.text+0x11fc8): In function `kd_mksound':
: undefined reference to `input_event'
drivers/built-in.o(.text+0x12baa): In function `kbd_bh':
: undefined reference to `input_event'
drivers/built-in.o(.text+0x12bb8): In function `kbd_bh':
: undefined reference to `input_event'
drivers/built-in.o(.text+0x12bc9): more undefined references to input_event' follow drivers/built-in.o(.text+0x13003): In function kbd_connect':
: undefined reference to input_open_device' drivers/built-in.o(.text+0x1301f): In function kbd_disconnect':
: undefined reference to input_close_device' drivers/built-in.o(.init.text+0xd71): In function kbd_init':
: undefined reference to `input_register_handler'
make: *** [vmlinux] Error 1
fsshl@www:~/linux-2.5.50$
------------------------------------------------------------

also I have difficult(unsuccess) patch 2.5.50
I did
gzip -cd patch-2.5.50-ac1.gz | patch -p0
in my home direction which I untar unzip linux-2.5.50.tar.gz it ask file to patch
I type patch-2.5.50-ac1.gz again, not right, so produc .orig and .rej files, please help on that

highly appreciate your help and your time
sincere Eric
www.linuxspice.com
linux pc for sale

A message that is not in the archive (sent off-list or not yet received): [email protected]

eric lin

author

2002-12-11 06:50 UTC #2 lore raw

Quoted 7 lines

Quoted 4 lines
some say newest kernel 2.5.50 can solve all above hardware(intel board on board LAN and audio ) problem, so I download full tar.gz, choose what my hardware fit make install
Use make-kpkg in the kernel-package package.

I did,
but it terminate with error

gcc -Wp,-MD,drivers/pci/.quirks.o.d -D__KERNEL__ -Iinclude -Wall
-Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common -fomit-frame-pointer -pipe -mpreferred-stack-boundary=2 -march=i686 -Iarch/i386/mach-generic -Iarch/i386/mach-defaults -nostdinc -iwithprefix include -DKBUILD_BASENAME=quirks -DKBUILD_MODNAME=quirks
-c -o drivers/pci/quirks.o drivers/pci/quirks.c
drivers/pci/quirks.c: In function `quirk_ioapic_rmw':
drivers/pci/quirks.c:354: `sis_apic_bug' undeclared (first use in this function) drivers/pci/quirks.c:354: (Each undeclared identifier is reported only once drivers/pci/quirks.c:354: for each function it appears in.) make[3]: *** [drivers/pci/quirks.o] Error 1
make[2]: *** [drivers/pci] Error 2
make[1]: *** [drivers] Error 2
make[1]: Leaving directory `/home/fsshl/linux-2.5.50'
make: *** [stamp-build] Error 2
www:/home/fsshl/linux-2.5.50#

if someone know it be modifed, please drop me a note where I can get the fixed source.
it's on 2.5.50.ac-1 patched 2.5.50 from kernel.org
hihgly apprecaite

Quoted 21 lines

Quoted 4 lines
error happen, I justify one of it, first one, in linux-2.4.50/include/asm-i386/io_apic.h containing sis_apic_bug not include its .h file
As Colin already said, if you can't handle this, you shouldn't be using 2.5 kernels. Some of them don't build, and many (most) have serious bugs that could cause data loss. If you want to go ahead with this, you'll have to get help from lkml, but be prepared to be thoroughly roasted.
Quoted 3 lines
also I have difficult(unsuccess) patch 2.5.50
I did
gzip -cd patch-2.5.50-ac1.gz | patch -p0
                                          ^
s/0/1/
-rob

Signature · 3 lines

Sincere Eric
www.linuxspice.com
linux pc for sale