Skip to contentSkip to conversation

Two questions on mtds on x86 platform

DISCUSSION Somashekara DM 3 participants 3 messages Feb 6, 2003 – Mar 14, 2007 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

Hi,

We want to mount jffs2 on two mtd partitions as a part of our project. Our platform is x86 - kernel version 2.4.13.

1. We are using mtdram ("Test driver using RAM") and blkmtd ("MTD emulation using block device")
to create two mtd's. Our aim is to mount jffs2 on two different
mtds.

Using mtdram and blkmtd at the same time is not successful.

we could mount first mtd device (which ever we loaded first)
successfully but failed to mount second mtd.
mount is giving error as "mount: fs type jffs2 not supported by
kernel".

Here are the steps we have followed.

Step1 :
mknod /dev/mtd0 c 90 0
mknod /dev/mtd2 c 90 2
and
mknod /dev/mtdblock0 b 31 0
mknod /dev/mtdblock2 b 31 2

Step2 :
load mtd driver for RAM and hard disk using 'mtdram' and 'blkmtd'
respectively.
insmod mtdram
insmod blkmtd device=/dev/hda7

Step3 :
write jffs2 image on theses device

Step4 :
mount jffs2 file system on these mtd's as follows

mount -t jffs2 /dev/mtdblock0 /mnt/jffs2drive0 //successfully
mounted
mount -t jffs2 /dev/mtdblock2 /mnt/jffs2drive2 //this mount fails
error - "mount: fs type jffs2 not supported by kernel"

What is going wrong here? Is it possible to use mtdram and blkmtd at the same time?
Can you give us the procedure for doing this?

2. Can we create multiple partitions on the 'mtdram'? Can you give us the procedure for that?

--DMS

#1 lore raw
Quoted 9 lines · Somashekara DM

Hi,

We want to mount jffs2 on two mtd partitions as a part of our project. Our platform is x86 - kernel version 2.4.13.

1. We are using mtdram ("Test driver using RAM") and blkmtd ("MTD emulation using block device")
to create two mtd's. Our aim is to mount jffs2 on two different
mtds.

OK. So you have two MTD devices listed in /proc/mtd?

Quoted 5 lines

Here are the steps we have followed.

Step1 :

    mknod /dev/mtd0 c 90 0
    mknod /dev/mtd2 c 90 2

This is incorrect. The MAKEDEV script in CVS is correct. The device numbers for the character devices alternate between 'normal' and read-only devices, as follows:

	/dev/mtd0	c 90 0
	/dev/mtdr0	c 90 1
	/dev/mtd1	c 90 2
	/dev/mtdr1	c 90 3
	/dev/mtd2	c 90 4
	/dev/mtdr2	c 90 5

So what you've called '/dev/mtd2' is in fact what _should_ be called '/dev/mtd1', and is hence the second of the two MTD devices (In fact, /dev/mtd2 would be a _third_ device, which does not exist in your system).

Quoted 3 lines

and
mknod /dev/mtdblock0 b 31 0
mknod /dev/mtdblock2 b 31 2

These are correct device numbers and names but as before, /dev/mtdblock2 refers to a third MTD device which does not exist in your system. Make /dev/mtdblock1 (b 31 1) and use that.

Quoted 2 lines

mount -t jffs2 /dev/mtdblock2 /mnt/jffs2drive2 //this mount fails
error - "mount: fs type jffs2 not supported by kernel"

What it actually means is 'block device /dev/mtdblock2 does not exist'. But mount(2) doesn't return sensible errors.

Quoted 2 lines

2. Can we create multiple partitions on the 'mtdram'? Can you give us the procedure for that?

No partitions, but you can load the mtdram module twice (with different names) so that you get two devices.

Signature · 1 line
dwmw2
#2 lore raw

Re: Two questions on mtds on x86 platform - multiple mtdram

Quoted 47 lines · David Woodhouse <dwmw2 <at> infradead.org> writes:
Quoted 9 lines · Somashekara DM

Hi,

We want to mount jffs2 on two mtd partitions as a part of our project. Our platform is x86 - kernel version 2.4.13.

1. We are using mtdram ("Test driver using RAM") and blkmtd ("MTD emulation using block device")
to create two mtd's. Our aim is to mount jffs2 on two different
mtds.

OK. So you have two MTD devices listed in /proc/mtd?

Quoted 5 lines

Here are the steps we have followed.

Step1 :

    mknod /dev/mtd0 c 90 0
    mknod /dev/mtd2 c 90 2

This is incorrect. The MAKEDEV script in CVS is correct. The device numbers for the character devices alternate between 'normal' and read-only devices, as follows:

	/dev/mtd0	c 90 0
	/dev/mtdr0	c 90 1
	/dev/mtd1	c 90 2
	/dev/mtdr1	c 90 3
	/dev/mtd2	c 90 4
	/dev/mtdr2	c 90 5

So what you've called '/dev/mtd2' is in fact what _should_ be called '/dev/mtd1', and is hence the second of the two MTD devices (In fact, /dev/mtd2 would be a _third_ device, which does not exist in your system).

Quoted 3 lines

and
mknod /dev/mtdblock0 b 31 0
mknod /dev/mtdblock2 b 31 2

These are correct device numbers and names but as before, /dev/mtdblock2 refers to a third MTD device which does not exist in your system. Make /dev/mtdblock1 (b 31 1) and use that.

Quoted 2 lines

mount -t jffs2 /dev/mtdblock2 /mnt/jffs2drive2 //this mount fails
error - "mount: fs type jffs2 not supported by kernel"

Quoted 9 lines

What it actually means is 'block device /dev/mtdblock2 does not exist'. But mount(2) doesn't return sensible errors.

Quoted 2 lines

2. Can we create multiple partitions on the 'mtdram'? Can you give us the procedure for that?

No partitions, but you can load the mtdram module twice (with different names) so that you get two devices.

Does this mean that in order to create several mtd devices on mtdram, I can just create several device nodes with different minor device numbers ?

If so, I presume this means that all devices must share the same size and erasesize ?

Regards,
Mike

....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................ ....gmane.padding........................................................