Skip to contentSkip to conversation

linuxppc on dsp-board

DISCUSSION Guenther SOMMER 3 participants 4 messages Mar 14, 2003 – Mar 17, 2003

lore
Share & tools
lore
#0 lore raw

hi!

i'd like to start linux on a dsp-board (where no linux has gone before :)))

it's a dsp-board with some dsp on board an a motorola 860 processor. the board itself has 32mb sdram and 8 mb flash. the board has a bootloader integrated, which configures the mpcs and start a simple "boot-aplication".

normal vxworks is used, but it's time to start something useful now :)))

i'd like this bootapplication to start linux, but how can i do this. the bootloader itself should stay, because it does the initialization.

i didn't find anything like ROLO (a rom-bootloader for linux, but only for x86). ppcboot is a total overkill, because the board is complete initalized, i only need something to start the kernel (no config, no transfer of images, no..., only kick the kernel, which lies mapped in memory from the flash).

the other problem is, which setting for the "board type" in the linux-kernel itself should (kernel from ELDK at www.denx.de) be used?

hope you can give me some tips, i'd like to show my boss, that linux runs everywhere!

greetings, guenther sommer.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw
Quoted 6 lines

i'd like to start linux on a dsp-board (where no linux has gone before :)))

it's a dsp-board with some dsp on board an a motorola 860 processor. the board itself has 32mb sdram and 8 mb flash. the board has a bootloader integrated, which configures the mpcs and start a simple "boot-aplication".

i didn't write it straightforward. i mean it should run on the control-processor (the mpc860), not on the dsps itself. but i think it would be cool, if linux lets the "dsp-dolls" dance :)

grettings, guenther sommer.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#2 lore raw

I've actually run Linux on a hardware that might be something like yours, but it was 3 years ago now. A 2.2-kernel.
The board we used had a 860 and a Texas DSP + some kind of FPGA, great for telecommunications...
I wrote a small piece of boot software that could be compiled to be placed in the internal DPRAM by a BDM or be burned into flash. The boot software then started a zImage from ram or from flash.

I would suggest you to burn a zImage.embedded into the flash.

/ magnus

Quoted 7 lines · On Sat, 15 Mar 2003 00:12:59 +0100 Guenther SOMMER <[email protected]> wrote:
Quoted 6 lines

i'd like to start linux on a dsp-board (where no linux has gone before :)))

it's a dsp-board with some dsp on board an a motorola 860 processor. the board itself has 32mb sdram and 8 mb flash. the board has a bootloader integrated, which configures the mpcs and start a simple "boot-aplication".

Quoted 8 lines

i didn't write it straightforward. i mean it should run on the control-processor (the mpc860), not on the dsps itself. but i think it would be cool, if linux lets the "dsp-dolls" dance :)

grettings, guenther sommer.

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#3 lore raw
In reply to Guenther SOMMER
Quoted 3 lines · Guenther SOMMER

it's a dsp-board with some dsp on board an a motorola 860 processor. the board itself has 32mb sdram and 8 mb flash. the board has a bootloader integrated, which configures the mpcs and start a simple "boot-aplication".

It sounds like you would want the code inside of arch/ppc/boot/, with a more or less empty 'embed_config' function.

--
Tom Rini
http://gate.crashing.org/~trini/

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/