Question about hdparm & dma.
root@war:~# hdparm -X69 /dev/hda /dev/hda: setting xfermode to 69 (UltraDMA mode5) root@war:~# dmesg | tail -n 1 ide0: Speed warnings UDMA 3/4/5 is not functional. root@war:~#
war@war:~$ dmesg|grep -i ST[0-9] hda: ST3120024A, ATA DISK drive war@war:~$
This is a Segeate 120GB 7200RPM drive.
On a:
SIS5513: IDE controller on PCI bus 00 dev 15
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
When I put the drive on a Promise Ultra ATA/133 board, it runs UDMA MODE 5 (ATA 100) just fine.
Next...
When I run hdparm -t /dev/hda on the SiS (with the settings I have shown):
root@war:~# hdparm -v /dev/hda
/dev/hda:
multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) readonly = 0 (off) readahead = 8 (on)
geometry = 14593/255/63, sectors = 234441648, start = 0
root@war:~#
root@war:~# hdparm -t /dev/hda /dev/hda: Timing buffered disk reads: 64 MB in 1.60 seconds = 40.00 MB/sec
Now...
My question is, how is it possible to get > 33MB/s in only UDMA Mode 2 (the linux driver only supports up to UDMA2).
I haven't been able to figure it out.
With the same settings for the promise, and the promise, ide2=ata100 works on the command line, on the SiS/for the SiS, it does not, says it is an invalid option, doing that or setting the dma on manually, I get the same speed (MB/s), but is it really running at ATA/100? I mean, if it is running in UDMA MODE 5 vs UDMA MODE 2, I would assume a little bit of a speed boost, I remember with an older box, going from ATA/66 -> ATA/100 increase about 2-3MB/s throughput with hdparm.
However, more importantly, when I am doing many things simultaenously, I notice a slowdown, I did *NOT* notice this slow down on my older p3/866 + ata/66 system, and I knew for a fact it was at ata/66, not only this, it was a via/133 chipset and the ide[0|1]=ata66 worked as well.
So basically I am wondering if udma mode 5 will be supported for SIS chipsets.
Secondly, I also have one of those Promise/Serial ATA raid on the motherboard (2 serial ata/1 ata133), but that is not supported at all.
So what should I do if I want to run at UDMA MODE 5?
Should I buy another promise controller (ATA/133 PCI) and run it off of that?
Anyone have any suggestions? Please let me know, thank you. Please cc me as I am not on the list.
Quoted 2 lines · Justin Piszcz
My question is, how is it possible to get > 33MB/s in only UDMA Mode 2 (the linux driver only supports up to UDMA2).
You can overclock things if you have the setup wrong.
Quoted 2 lines
So basically I am wondering if udma mode 5 will be supported for SIS chipsets.
I'm wondering if SiS are ever going to provide useful documentation. SiS won't deal with individuals only companies which complicates matters
Quoted 2 lines
Secondly, I also have one of those Promise/Serial ATA raid on the motherboard (2 serial ata/1 ata133), but that is not supported at all.
That may change if things go ok.
Quoted 4 lines · Alan Cox
Quoted 2 lines · Justin Piszcz
My question is, how is it possible to get > 33MB/s in only UDMA Mode 2 (the linux driver only supports up to UDMA2).
Quoted 8 lines
You can overclock things if you have the setup wrong.
Quoted 2 lines
So basically I am wondering if udma mode 5 will be supported for SIS chipsets.
I'm wondering if SiS are ever going to provide useful documentation. SiS won't deal with individuals only companies which complicates matters
Well, if you're not getting good docs from SiS I commend you on your abilities. My P4S533 (SiS645DX chipset) is doing decently well with a Maxtor ATA/133 100G drive. It's only a 5400rpm drive and nearly matches the 120G WD ATA/100 7200rpm in my Dell for hdparm speeds. I was a little disappointed in the speed comparisons till I saw that you're doing this blind.
Thanks.
Signature · 1 line
Murray J. Root