Skip to contentSkip to conversation

firewall startup script

DISCUSSION Felix Bauer 2 participants 3 messages Aug 1, 2003

lore
Share & tools
lore
#0 lore raw

Hi,

if got a question about my script for my router-configuration. It should enable ip4warding, masquerade my local hosts, allow my local hosts everything and open some ports which should be external available but if I run this script it kinda stops after masquerading (I can read the output on the console but then everything is freezed since the local ports aren't open anymore and not reopend by the script). Is there any logical error I missed?

<script>
#!/bin/bash
#** $Id$
#**
#** Firewall-startup script
#**

#** variables
iptables="/sbin/iptables"
localnet="192.168.0.0/24"
worldports="21 22 53 80"

case $1 in
start)
#** enable IP-forwarding
echo "Enabling IP-Forwarding"
echo "1" > /proc/sys/net/ipv4/ip_forward

#** flush old chains
echo "Flushing old rules"
$iptables -F INPUT
$iptables -F OUTPUT
$iptables -F FORWARD
$iptables -t nat -F PREROUTING
$iptables -t nat -F POSTROUTING
$iptables -t nat -F OUTPUT

#** allow localnet everything
echo "Creating rule for local network" $iptables -A INPUT -s localhost -d localhost -j ACCEPT $iptables -A INPUT -p tcp -s $localnet -j ACCEPT $iptables -A INPUT -p udp -s $localnet -j ACCEPT

#** setup Masquerading
echo "Creating rule for Masquerading" $iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE

#** opening ports
echo "Opening ports:"
$iptables -A INPUT -p icmp -j ACCEPT

for port in $worldports
do
echo " - $port"
$iptables -A INPUT -p tcp --dport $port -j ACCEPT $iptables -A INPUT -p udp --dport $port -j ACCEPT
done

#** Allow all outgoing packets to be not filtered
$iptables --policy OUTPUT ACCEPT

#** Drop everything else
$iptables -A INPUT -j DROP
;;
stop)
;;
*)
echo "Usage: $0 { start | stop }"
;;
esac
exit 0
</script>

thx a lot
fe

#1 lore raw
Quoted 12 lines · Felix Bauer

Hi,

if got a question about my script for my router-configuration. It should enable ip4warding, masquerade my local hosts,
allow my local hosts everything and open some ports which should be external available but if I run this script
it kinda stops after masquerading (I can read the output on the console but then everything is freezed since the local
ports aren't open anymore and not reopend by the script). Is there any logical error I missed?

Quoted 7 lines

...

#** setup Masquerading
echo "Creating rule for Masquerading" $iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE

...

You have to open a internetconnection and than pick up the ip-adress for ppp0 from ifconfig and use it for ppp0. After this act you can start your firewall.

Regards,
Ruprecht

-----------------------------------------------
Ruprecht Helms IT-Service & Softwareentwicklung

Tel./Fax +49[0]7621 16 99 16

Homepage: http://www.rheyn.de
email:    [email protected]

------------------------------------------------

#2 lore raw

There is a internetconnection of course and ppp0 uses that ip-adress.

cheers
fe

Quoted 53 lines · Ruprecht Helms
Quoted 26 lines · Felix Bauer

Hi,

if got a question about my script for my router-configuration. It should enable ip4warding, masquerade my local hosts, allow my local hosts everything and open some ports which should be external available but if I run this script it kinda stops after masquerading (I can read the output on the console but then everything is freezed since the local ports aren't open anymore and not reopend by the script). Is there any logical error I missed?

...

#** setup Masquerading
echo "Creating rule for Masquerading" $iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE

Quoted 3 lines

...

You have to open a internetconnection and than pick up the ip-adress for ppp0 from ifconfig and use it for ppp0. After this act you can start your firewall.

Regards,
Ruprecht

-----------------------------------------------
Ruprecht Helms IT-Service & Softwareentwicklung

Tel./Fax +49[0]7621 16 99 16

Homepage: http://www.rheyn.de
email:    [email protected]

------------------------------------------------