unexpected IO-APIC
Hey Kernel people!
I noticed this line in my kernel startup.
Attached is my whole dmesg output.
I'm using: Linux parker 2.4.21 #2 SMP Tue Aug 12 11:26:18 EDT 2003 i686 unknown
The system is a brand new Dell Optiplex GX270 dual p4
I'm more than willing to help provide any more details of my system and would be willing to perform any debugging that you'd like.
-- Tom Parker
Linux version 2.4.21 (root@parker) (gcc version 3.2.2) #2 SMP Tue Aug 12 11:26:18 EDT 2003 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff70000 (usable)
BIOS-e820: 000000001ff70000 - 000000001ff72000 (ACPI NVS)
BIOS-e820: 000000001ff72000 - 000000001ff93000 (ACPI data)
BIOS-e820: 000000001ff93000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 130928
zone(0): 4096 pages.
zone(1): 126832 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00feba0
RSD PTR v0 [DELL ]__va_range(0xfd194, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [DELL GX270 0.6]__va_range(0xfd1cc, 0x24): idx=8 mapped at ffff6000__va_range(0xfd1cc, 0x74): idx=8 mapped at ffff6000
ACPI table found: FACP v1 [DELL GX270 0.6]__va_range(0xfffd0144, 0x24): idx=8 mapped at ffff6000 __va_range(0xfffd0144, 0xba): idx=8 mapped at ffff6000
ACPI table found: SSDT v1 [DELL st_ex 0.4096]__va_range(0xfd240, 0x24): idx=8 mapped at ffff6000__va_range(0xfd240, 0x6c): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [DELL GX270 0.6]__va_range(0xfd240, 0x6c): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0001] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16
LAPIC (acpi_id[0x0002] id[0x1] enabled[1])
CPU 1 (0x0100) enabledProcessor #1 Pentium 4(tm) XEON(tm) APIC version 16
LAPIC (acpi_id[0x0003] id[0x1] enabled[0])
CPU 2 (0x0100) disabled
LAPIC (acpi_id[0x0004] id[0x3] enabled[0])
CPU 3 (0x0300) disabled
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
4 CPUs total
Local APIC address fee00000__va_range(0xfd2ac, 0x24): idx=8 mapped at ffff6000__va_range(0xfd2ac, 0x28): idx=8 mapped at ffff6000
ACPI table found: BOOT v1 [DELL GX270 0.6]__va_range(0xfd2d4, 0x24): idx=8 mapped at ffff6000__va_range(0xfd2d4, 0x67): idx=8 mapped at ffff6000
ACPI table found: ASF! v16 [DELL GX270 0.6]
ACPI: Unsupported table ASF!
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: Opti GX270 APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Kernel command line: BOOT_IMAGE=linux2.4 root=305
Initializing CPU#0
Detected 2394.051 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4771.02 BogoMIPS
Memory: 514732k/523712k available (1710k kernel code, 8596k reserved, 602k data, 116k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09 per-CPU timeslice cutoff: 1462.29 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4784.12 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Total of 2 processors activated (9555.14 BogoMIPS). cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-13, 2-20, 2-21, 2-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 41.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] .... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 0 0 0 0 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 0 0 0 0 0 1 1 71 0a 003 03 0 0 0 0 0 1 1 79 0b 003 03 0 0 0 0 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 000 00 1 0 0 0 0 0 0 00 0e 003 03 0 0 0 0 0 1 1 91 0f 003 03 0 0 0 0 0 1 1 99 10 003 03 1 1 0 1 0 1 1 A1 11 003 03 1 1 0 1 0 1 1 A9 12 003 03 1 1 0 1 0 1 1 B1 13 003 03 1 1 0 1 0 1 1 B9 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 003 03 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2394.1023 MHz.
..... host bus clock speed is 199.5083 MHz.
cpu: 0, clocks: 1995083, slice: 665027 CPU0<T0:1995072,T1:1330016,D:29,S:665027,C:1995083>
cpu: 1, clocks: 1995083, slice: 665027 CPU1<T0:1995072,T1:665008,D:10,S:665027,C:1995083>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfbabb, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router default [8086/24d0] at 00:1f.0PCI->APIC IRQ transform: (B0,I29,P0) -> 16PCI->APIC IRQ transform: (B0,I29,P1) -> 19PCI->APIC IRQ transform: (B0,I29,P2) -> 18PCI->APIC IRQ transform: (B0,I29,P0) -> 16PCI->APIC IRQ transform: (B0,I29,P3) -> 23PCI->APIC IRQ transform: (B0,I31,P0) -> 18PCI->APIC IRQ transform: (B0,I31,P0) -> 18PCI->APIC IRQ transform: (B0,I31,P1) -> 17PCI->APIC IRQ transform: (B0,I31,P1) -> 17PCI->APIC IRQ transform: (B1,I0,P0) -> 16PCI->APIC IRQ transform: (B2,I12,P0) -> 18
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 [email protected]).
NTFS driver v1.1.22 [Flags: R/O]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Intel(R) PRO/1000 Network Driver - version 5.0.43-k1
Copyright (c) 1999-2003 Intel Corporation.
eth0: Intel(R) PRO/1000 Network Connection
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Unsupported Intel chipset (device id: 2570), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pioICH5-SATA: IDE controller at PCI slot 00:1f.2
ICH5-SATA: chipset revision 2
ICH5-SATA: 100% native mode on irq 18
ICH5-SATA: neither IDE port enabled (BIOS)
hda: Maxtor 6E040L0, ATA DISK drive
blk: queue c03bd740, I/O limit 4095Mb (mask 0xffffffff)
hdc: MATSHITA CD-RW UJDA360, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=4998/255/63, UDMA(100)
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 >
Intel 810 + AC97 Audio, version 0.24, 11:21:53 Aug 12 2003
es1371: version v0.32 time 11:22:00 Aug 12 2003usb.c: registered new driver hubhost/uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64host/uhci.c: USB UHCI at I/O 0xff80, IRQ 16usb.c: new USB bus registered, assigned bus number 1hub.c: USB hub foundhub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64host/uhci.c: USB UHCI at I/O 0xff60, IRQ 19usb.c: new USB bus registered, assigned bus number 2hub.c: USB hub foundhub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64host/uhci.c: USB UHCI at I/O 0xff40, IRQ 18usb.c: new USB bus registered, assigned bus number 3hub.c: USB hub foundhub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64host/uhci.c: USB UHCI at I/O 0xff20, IRQ 16usb.c: new USB bus registered, assigned bus number 4hub.c: USB hub foundhub.c: 2 ports detectedusb.c: registered new driver hidhid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 116k freedhub.c: new USB device 00:1d.0-2, assigned address 2hub.c: USB hub foundhub.c: 3 ports detected
Adding Swap: 1020088k swap-space (priority -1)hub.c: new USB device 00:1d.0-2.1, assigned address 3
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
e1000: eth0 NIC Link is Up 100 Mbps Half Duplex
usb_control/bulk_msg: timeout
input0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard Hub] on usb1:3.0
input1: USB HID v1.10 Pointer [Dell Dell USB Keyboard Hub] on usb1:3.1hub.c: new USB device 00:1d.0-2.3, assigned address 4
input2: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb1:4.0
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul 16 19:03:09 PDT 2003 1: NVRM: AGPGART: unable to retrieve symbol table