How to choose between ip 2 identical ethernet cards
Sorry for a bit off topic.
I have a Dell 8200 laptop and a docking station, both with 3c905C ethenet chips. I wish to use the 3c905c internal to the docking station when the system is docked. Otherwise the 3c905c internal to the 8200. In my office I would like to run with both eth0 and eth1, but I need to be able to connect the correct interface to the correct cable. The same module is loaded for both devices.
The HOWTOs I found all assumed you had old cards with fixed addresses. These could be specified as options in modules.conf. From the Net-HOWTO:
alias eth0 ne
alias eth1 ne
alias eth2 ne
options ne io=0x220,0x240,0x300
But this does not seem to apply to the 3c59x driver. modinfo doesn't even list "io" as a valid option.
I did find:
1) in /proc/ioports, one of the devices is listed with "(#2)" after it.
2) in /etc/sysconfig/hwconf, one of the devices has
subDeviceId = 00d4, the other 00de.
I have tried changing the order of loading modules, along with a few vain attempts in modules.conf. For info, this is a Redhat system. Where is the definition as to which device will be associated with eth0 made?
Any assistance would be appreciated. I did try to RTFM, I just can't find the correct "fine manual";-) thanks
don
-------------------------------------------------------------------
| Don Fisher [email protected] | | Steward Observatory | | 933 N. Cherry Ave. VOICE: (520)621-7647 | | University of Arizona FAX: (520)621-9843 | | Tucson, AZ 85721 |
-------------------------------------------------------------------
Signature · 3 lines
redhat-list mailing list unsubscribe mailto:[email protected]?subject=unsubscribe https://www.redhat.com/mailman/listinfo/redhat-list
Quoted 4 lines · don fisher
I have tried changing the order of loading modules, along with a few vain attempts in modules.conf. For info, this is a Redhat system. Where is the definition as to which device will be associated with eth0 made?
'man nameif'
Works great, less filling - my Dell 840 has up to *4* ethernets (the onboard built-in, the dock, the built-in wireless, and a Xircom card that's a combo 56k modem/100BaseT).
My /etc/mactab looks like this:
# Onboard 10/100 port
eth0 00:06:5b:b9:5e:27
# 10/100 port on Xircom 10/100/56K card
eth2 00:10:a4:9c:a8:86
# wireless card wvlan0 00:02:2d:5c:11:48 eth1 00:02:2d:5c:11:48 # 10/100 port on dock... eth3 00:06:5b:ea:8e:4e
(yes, there's 2 entries for the wireless - 2.4 kernel wants wvlanX, 2.6 calls it ethX.
The magic under a RedHat system happens in:
/etc/sysconfig/network-scripts/ifup
Hope that helps.
Quoted 9 lines
On Fri, 29 Aug 2003 17:29:29 PDT, don fisher
<[email protected]> said:The magic under a RedHat system happens in:
/etc/sysconfig/network-scripts/ifupHope that helps.
Yep, quite painless. Just specify the mac address in the 'ifcfg-<name>'
configuration file.
DS
On Fri, 29 Aug 2003 17:29:29 -0700 don fisher <[email protected]> wrote:
| Sorry for a bit off topic. | | I have a Dell 8200 laptop and a docking station, both with 3c905C | ethenet chips. I wish to use the 3c905c internal to the docking | station when the system is docked. Otherwise the 3c905c internal to | the 8200. In my office I would like to run with both eth0 and eth1, | but I need to be able to connect the correct interface to the correct | cable. The same module is loaded for both devices. | | The HOWTOs I found all assumed you had old cards with fixed addresses. | These could be specified as options in modules.conf. From the Net-HOWTO: | alias eth0 ne | alias eth1 ne | alias eth2 ne | options ne io=0x220,0x240,0x300 | But this does not seem to apply to the 3c59x driver. modinfo doesn't | even list "io" as a valid option. | | I did find: | 1) in /proc/ioports, one of the devices is listed with "(#2)" after it. | 2) in /etc/sysconfig/hwconf, one of the devices has | subDeviceId = 00d4, the other 00de. | | I have tried changing the order of loading modules, along with a few | vain attempts in modules.conf. For info, this is a Redhat system. | Where is the definition as to which device will be associated with | eth0 made? | | Any assistance would be appreciated. I did try to RTFM, I just can't | find the correct "fine manual";-) | thanks | don
I did a mini-howto for 'nameif'. URL is below. Maybe it can help you.
http://www.xenotime.net/linux/doc/network-interface-names.txt
--
~Randy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
On Fri, 29 Aug 2003 17:29:29 -0700 don fisher <[email protected]> wrote:
| Sorry for a bit off topic. | | I have a Dell 8200 laptop and a docking station, both with 3c905C | ethenet chips. I wish to use the 3c905c internal to the docking | station when the system is docked. Otherwise the 3c905c internal to | the 8200. In my office I would like to run with both eth0 and eth1, | but I need to be able to connect the correct interface to the correct | cable. The same module is loaded for both devices. | | The HOWTOs I found all assumed you had old cards with fixed addresses. | These could be specified as options in modules.conf. From the Net-HOWTO: | alias eth0 ne | alias eth1 ne | alias eth2 ne | options ne io=0x220,0x240,0x300 | But this does not seem to apply to the 3c59x driver. modinfo doesn't | even list "io" as a valid option. | | I did find: | 1) in /proc/ioports, one of the devices is listed with "(#2)" after it. | 2) in /etc/sysconfig/hwconf, one of the devices has | subDeviceId = 00d4, the other 00de. | | I have tried changing the order of loading modules, along with a few | vain attempts in modules.conf. For info, this is a Redhat system. | Where is the definition as to which device will be associated with | eth0 made? | | Any assistance would be appreciated. I did try to RTFM, I just can't | find the correct "fine manual";-) | thanks | don
I did a mini-howto for 'nameif'. URL is below. Maybe it can help you.
http://www.xenotime.net/linux/doc/network-interface-names.txt
--
~Randy