Probably buggy MP Table and ACPI doesn't works

Hi, I've compiled my kernel with Local APIC and IO-APIC function on a UniProcessor system (MSI KT4 Ultra + Athlon 2400+) and at the system start I see this (kernel 2.4.21-pre3-ac4 , but is similar with all the kernels) :

Linux version 2.4.21-pre3-ac4 (root@valinor) (gcc version 3.2.2 20030109 (Debian prerelease)) #1 ven set 12 00:56:30 CEST 2003 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000fb930
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 3 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: auto BOOT_IMAGE=Linux ro root=305 video=vesa:ywrap,mtrr
Initializing CPU#0
Detected 2000.130 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 3984.58 BogoMIPS
Memory: 516224k/524224k available (1192k kernel code, 7612k reserved, 412k data, 104k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:             Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2400+ stepping 01

Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-17, 2-18, 2-20, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178003

.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0003

An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] .... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00

01 001 01  0    0    0   0   0    1    1    39
02 001 01  0    0    0   0   0    1    1    31
03 001 01  0    0    0   0   0    1    1    41
04 001 01  0    0    0   0   0    1    1    49
05 000 00  1    0    0   0   0    0    0    00
06 001 01  0    0    0   0   0    1    1    51
07 001 01  0    0    0   0   0    1    1    59
08 001 01  0    0    0   0   0    1    1    61
09 000 00  1    0    0   0   0    0    0    00
0a 000 00  1    0    0   0   0    0    0    00
0b 000 00  1    0    0   0   0    0    0    00
0c 001 01  0    0    0   0   0    1    1    69
0d 001 01  0    0    0   0   0    1    1    71
0e 001 01  0    0    0   0   0    1    1    79
0f 001 01  0    0    0   0   0    1    1    81
10 001 01  1    1    0   1   0    1    1    89
11 000 00  1    0    0   0   0    0    0    00
12 000 00  1    0    0   0   0    0    0    00
13 001 01  1    1    0   1   0    1    1    91
14 000 00  1    0    0   0   0    0    0    00
15 001 01  1    1    0   1   0    1    1    99
16 000 00  1    0    0   0   0    0    0    00
17 000 00  1    0    0   0   0    0    0    00

IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ19 -> 0:19
IRQ21 -> 0:21
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2000.2553 MHz.
..... host bus clock speed is 266.7008 MHz.
cpu: 0, clocks: 2667008, slice: 1333504 CPU0<T0:2667008,T1:1333504,D:0,S:1333504,C:2667008>
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I7,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 16
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P2) -> 21
PCI->APIC IRQ transform: (B0,I16,P3) -> 21
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.2, from 10 to 5
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
PnPBIOS: Found PnP BIOS installation structure at 0xc00f79a0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x686b, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
ACPI: Core Subsystem version [20011018]
ACPI: Subsystem enabled
vesafb: framebuffer at 0xd8000000, mapped to 0xe0807000, size 65536k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: protected mode interface info at c000:b7d0
vesafb: pmi: set display start = c00cb815, set palette = c00cb89a
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=16384
vesafb: directcolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
PCI: No IRQ known for interrupt pin A of device 00:11.1. Probably buggy MP table.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALLP AS30.0, ATA DISK drive
hdb: MAXTOR 6L060J3, ATA DISK drive
hda: DMA disabled
blk: queue c02d8860, I/O limit 4095Mb (mask 0xffffffff)
hdb: DMA disabled
blk: queue c02d899c, I/O limit 4095Mb (mask 0xffffffff)
hdc: _NEC DV-5800A, ATAPI CD/DVD-ROM drive
hdd: Hewlett-Packard CD-Writer Plus 8100, ATAPI CD/DVD-ROM drive
hdc: DMA disabled
hdd: DMA disabled
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 58633344 sectors (30020 MB) w/1902KiB Cache, CHS=3649/255/63, UDMA(100)
hdb: host protected area => 1
hdb: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=7299/255/63, UDMA(133)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 > /dev/ide/host0/bus0/target1/lun0: p1 p2 p3 < p5 > p4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
reiserfs: checking transaction log (device 03:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 104k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 506036k swap-space (priority -1)
Adding Swap: 506036k swap-space (priority -2)
IA-32 Microcode Update Driver: v1.11 <[email protected]>
i2c-core.o: i2c core module
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe4952f00, 00:40:f4:55:a1:40, IRQ 19
eth0: Identified 8139 chip type 'RTL-8139C'
Power Resource: found
Power Resource: found
Power Resource: found
Power Resource: found
ACPI: Power Button (FF) found
ACPI: Multiple power buttons detected, ignoring fixed-feature
ACPI: Power Button (CM) found
ACPI: Sleep Button (CM) found
ACPI: System firmware supports S0 S1 S4 S5
Processor[0]: C0 C1, 8 throttling states
Non-volatile memory driver v1.2
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices

 Vendor: _NEC      Model: DV-5800A          Rev: 1.90
 Type:   CD-ROM                             ANSI SCSI revision: 02
 Vendor: HP        Model: CD-Writer+ 8100   Rev: 1.0g
 Type:   CD-ROM                             ANSI SCSI revision: 02

cmpci: version $Revision: 5.64 $ time 01:00:52 Sep 12 2003
cmpci: found CM8738 adapter at io 0xe800 irq 16
cmpci: chip version = 055
cmpci: Inverse SPDIF-in
cmpci: Enable SPDIF loop
arp_tables: (C) 2002 David S. Miller
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ASSERT ip_conntrack_core.c:624 &ip_conntrack_lock not readlocked
ASSERT ip_conntrack_core.c:624 &ip_conntrack_lock not readlocked
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7
ide: no cache flush required.
ide: no cache flush required.
ide: no cache flush required.
ide: no cache flush required.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
reiserfs: checking transaction log (device 03:01) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:06) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,68), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,69), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ide: no cache flush required.
ide: no cache flush required.
eth0: Setting half-duplex based on auto-negotiated partner ability 0000. detected

What does mean buggy MP table on device 00.11.1 ?? (That is the IDE controller I think) In my bios I can select 1.4. and 1.1. MPS table, I've tried both but the situation doesn't change. This messsage is appeared recently , with the bios upgrade from 1.1 to 1.3. Doing lspci -vvvxxx I've noticed that the IRQ of 00.11.1 is routed to IRQ 0 .

And there is another problem. With IO-APIC activated in the kernel ACPI works in a strange way. I can't shutdown the system by pressing the On/Off button, and when I do "shutdown -h now" the system instead to halt it reboots . I hear the HD that are Off, but the fans and the PSU remain Switch On, after few seconds the HDs switch on again and the system restarts. Why??

If I disable IO-APIC and use Local APIC only ACPI works correctly, but I recive the message "spurious 8259A interrupt: IRQ7" during the boot or few time later after the boot. Should I disable APIC at all?? This problem of ACPI is present with 1.1 bios too

Thanks

Bye

Marcello

Ooops , thank you very much! :-D

You are right!

Anyone have an idea about this?

Byez

I was thinking of an entirely new model for partitionable block devices. Here is how it would work:

Each physical disk would be assigned a minor number in a group of majors. So assume a major was chosen of 150, 151, 152, 153, there would be a total of 1024 physical disks that could be mapped. Then the device mapper code could be used to provide partition devices in another major/group of majors.

The advantage of this technique is that instead of wasting tons of minors on partitions that are never used, partitions could be dynamically allocated out of the minor list, allowing for thousands of disks with varying numbers of partitions each. Further instead of each block device (such as i2o, scsi, etc) having their own set of majors for each partitionable disk (which wastes dev_t address space) everything would be compressed into the same set of majors.

As an example, Lets assume we want 4096 total disks with 16384 total partitions (4 partitions per disk, where it is likely to be less):

That is:
4096 disks / 256 disks * 1 major = 16 majors 16384 partitions / 256 partitions * 1 major = 64 majors total of 80 majors

To allow a similiar configuration in the current block device setup, with just the SCSI disk major, 4096 disks / 16 disks * 1 major = 256 majors

Now, assume we have 4096 disks available for i2o, scsi, compaq raid, etc etc, we are talking about lots of majors that go way beyond the current addressable 16 bytes.

The only downside is addressing the disks in hotswap (ie: how do you know what disk is where?) This can be achieved through per-subsystem devfs mapping (ie: linking /dev/scsi/hostX/... to /dev/disc0) or userspace utilities that scan the disk devices (such as those that would be in /dev/disk) and determine which disks are what.

Thanks
-steve

This sounds suspiciously like the already-existing device mapper stuff used by LVM2. Maybe all that's needed is to add a hook to add a device mapper entry for each partition?

				Valdis Kletnieks
				Computer Systems Senior Engineer
				Virginia Tech

For newer revs of linux, I was specifically thinking of implementing using device mapper to provide partition mapping so your thinking just like me :) The only downside is device mapper becomes a required component instead of being module capable since partition information is needed before early boot is available to load modules.

Regards,
-steve

Great idea! Add another partition, and the minors for everything else on the system change. Not!

Dr. Horst H. von Brand                   User #22616 counter.li.org
Departamento de Informatica                     Fono: +56 32 654431
Universidad Tecnica Federico Santa Maria              +56 32 654239
Casilla 110-V, Valparaiso, Chile                Fax:  +56 32 797513

It isn't minors that shouldn't change, it is the mapping of the filesystem device node to those minors. This can be achieved by properly managing device naming in userspace automatically on partition updates, instead of using static naming such as /dev/sda which already has significant problems when devices are removed/inserted in hotswap environments.

The fact that minors change is irrelevant if proper steps are taken to ensure that those minors always map to the correct named device in user space.

Thanks
-steve