Skip to contentSkip to conversation

P4C800E-Dlx: ICH5/S-ATA and Intel Pro onboard network incompatibility ?

DISCUSSION Philippe Lochon 6 participants 13 messages Oct 4, 2003 – Oct 10, 2003

lore
Share & tools
lore

Philippe Lochon

author
#0 lore raw

Hi,

I'm running Mandrake 9.2RC1 (kernel 2.4.22) and I can't make work S-ATA boot drive and Intel Pro onboard network.

The Asus P4C800E-Dlx in the only mainboard in the P4x800 family with ICH5R and Intel 82547EI (Gb onboard chip, it uses e1000 driver).

The chips share the same IRQ :

# grep eth0 /proc/interrupts
 17:         83   IO-APIC-level  Intel ICH5, eth0
(note that there's no error about this in syslog)

1) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off"
-> boot OK, but no ping, "NETDEV WATCHDOG: eth0: transmit timed out" in syslog. (full log and config on http://plochon.free.fr/mdk92RC1.html )

2) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off" and "noapic"
-> boot hang (when displays "hde: attached ide_disk driver" where hde is the S-ATA boot drive)

3) Same tests but boot on CD with Knoppix 3.3 (Kernel 2.4.22) -> same results

4) S-ATA drive physically removed, boot on CD / Knoppix 3.3 with "acpi=off" and "noapic" -> boot OK, network OK : it works !

Is there a way to make S-ATA and Intel Pro work together, or is it an incompatibility ?

Thanks,
Philippe

My hardware configuration:
P4C800E-Dlx, [email protected], 256Mb, 1 Seagate S-ATA drive plugged on standard S-ATA connector (-> not on S-ATA RAID connector) IDE Bios settings :
Onboard IDE operate mode : Enhanced mode
Enhanced mode support on : S-ATA
Configure S-ATA as RAID : No

#1 lore raw
Quoted 13 lines · Philippe Lochon

Hi,

I'm running Mandrake 9.2RC1 (kernel 2.4.22) and I can't make work S-ATA boot drive and Intel Pro onboard network.

The Asus P4C800E-Dlx in the only mainboard in the P4x800 family with ICH5R and Intel 82547EI (Gb onboard chip, it uses e1000 driver).

The chips share the same IRQ :

# grep eth0 /proc/interrupts
 17:         83   IO-APIC-level  Intel ICH5, eth0
(note that there's no error about this in syslog)
Quoted 8 lines

1) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off"
-> boot OK, but no ping, "NETDEV WATCHDOG: eth0: transmit timed out" in syslog.
(full log and config on http://plochon.free.fr/mdk92RC1.html )

2) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off" and "noapic" -> boot hang (when displays "hde: attached ide_disk driver" where hde is the S-ATA boot drive)

I have an Asus P4P800 and I see the same thing. I have to enter the BIOS and set IDE to Compatible mode, even with the latest libata. Dunno why, but with the ICH5 in native mode it simply won't boot.

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#2 lore raw
Quoted 19 lines · Erik Andersen
Quoted 18 lines · Philippe Lochon

Hi,

I'm running Mandrake 9.2RC1 (kernel 2.4.22) and I can't make work S-ATA boot drive and Intel Pro onboard network.

The Asus P4C800E-Dlx in the only mainboard in the P4x800 family with ICH5R and Intel 82547EI (Gb onboard chip, it uses e1000 driver).

The chips share the same IRQ :

# grep eth0 /proc/interrupts
 17:         83   IO-APIC-level  Intel ICH5, eth0
(note that there's no error about this in syslog)

1) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off"
-> boot OK, but no ping, "NETDEV WATCHDOG: eth0: transmit timed out" in syslog.
(full log and config on http://plochon.free.fr/mdk92RC1.html )

Quoted 8 lines
Quoted 3 lines

2) Boot on S-ATA drive / Mandrake 9.2RC1 with "acpi=off" and "noapic" -> boot hang (when displays "hde: attached ide_disk driver" where hde is the S-ATA boot drive)

I have an Asus P4P800 and I see the same thing. I have to enter the BIOS and set IDE to Compatible mode, even with the latest libata. Dunno why, but with the ICH5 in native mode it simply won't boot.

Tre weird. Any chance both of you could forward me libata boot/err messages?

There are also debugging controls in include/linux/ata.h which add tons of verbosity to dmesg.

ftp://ftp.kernel.org/pub/linux/kernel/people/jgarzik/libata/ (patches for 2.4 and 2.6)

Jeff

#4 lore raw
Quoted 2 lines · Jeff Garzik

Oh yeah, when ICH5 SATA is configured to native mode, "lspci -vvvxxx" output -- when run as root -- would be helpful as well.

I'd be happy to do that -- if I can get it to boot up in native mode....

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#12 lore raw
In reply to Jeff Garzik
Quoted 3 lines · Jeff Garzik

Oh yeah, when ICH5 SATA is configured to native mode, "lspci -vvvxxx" output -- when run as root -- would be helpful as well.

You can show extended lspci output at http://plochon.free.fr/lspci.txt
IDE Bios setting sets to "Enhanced mode" (what you call "native mode" I presume), but without "noapic" flag (with "nopic" it won't boot).

Philippe

#5 lore raw
In reply to Erik Andersen
Quoted 6 lines · Erik
Quoted 2 lines · Jeff Garzik

Oh yeah, when ICH5 SATA is configured to native mode, "lspci -vvvxxx" output -- when run as root -- would be helpful as well.

I'd be happy to do that -- if I can get it to boot up in native mode....

Ok. I spent some time exploring the problem and made some progress. I noticed it was freezing after running init. So I _was_ able to make it boot into init=/bin/sh and get the lspci output for you (attached).

When I have the Bios set to compatible mode everything works -- except for the obvious problem that I have to put my SATA drive onto my promise SATA card (since the ICH5 SATA is disabled).

When I have the Bios set to Enhanced mode (so the ICH5 provides both SATA and PATA) then my system will wedge solid as a rock.

It turns out it was locking up while loading up the ide-scsi kernel module. I have

options ide-cd ignore='hdc'

in my /etc/modules.conf so my CD/DVD writer (on hdc) can be owned by ide-scsi so cdrecord will talk to it. 2.4.22-pre6 with the latest libata, and Intel SATA disabled in drivers/ide/pci/piix.c so the libata driver will win,

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O Controller (rev 02)

	Subsystem: Asustek Computer, Inc.: Unknown device 80f2
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [e4] #09 [2106]
	Capabilities: [a0] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>

00: 86 80 70 25 06 00 90 20 02 00 00 06 00 00 00 00 10: 08 00 00 f8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f2 80 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 02 08 00 40 80 1c 00 00 00 00 00 00 00 00 00 60: 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 11 11 00 33 33 00 00 00 00 00 00 0a 38 00
a0: 02 00 30 00 1b 4a 00 1f 00 0a 00 00 00 00 00 00
b0: 00 00 00 00 30 00 00 00 00 00 b2 37 20 10 00 00
c0: 00 00 00 00 00 80 0e 20 00 00 00 00 00 00 00 00
d0: 02 28 04 0e 0b 0d 00 00 00 00 00 00 00 00 20 01
e0: 00 00 00 00 09 a0 06 21 00 02 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00

00:01.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to AGP Controller (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: d7e00000-f7dfffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00: 86 80 71 25 07 01 a0 00 02 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 c0 c0 a0 22
20: 90 fe 90 fe e0 d7 d0 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00

00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at eec0 [size=32]
00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: c1 ee 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at ef00 [size=32]
00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ef20 [size=32]
00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 21 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef40 [size=32]
00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00
10: 00 f8 bf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 80
70: 00 00 c5 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 55 55 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 80 00 00 88 83 40 00 66 0f 04 00 06 14 00 00

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: f7e00000-f7efffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 40 d0 d0 80 22
20: a0 fe a0 fe e0 f7 e0 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
40: 02 28 30 76 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 64 73 00 00 00 00 00 50 01 34 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 51 33

00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 10 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 81 04 00 00 10 00 00 00
60: 0a 0e 0b 0f d0 00 00 00 80 0a 07 05 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: ff fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 20 02 00 00 01 00 00 00 0d 00 00 00 00 03 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 84 21 00 00 02 0f 00 00 04 00 00 00 00 00 00 00
e0: 00 00 00 80 00 00 08 14 33 22 11 00 00 00 67 45
f0: 00 00 40 00 04 00 00 00 66 0f 04 1e 00 00 00 00

00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at efe0 [size=8]
Region 1: I/O ports at efac [size=4]
Region 2: I/O ports at efa0 [size=8]
Region 3: I/O ports at efa8 [size=4]
Region 4: I/O ports at ef90 [size=16]
Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K]
00: 86 80 db 24 07 00 80 02 02 8f 01 01 00 00 00 00
10: e1 ef 00 00 ad ef 00 00 a1 ef 00 00 a9 ef 00 00
20: 91 ef 00 00 00 00 00 80 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 77 e3 77 e3 bb 00 00 00 0f 00 11 22 00 00 00 00
50: 00 00 00 00 fb 30 00 00 00 00 00 00 00 00 00 00
60: 08 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.2 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at ef88 [size=8]
Region 1: I/O ports at ef84 [size=4]
Region 2: I/O ports at ef68 [size=8]
Region 3: I/O ports at ef80 [size=4]
Region 4: I/O ports at ee60 [size=16]
00: 86 80 d1 24 05 00 a0 02 02 8f 01 01 00 00 00 00
10: 89 ef 00 00 85 ef 00 00 69 ef 00 00 81 ef 00 00
20: 61 ee 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 07 a3 00 80 00 00 00 00 01 00 01 00 00 00 00 00
50: 00 00 00 00 31 10 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 11 00 20 00 00 00 00 00 00 00 00 00 00 00
a0: 40 00 00 00 43 00 22 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 0400 [size=32]
00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0e 02 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio Controller (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 80f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at febff400 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at febff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00
10: 01 e8 00 00 81 ee 00 00 00 f4 bf fe 00 f0 bf fe
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f3 80
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 02 00 00
40: 09 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 c2 c9 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5961 (rev 01) (prog-if 00 [VGA])

	Subsystem: PC Partner Limited: Unknown device 7c13
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min), cache line size 04
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at c000 [size=256]
	Region 2: Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at fe9c0000 [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00: 02 10 61 59 07 01 b0 02 01 00 00 03 04 40 80 00 10: 08 00 00 e8 01 c0 00 00 00 00 9f fe 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 13 7c 30: 00 00 9c fe 58 00 00 00 00 00 00 00 0a 01 08 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 13 7c 50: 01 00 02 06 00 00 00 00 02 50 30 00 1b 02 00 ff 60: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01:00.1 Display controller: ATI Technologies Inc: Unknown device 5941 (rev 01)
Subsystem: PC Partner Limited: Unknown device 7c12
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 04
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at fe9e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 41 59 07 00 b0 02 01 00 80 03 04 40 00 00
10: 08 00 00 e0 00 00 9e fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 12 7c
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 02 06 00 00 00 00 02 50 30 00 1b 02 00 ff
60: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:05.0 Ethernet controller: 3Com Corporation: Unknown device 1700 (rev 12)
Subsystem: Asustek Computer, Inc.: Unknown device 80eb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), cache line size 04
Interrupt: pin A routed to IRQ 22
Region 0: Memory at feaf8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data
00: b7 10 00 17 17 01 b0 02 12 00 00 02 04 40 00 00
10: 00 80 af fe 01 d8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 eb 80
30: 00 00 00 00 48 00 00 00 00 00 00 00 07 01 17 1f
40: 00 00 b0 05 01 40 a0 01 01 50 02 fe 00 2e 00 0c
50: 03 00 fc 80 00 00 00 78 00 00 04 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:09.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 04
Interrupt: pin A routed to IRQ 21
BIST result: 00
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 05 90 80 00 17 01 b0 02 02 00 00 01 04 40 00 80
10: 01 d4 00 00 04 f0 af fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 05 90 a0 e2
30: 00 00 ac fe dc 00 00 00 00 00 00 00 0a 01 28 19
40: 02 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:0a.0 Multimedia video controller: Brooktree Corporation Bt848 Video Capture (rev 12)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f7eff000 (32-bit, prefetchable) [size=4K]
00: 9e 10 50 03 06 01 80 02 12 00 00 04 00 40 00 00
10: 08 f0 ef f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 01 10 28
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:0b.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), cache line size 04
Interrupt: pin A routed to IRQ 23
Region 0: Memory at feafe800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at feaf4000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 4c 10 20 80 16 01 10 02 00 10 00 0c 04 40 00 00
10: 00 e8 af fe 00 40 af fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 04
40: 00 00 00 00 01 00 11 64 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 10 24 00 00 02 10 00 00 00 00 00 00 00 00 01 01

02:0d.0 Unknown mass storage controller: Promise Technology, Inc.: Unknown device 3375 (rev 02)
Subsystem: Promise Technology, Inc.: Unknown device 3375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), cache line size 04
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at df00 [size=64]
Region 1: I/O ports at dfa0 [size=16]
Region 2: I/O ports at dc00 [size=128]
Region 3: Memory at feafd000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at feaa0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fea90000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 5a 10 75 33 17 01 30 02 02 00 80 01 04 60 00 00
10: 01 df 00 00 a1 df 00 00 01 dc 00 00 00 d0 af fe
20: 00 00 aa fe 00 00 00 00 00 00 00 00 5a 10 75 33
30: 00 00 a9 fe 60 00 00 00 00 00 00 00 0a 01 04 12
40: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 22 02 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 ff ff 03 00 00 00 00 00 00 00 00 00

#6 lore raw
Quoted 11 lines · Erik Andersen

When I have the Bios set to compatible mode everything works -- except for the obvious problem that I have to put my SATA drive onto my promise SATA card (since the ICH5 SATA is disabled).

When I have the Bios set to Enhanced mode (so the ICH5 provides both SATA and PATA) then my system will wedge solid as a rock.

It turns out it was locking up while loading up the ide-scsi kernel module. I have

options ide-cd ignore='hdc'

So, things work in Enchanced mode if ide-scsi module is not loaded?

And, drivers/ide is picking up your PATA devices as expected?

As a tangent, I wonder if the latest cdrecord works in 2.4 with 'dev=/dev/hdc' ... that would elimiante the need for ide-scsi.

Jeff

#7 lore raw
Quoted 8 lines · Jeff Garzik
Quoted 7 lines · Erik Andersen

When I have the Bios set to compatible mode everything works -- except for the obvious problem that I have to put my SATA drive onto my promise SATA card (since the ICH5 SATA is disabled).

When I have the Bios set to Enhanced mode (so the ICH5 provides both SATA and PATA) then my system will wedge solid as a rock.

Quoted 7 lines
Quoted 4 lines

It turns out it was locking up while loading up the ide-scsi kernel module. I have

options ide-cd ignore='hdc'

So, things work in Enchanced mode if ide-scsi module is not loaded?

After a bit more testing.... loading either ide-scsi or ide-cd is sufficient to lock my system dead dead dead if the bios is set to Enhanced mode.

After _not_ loading ide-scsi or ide-cd I was able to boot in Enhanced mode. I think I am getting some sortof wierd interrupt storm. Everything freezes for a few second every so often... Here is what I am seeing.

$ uptime
 00:51:41 up 25 min,  3 users,  load average: 0.04, 0.10, 0.07
$ cat /proc/interrupts 
           CPU0       CPU1       
  0:     152450          0    IO-APIC-edge  timer
  1:       5334          0    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  8:          4          0    IO-APIC-edge  rtc
  9:          0          0   IO-APIC-level  acpi
 12:      36125          0    IO-APIC-edge  PS/2 Mouse
 16:     105720          0   IO-APIC-level  usb-uhci, usb-uhci, radeon@PCI:1:0:0
 17:          0          0   IO-APIC-level  Intel ICH5
 18:  175250680       2019   IO-APIC-level  ide0, ide1, libata, usb-uhci
 19:          0          0   IO-APIC-level  usb-uhci
 22:      90380          0   IO-APIC-level  SysKonnect SK-98xx, bttv
 23:          0          0   IO-APIC-level  ehci_hcd
NMI:          0          0 
LOC:     156771     156777 
ERR:          0
MIS:       2019

I have a P4 with hyperthreading so my kernel is SMP. The huge number of interrupts on 18 (I'm not doing very much beyong ssh to another box to write this email) looks suspicious to me.

Quoted 1 line

And, drivers/ide is picking up your PATA devices as expected?

yes.

Quoted 2 lines

As a tangent, I wonder if the latest cdrecord works in 2.4 with 'dev=/dev/hdc' ... that would elimiante the need for ide-scsi.

I'll check...

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#8 lore raw
In reply to Jeff Garzik
Quoted 2 lines · Jeff Garzik

As a tangent, I wonder if the latest cdrecord works in 2.4 with 'dev=/dev/hdc' ... that would elimiante the need for ide-scsi.

It probably does, but through the CDROM_SEND_PACKET ioctl which doesn't work very well. It is in no way a suitable replacement for ide-scsi, so I'm afraid this plan wont fly at all.

Signature · 1 line
Jens Axboe
#9 lore raw
In reply to Erik Andersen
Quoted 2 lines · Erik Andersen

It turns out it was locking up while loading up the ide-scsi kernel module. I have

Oooh, ooh, me too!

And I'm not even using libata (I don't think?). I'm just using stock 2.4.23-pre4.

This is a P4P800 with one SATA drive and two PATA drives.

The system works fine as long as ide-scsi isn't loaded (and noflushd doesn't spin down any drives).

Getting ide-scsi working is pretty soon on my todo list as it means being able to play DVDs and use the cdrecorder.

00:00.0 Host bridge: Intel Corp.: Unknown device 2570 (rev 02)

	Subsystem: Asustek Computer, Inc.: Unknown device 80f2
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [e4] #09 [2106]
	Capabilities: [a0] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4

00: 86 80 70 25 06 00 90 20 02 00 00 06 00 00 00 00 10: 08 00 00 f8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f2 80 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 02 08 00 40 80 1c 00 00 00 00 00 00 00 00 00 60: 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 00 00 00 33 33 00 00 00 00 00 00 0a 38 00
a0: 02 00 30 00 17 42 00 1f 04 03 00 00 00 00 00 00
b0: 80 00 00 00 30 00 00 00 00 00 ee 09 20 10 00 00
c0: 00 00 00 00 00 40 0e 28 00 00 00 00 00 00 00 00
d0: 02 28 04 0e 0b 0d 00 00 00 00 00 00 00 00 20 01
e0: 00 00 00 00 09 a0 06 21 00 02 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00

00:01.0 PCI bridge: Intel Corp.: Unknown device 2571 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f2d00000-f3dfffff
Prefetchable memory behind bridge: eec00000-f2bfffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00: 86 80 71 25 07 01 a0 00 02 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 a0 02
20: d0 f2 d0 f3 c0 ee b0 f2 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00

00:1d.0 USB Controller: Intel Corp.: Unknown device 24d2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef00 [size=32]
00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 0f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.1 USB Controller: Intel Corp.: Unknown device 24d4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at ef20 [size=32]
00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 21 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 0f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.2 USB Controller: Intel Corp.: Unknown device 24d7 (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ef40 [size=32]
00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 0f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.3 USB Controller: Intel Corp.: Unknown device 24de (rev 02) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef80 [size=32]
00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 0f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1d.7 USB Controller: Intel Corp.: Unknown device 24dd (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at f7fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00
10: 00 fc ff f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 00 80
70: 00 00 cf 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 55 55 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 80 00 00 88 83 40 00 66 0f 04 00 06 14 00 00

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f3e00000-f7efffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 40 d0 d0 80 02
20: e0 f3 e0 f7 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
40: 02 28 30 76 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 64 73 00 00 00 00 00 50 01 34 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 4f 35

00:1f.0 ISA bridge: Intel Corp.: Unknown device 24d0 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 10 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 81 04 00 00 10 00 00 00
60: 0a 0b 05 05 d0 00 00 00 80 80 0b 0b 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: ff fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 20 02 00 00 01 00 00 00 0d 00 00 00 00 03 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 86 21 00 00 02 0f 00 00 04 00 00 00 00 00 00 00
e0: 00 00 00 80 00 00 08 14 33 22 11 00 00 00 67 45
f0: 00 00 40 00 04 00 00 00 66 0f 04 1e 00 00 00 00

00:1f.1 IDE interface: Intel Corp.: Unknown device 24db (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
00: 86 80 db 24 07 00 88 02 02 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 01 fc 00 00 00 00 00 40 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
40: 77 e3 70 c0 bb 00 00 00 0b 00 12 20 00 00 00 00
50: 00 00 00 00 32 20 00 00 00 00 00 00 00 00 00 00
60: 08 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at efe0 [size=8]
Region 1: I/O ports at efac [size=4]
Region 2: I/O ports at efa0 [size=8]
Region 3: I/O ports at efa8 [size=4]
Region 4: I/O ports at ef60 [size=16]
00: 86 80 d1 24 05 00 a0 02 02 8f 01 01 00 00 00 00
10: e1 ef 00 00 ad ef 00 00 a1 ef 00 00 a9 ef 00 00
20: 61 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
40: 00 80 07 a3 00 00 00 00 04 00 00 03 00 00 00 00
50: 00 00 00 00 c0 40 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 23 00 20 00 00 00 00 00 00 00 00 00 00 00
a0: 40 00 00 00 43 00 22 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.3 SMBus: Intel Corp.: Unknown device 24d3 (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 0400 [size=32]
00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

00:1f.5 Multimedia audio controller: Intel Corp.: Unknown device 24d5 (rev 02)
Subsystem: Asustek Computer, Inc.: Unknown device 80f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at f7fff400 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f7fff000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00
10: 01 e8 00 00 81 ee 00 00 00 f4 ff f7 00 f0 ff f7
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f3 80
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 02 00 00
40: 09 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 c2 c9 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 04) (prog-if 00 [VGA])

	Subsystem: Matrox Graphics, Inc. Millennium G400 16Mb SDRAM
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (4000ns min, 8000ns max), cache line size 04
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M]
	Region 1: Memory at f3dfc000 (32-bit, non-prefetchable) [size=16K]
	Region 2: Memory at f3000000 (32-bit, non-prefetchable) [size=8M]
	Expansion ROM at f3de0000 [disabled] [size=64K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [f0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4

00: 2b 10 25 05 06 00 90 02 04 00 00 03 04 40 00 00 10: 08 00 00 f0 00 c0 df f3 00 00 00 f3 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 38 03 30: 00 00 de f3 dc 00 00 00 00 00 00 00 0a 01 10 20 40: 20 81 53 50 08 3c 00 00 00 00 00 00 00 00 00 00 50: 00 30 00 01 19 84 9b 01 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 f0 22 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 02 00 20 00 07 02 00 1f 04 03 00 1f 00 00 00 00

02:05.0 Ethernet controller: 3Com Corporation: Unknown device 1700 (rev 12)
Subsystem: Asustek Computer, Inc.: Unknown device 80eb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), cache line size 04
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f7eec000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data
00: b7 10 00 17 17 01 b0 02 12 00 00 02 04 40 00 00
10: 00 c0 ee f7 01 d8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 eb 80
30: 00 00 00 00 48 00 00 00 00 00 00 00 0b 01 17 1f
40: 00 00 b0 05 01 40 a0 01 01 50 02 fe 00 2e 00 0c
50: 03 00 fc 80 00 00 00 78 00 00 04 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:0a.0 VGA compatible controller: Texas Instruments TVP4010 [Permedia] (rev 01) (prog-if 00 [VGA])

	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at f7ec0000 (32-bit, non-prefetchable) [disabled] [size=128K]
	Region 1: Memory at f7000000 (32-bit, non-prefetchable) [disabled] [size=8M]
	Region 2: Memory at f6800000 (32-bit, non-prefetchable) [disabled] [size=8M]
	Expansion ROM at f7ef0000 [disabled] [size=64K]

00: 4c 10 04 3d 00 00 80 02 01 00 00 03 00 40 00 00 10: 00 00 ec f7 00 00 00 f7 00 00 80 f6 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 ef f7 00 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:0c.0 VGA compatible controller: ATI Technologies Inc 3D Rage I/II 215GT [Mach64 GT] (rev 41) (prog-if 00 [VGA])

	Subsystem: ATI Technologies Inc 3D Rage I/II 215GT [Mach64 GT]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at d000 [size=256]
	Region 2: Memory at f7eeb000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at f7ea0000 [disabled] [size=128K]

00: 02 10 54 47 83 00 80 02 41 00 00 03 04 40 00 00 10: 00 00 00 f5 01 d0 00 00 00 b0 ee f7 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 54 47 30: 00 00 ea f7 00 00 00 00 00 00 00 00 ff 00 08 00 40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Signature · 1 line
greg
#10 lore raw
Quoted 11 lines · Greg Stark
Quoted 2 lines · Erik Andersen

It turns out it was locking up while loading up the ide-scsi kernel module. I have

Oooh, ooh, me too!

And I'm not even using libata (I don't think?).
I'm just using stock 2.4.23-pre4.

Quoted 7 lines

This is a P4P800 with one SATA drive and two PATA drives.

The system works fine as long as ide-scsi isn't loaded (and noflushd doesn't spin down any drives).

Getting ide-scsi working is pretty soon on my todo list as it means being able to play DVDs and use the cdrecorder.

Do check your /proc/interrupts though. With my P4P800 I found that when set to Enhanced mode, and when ide-scsi was carefully avoided, I was still getting a storm of interrupts that were doing rather bad things for system performance. Can you check if you are also seeing the same thing? i.e. does the interrupt line with your ide controller(s) on it show bazillions of interrupts?

-Erik

--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--

#11 lore raw
Quoted 6 lines · Erik Andersen

Do check your /proc/interrupts though. With my P4P800 I found that when set to Enhanced mode, and when ide-scsi was carefully avoided, I was still getting a storm of interrupts that were doing rather bad things for system performance. Can you check if you are also seeing the same thing? i.e. does the interrupt line with your ide controller(s) on it show bazillions of interrupts?

Well I'm not really sure what numbers would be reasonable here, but these don't seem insane to me.

bash-2.05b$ uptime
21:24:57 up 7 days, 10:41, 10 users, load average: 0.10, 0.07, 0.01

CPU0 CPU1

  0:   64325490          0    IO-APIC-edge  timer
  1:     629096          0    IO-APIC-edge  keyboard
  2:          0          0          XT-PIC  cascade
  8:   40215382          0    IO-APIC-edge  rtc
  9:          0          0   IO-APIC-level  acpi
 12:    5479273          0    IO-APIC-edge  PS/2 Mouse
 14:     382236          1    IO-APIC-edge  ide0
 15:         63          0    IO-APIC-edge  ide1
 17:    5379508          0   IO-APIC-level  Intel ICH5
 18:    4574111          2   IO-APIC-level  ide3
 22:   26963560          0   IO-APIC-level  SysKonnect SK-98xx
NMI:          0          0 
LOC:   64325091   64325140 
ERR:          0
MIS:          2
Signature · 1 line
greg