Skip to contentSkip to conversation

Better performance with pdc20376 compared to SiI 3112

DISCUSSION Eduard Hasenleithner 3 participants 3 messages Nov 28, 2003 – Nov 30, 2003

lore
Share & tools
lore
#0 lore raw

Hello.

Although I like the SiI 3112 due it's open specs I found that the somehow "closed" pdc20376 promise chip performs essentially better with the new GPL drivers on a non-tweaked 2.6.0-test11 kernel :( With SiI 3112 I get about 16MB/s, with pdc20376 54MB/s, which is most likely the maximum harddisk performance of my seagate drive.

So what is the status of the siimage driver? Can I expect it to improve in further kernel releases?

On a further note I found that no /proc/ide nodes are allocated for the siimage driver. What can be the reason for this?

Below this section I show output from dd and hdparm in order to give information about my setup.

=== test with promise pdc20376 ===
boundary:~ # time dd if=/dev/sda of=/dev/null bs=1048576 count=1024 1024+0 records in
1024+0 records out

real    0m18.441s
user    0m0.004s
sys     0m3.428s

=== reboot, test with SiI 3112 ====
boundary:~ # time dd if=/dev/hde of=/dev/null bs=1048576 count=1024 1024+0 records in
1024+0 records out

real    1m2.666s
user    0m0.003s
sys     0m4.009s

=== second try, just to be sure ===
boundary:~ # time dd if=/dev/hde of=/dev/null bs=1048576 count=1024 1024+0 records in
1024+0 records out

real    1m2.648s
user    0m0.006s
sys     0m3.884s

=== output of hdparm ===
boundary:~ # hdparm -I /dev/hde
/dev/hde:

ATA device, with non-removable media

	Model Number:       ST3120026AS
	Serial Number:      3JS1X69W
	Firmware Revision:  3.56
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2
	Supported: 6 5 4 3
Configuration:
	Logical		max	current
	cylinders	16383	65535
	heads		16	1
	sectors/track	63	63
	--
	CHS current addressable sectors:    4128705
	LBA    user addressable sectors:  234441648
	LBA48  user addressable sectors:  234441648
	device size with M = 1024*1024:      114473 MBytes
	device size with M = 1000*1000:      120034 MBytes (120 GB)

Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard
R/W multiple sector transfer: Max = 16 Current = ?
Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct

=== ls -R /proc/ide (where is hde?) ===
/proc/ide:
. .. drivers hda hdc ide0 ide1 via

/proc/ide/ide0:
. .. channel config hda mate model

/proc/ide/ide0/hda:

.   cache     driver    identify  model     smart_thresholds
..  capacity  geometry  media     settings  smart_values

/proc/ide/ide1:
. .. channel config hdc mate model

/proc/ide/ide1/hdc:
. .. capacity driver identify media model settings

=== lspci -v (snipped) ===
00:07.0 RAID bus controller: CMD Technology Inc Silicon Image SiI 3112 SATARaid Controller (rev 02)

	Subsystem: CMD Technology Inc: Unknown device 6112
	Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 19
	I/O ports at ec00 [size=8]
	I/O ports at e800 [size=4]
	I/O ports at e400 [size=8]
	I/O ports at e000 [size=4]
	I/O ports at dc00 [size=16]
	Memory at dffffe00 (32-bit, non-prefetchable) [size=512]
	Expansion ROM at dff00000 [disabled] [size=512K]
	Capabilities: [60] Power Management version 2

00:0d.0 RAID bus controller: Promise Technology, Inc. PDC20376 (rev 02)

	Subsystem: Promise Technology, Inc.: Unknown device 6620
	Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 19
	I/O ports at bc00 [size=64]
	I/O ports at b800 [size=16]
	I/O ports at b400 [size=128]
	Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
	Memory at dffc0000 (32-bit, non-prefetchable) [size=128K]
	Capabilities: [60] Power Management version 2

Thanks for any hints!

#1 lore raw
Quoted 3 lines · Eduard Hasenleithner

Hello.

Although I like the SiI 3112 due it's open specs I found that the

There are no open specs for SiI3112, "datasheet" from SiI page is useless.

--bart

Quoted 13 lines

somehow "closed" pdc20376 promise chip performs essentially better with the new GPL drivers on a non-tweaked 2.6.0-test11 kernel :( With SiI 3112 I get about 16MB/s, with pdc20376 54MB/s, which is most likely the maximum harddisk performance of my seagate drive.

So what is the status of the siimage driver? Can I expect it to improve in further kernel releases?

On a further note I found that no /proc/ide nodes are allocated for the siimage driver. What can be the reason for this?

Below this section I show output from dd and hdparm in order to give information about my setup.

<...>

#2 lore raw
In reply to Eduard Hasenleithner
Quoted 7 lines · Eduard Hasenleithner

Hello.

Although I like the SiI 3112 due it's open specs I found that the somehow "closed" pdc20376 promise chip performs essentially better with the new GPL drivers on a non-tweaked 2.6.0-test11 kernel :( With SiI 3112 I get about 16MB/s, with pdc20376 54MB/s, which is most likely the maximum harddisk performance of my seagate drive.

Like Bart mentioned, both Promise and SiI are the same: closed specs, GPL'd driver.

Quoted 2 lines

So what is the status of the siimage driver? Can I expect it to improve in further kernel releases?

I certainly hope so :) We're actively discussing the 3112 errata fix right now...

Jeff