Skip to contentSkip to conversation

Silicon Image 3112A SATA trouble

DISCUSSION Luis Miguel García 2 participants 2 messages Nov 30, 2003

lore
Share & tools
lore
#0 lore raw

so definitely, 32 MB/s is almost half the speed that you get. I'm in 2.6-test11. I don't know more options to try. The next will be booting with "noapic nolapic". Some people reported better results with this.

by the way, I have booted with "doataraid noraid" (no drives connected, only SATA support in bios), and nothing is shown in the boot messages (nor dmesg) about libata being loaded. I don't know if I must connect a hard drive and then the driver shows up, but I don't think that.

Thanks!

LuisMi Garcia

Quoted 35 lines · Craig Bradney

On the topic of speeds.. hdparm -t gives me 56Mb/s on my Maxtor 80Mb 8mb cache PATA drive. I got that with 2.4.23 pre 8 which was ATA100 and get just a little more on ATA133 with 2.6. Not sure what people are expecting on SATA.

Craig

Quoted 20 lines · Luis Miguel García

hello:

I have a Seagate Barracuda IV (80 Gb) connected to parallel ata on a nforce-2 motherboard.

If any of you want for me to test any patch to fix the "seagate issue", please, count on me. I have a SATA sis3112 and a parallel-to-serial converter. If I'm of any help to you, drop me an email.

By the way, I'm only getting 32 MB/s (hdparm -tT /dev/hda) on my actual parallel ata. Is this enough for an ATA-100 device?

Thanks a lot.

LuisMi García
Spain

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#1 lore raw
Quoted 8 lines · Luis Miguel García

so definitely, 32 MB/s is almost half the speed that you get. I'm in 2.6-test11. I don't know more options to try. The next will be booting with "noapic nolapic". Some people reported better results with this.

by the way, I have booted with "doataraid noraid" (no drives connected, only SATA support in bios), and nothing is shown in the boot messages (nor dmesg) about libata being loaded. I don't know if I must connect a hard drive and then the driver shows up, but I don't think that.

Depends on a lot of things, especially what else is on that controller. The way I found things was my involvement in the Scribus DTP project. I upgraded to the Athlon 2600 from a Duron 900.

That took me from 30+mins from a Scribus compile to 2 mins (!) if there is no secondary drive. When I had my old 20gb drive plugged in to do copies off of it.. 11mins. Do you have anything else plugged in there? Of course, I guess in that case the 8mb drive cache is helping a lot.

Craig

Quoted 58 lines

Thanks!

LuisMi Garcia

Quoted 5 lines · Craig Bradney

On the topic of speeds.. hdparm -t gives me 56Mb/s on my Maxtor 80Mb 8mb cache PATA drive. I got that with 2.4.23 pre 8 which was ATA100 and get just a little more on ATA133 with 2.6. Not sure what people are expecting on SATA.

Quoted 36 lines

Craig

Quoted 26 lines · Luis Miguel García

hello:

I have a Seagate Barracuda IV (80 Gb) connected to parallel ata on a nforce-2 motherboard.

If any of you want for me to test any patch to fix the "seagate issue", please, count on me. I have a SATA sis3112 and a parallel-to-serial converter. If I'm of any help to you, drop me an email.

By the way, I'm only getting 32 MB/s (hdparm -tT /dev/hda) on my
actual parallel ata. Is this enough for an ATA-100 device?

Thanks a lot.

LuisMi García
Spain

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/