Skip to contentSkip to conversation

NForce2 pseudoscience stability testing (2.6.0-test11)

DISCUSSION [email protected] 10 participants 16 messages Dec 4, 2003 – Dec 5, 2003

lore
Share & tools
lore
#0 lore raw

Dan Creswell wrote:

Thanks for the input, I'll pass it to the list.

Most of these Athlon victims are UP users, in fact, I believe they are exclusively UP. Does MPS 1.1/1.4 play a role in a UP system ever? I dont think the NForce2 chipset, where we are seeing these hard hangs (no ping, no screen, no blinking cursor, no toggling the caps lock, nothing) is capable of SMP operation.

Now whats interesting is you finger the IDE as a potential culprit and think its very low level. Interesting.

By the way, I've had trouble with SMP on a Tyan board with an i840 chipset with Linux before - I was never able to resolve the issue and had to return the board.

I've beaten on an Intel SR1300 and SR2300 dual Xeon (aka Micron's Netframe 1610/2610 aka Sun 60x / 65x) and never run into these hangs with kernels up to 2.4.22. The motherboard is an Intel SE7501WV2 .

Quoted 15 lines

Hi,
Been following this thread silently for a while and thought I'd drop you
a line as I have some other data you may find useful.

My machine is a dual Xeon with 2Gb, E1000 NIC, MPT LSI SCSI disks and an
IDE CDROM.

2.6-test9 is only stable on this machine with noapic passed in the kernel parameters - otherwise, it lock's up in no time flat. I can also
run this kernel in single-processor mode with the APIC enabled and that's stable.

Quoted 4 lines

2.4.23-rc2 runs fine on the same machine with the APIC enabled in SMP mode.

2.4.23-rc5 locks up on this machine if I use the same .config as

for

Quoted 1 line

-rc2. However, if I disable ACPI and pass "pci=noacpi" to the

kernel,

Quoted 2 lines

this too runs fine.
- Seems like the ACPI changes in -rc3 are a problem for my

machine.

Quoted 2 lines

All of these behaviors have been observed with MPS 1.4 (I've

changed

Quoted 1 line

that BIOS setting to 1.1 today in preparation for more testing of

the

Quoted 3 lines

above to see if that makes a difference).

I mention all of this because none of my lock-ups have happened

whilst

Quoted 1 line

accessing the IDE subsystem. I *have* had lockups with

simultaneous

Quoted 2 lines

network and disk access and I've also seen it with simply mouse-waggling. I suspect that the problem is *very* low-level

and

Quoted 1 line

likely related to the interrupt load. In my case, the problems

only

Quoted 1 line

seem to occur with SMP configurations which makes me suspect there

may

Quoted 9 lines

be a locking/simultaneous update problem.

Oh, forgot to say, my motherboard is a Tyan Thunder S2665 (based on the
intel E7505 chipset).

Hope that helps,

Dan.

#1 lore raw

As reported earlier today I had the first lockup this morning in over 5 days uptime. Having had that, I decided to go for the latest gentoo 2.6 test 11-r1 kernel. This means I was now running the following patches:
http://dev.gentoo.org/~brad_mssw/kernel_patches/2.6.0/genpatches-0.7/
instead of
http://dev.gentoo.org/~brad_mssw/kernel_patches/2.6.0/genpatches-0.6/
on top of vanilla test 11.

Anyway.. my two changes on rebuilding the kernel were initially:
-Add in preempt (because there were questions asked here) -Remove generic IDE support (I know I have Nvidia IDE so lets only have that one).

In that configuration the "multiple hdparm -t /dev/hda" test hung my system.

Rebuilt kernel without preempt.. no hang on hdparm test.

So in summary, apart from the patch changes as above, the only difference is to my 5 day kernel I now dont have generic IDE support included.

So now, I'll leave it on and see how far it goes.. 13 mins so far :).

regards
Craig

Quoted 83 lines · On Thu, 2003-12-04 at 13:17, [email protected] wrote:

Dan Creswell wrote:

Thanks for the input, I'll pass it to the list.

Most of these Athlon victims are UP users, in fact, I believe they are exclusively UP. Does MPS 1.1/1.4 play a role in a UP system ever? I dont think the NForce2 chipset, where we are seeing these hard hangs (no ping, no screen, no blinking cursor, no toggling the caps lock, nothing) is capable of SMP operation.

Now whats interesting is you finger the IDE as a potential culprit and think its very low level. Interesting.

By the way, I've had trouble with SMP on a Tyan board with an i840 chipset with Linux before - I was never able to resolve the issue and had to return the board.

I've beaten on an Intel SR1300 and SR2300 dual Xeon (aka Micron's Netframe 1610/2610 aka Sun 60x / 65x) and never run into these hangs with kernels up to 2.4.22. The motherboard is an Intel SE7501WV2 .

Quoted 15 lines

Hi,
Been following this thread silently for a while and thought I'd drop you
a line as I have some other data you may find useful.

My machine is a dual Xeon with 2Gb, E1000 NIC, MPT LSI SCSI disks and an
IDE CDROM.

2.6-test9 is only stable on this machine with noapic passed in the kernel parameters - otherwise, it lock's up in no time flat. I can also
run this kernel in single-processor mode with the APIC enabled and that's stable.

Quoted 4 lines

2.4.23-rc2 runs fine on the same machine with the APIC enabled in SMP mode.

2.4.23-rc5 locks up on this machine if I use the same .config as

for

Quoted 1 line

-rc2. However, if I disable ACPI and pass "pci=noacpi" to the

kernel,

Quoted 2 lines

this too runs fine.
- Seems like the ACPI changes in -rc3 are a problem for my

machine.

Quoted 2 lines

All of these behaviors have been observed with MPS 1.4 (I've

changed

Quoted 1 line

that BIOS setting to 1.1 today in preparation for more testing of

the

Quoted 3 lines

above to see if that makes a difference).

I mention all of this because none of my lock-ups have happened

whilst

Quoted 1 line

accessing the IDE subsystem. I *have* had lockups with

simultaneous

Quoted 2 lines

network and disk access and I've also seen it with simply mouse-waggling. I suspect that the problem is *very* low-level

and

Quoted 1 line

likely related to the interrupt load. In my case, the problems

only

Quoted 1 line

seem to occur with SMP configurations which makes me suspect there

may

Quoted 9 lines

be a locking/simultaneous update problem.

Oh, forgot to say, my motherboard is a Tyan Thunder S2665 (based on the
intel E7505 chipset).

Hope that helps,

Dan.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
Quoted 18 lines · Craig Bradney

As reported earlier today I had the first lockup this morning in over 5 days uptime. Having had that, I decided to go for the latest gentoo 2.6 test 11-r1 kernel. This means I was now running the following patches:
http://dev.gentoo.org/~brad_mssw/kernel_patches/2.6.0/genpatches-0.7/
instead of
http://dev.gentoo.org/~brad_mssw/kernel_patches/2.6.0/genpatches-0.6/
on top of vanilla test 11.

Anyway.. my two changes on rebuilding the kernel were initially:

(quoted diff) +0 -2
-Add in preempt (because there were questions asked here) 
-Remove generic IDE support (I know I have Nvidia IDE so lets only have

that one).

In that configuration the "multiple hdparm -t /dev/hda" test hung my system.

Rebuilt kernel without preempt.. no hang on hdparm test.

Quoted 10 lines

So in summary, apart from the patch changes as above, the only difference is to my 5 day kernel I now dont have generic IDE support included.

So now, I'll leave it on and see how far it goes.. 13 mins so far :).

regards
Craig

Just to add more inconsistency into the mix, I am running with preempt enabled, generic ide disabled, and can't make it crash. Ran netperf for an hour over a crossover cable on 100mbit, a couple make -j 30 kernel compiles, dbench, and playing some mp3's all at the same time and nothing happens despite load average reaching over 100. Maybe I am just lucky.

Signature · 6 lines
Josh McKinney		     |	Webmaster: http://joshandangie.org
--------------------------------------------------------------------------
                             | They that can give up essential liberty
Linux, the choice       -o)  | to obtain a little temporary safety deserve 
of the GNU generation    /\  | neither liberty or safety. 
                        _\_v |                          -Benjamin Franklin
#3 lore raw

Josh McKinney <[email protected]> writes:

Hello Josh,

Quoted 6 lines

Just to add more inconsistency into the mix, I am running with preempt enabled, generic ide disabled, and can't make it crash. Ran netperf for an hour over a crossover cable on 100mbit, a couple make -j 30 kernel compiles, dbench, and playing some mp3's all at the same time and nothing happens despite load average reaching over 100. Maybe I am just lucky.

Or maybe not.

In the very beginning, 1 or 2 months ago right after I bought the board, it did crash but it actually didn't crash very often. In fact, most of the time (not every time, but most!) it crashed while the system being rather idle. To add even more perplexity to it: I could work on the system for hours and then leave the computer half an hour alone for talking a walk or jogging or whatever and, after coming back, run across a complete lockup. Normally, the clock applet on my desktop told me that the box crashed several minutes after I went out, since the clock of course froze with the mainboard as well.

A lot changed by now, hardware and software, and now I'm hardly able to run the system with ACPI/APIC enabled at all. If the boot procedure goes fine, it locks up shortly after. If fsck decides to check the disks, the mainboard is doomed to lock up away immediately.

That really is a nasty problem.

Regards,
Julien

#4 lore raw
Quoted 23 lines · Julien Oster

Josh McKinney <[email protected]> writes:

Hello Josh,

Quoted 6 lines

Just to add more inconsistency into the mix, I am running with preempt enabled, generic ide disabled, and can't make it crash. Ran netperf for an hour over a crossover cable on 100mbit, a couple make -j 30 kernel compiles, dbench, and playing some mp3's all at the same time and nothing happens despite load average reaching over 100. Maybe I am just lucky.

Or maybe not.

In the very beginning, 1 or 2 months ago right after I bought the board, it did crash but it actually didn't crash very often. In fact, most of the time (not every time, but most!) it crashed while the system being rather idle. To add even more perplexity to it: I could work on the system for hours and then leave the computer half an hour alone for talking a walk or jogging or whatever and, after coming back, run across a complete lockup. Normally, the clock applet on my desktop told me that the box crashed several minutes after I went out, since the clock of course froze with the mainboard as well.

Quoted 7 lines

A lot changed by now, hardware and software, and now I'm hardly able to run the system with ACPI/APIC enabled at all. If the boot procedure goes fine, it locks up shortly after. If fsck decides to check the disks, the mainboard is doomed to lock up away immediately.

That really is a nasty problem.

This issue seems to be funny like that. When I first recieved this mobo I too had crashes like you say you are having now. Doing practically anything would make it crash, passing noapic and nolapic on boot solved the problems. Now, as I said, stable with all ACPI APIC LAPIC enabled. I haven't changed any hardware or anything either, except for now I am using the nvidia ethernet with the forcedeth driver, but I somehow don't think that has anything to do with it, maybe it is worth looking into.

Signature · 6 lines
Josh McKinney		     |	Webmaster: http://joshandangie.org
--------------------------------------------------------------------------
                             | They that can give up essential liberty
Linux, the choice       -o)  | to obtain a little temporary safety deserve 
of the GNU generation    /\  | neither liberty or safety. 
                        _\_v |                          -Benjamin Franklin
#5 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7. Several people posted their /proc/interrupts but it only shows interrupts a driver registered and is using. I noticed a non-constant stream of interrupts on IRQ7 using sar and I am also able to see it under /proc/interrupts when loading parport_pc with options to get the driver using the interrupt. However it is not related to the parallel port because putting it on IRQ5 or disabling it in the BIOS does not affect the stream of interrupts on IRQ7. I wonder if people experiencing lockup problems also have these noise interrupts, and I don't know if this has something to do with the lockups or if it is an independant problem.

Of course, booting with noapic nolapic, the system is rock-solid, and the interrupt counter on IRQ7 stays solidly at 1 (should it be 0 ?), until I use something on the parallel port of course.

Motherboard : abit nfs7-s v2.0, nforce2 chipset
Kernels : 2.6.0-test9, 2.6.0-test10, 2.6.0-test10-mm1, 2.6.0-test11

/proc/interrupts with apic+lapic, shortly after boot, already 408 interrupts on IRQ7 :
CPU0

  0:     121148          XT-PIC  timer
  1:        279    IO-APIC-edge  i8042
  2:          0          XT-PIC  cascade
  7:        408    IO-APIC-edge  parport0
  8:          4    IO-APIC-edge  rtc
  9:          0   IO-APIC-level  acpi
 14:       2591    IO-APIC-edge  ide0
 15:       2916    IO-APIC-edge  ide1
 16:         47   IO-APIC-level  eth0
 18:          0   IO-APIC-level  EMU10K1
 19:       4373   IO-APIC-level  mga@PCI:2:0:0
 20:         31   IO-APIC-level  ohci-hcd
 21:          0   IO-APIC-level  ehci_hcd, NVidia nForce2
 22:          0   IO-APIC-level  ohci-hcd
NMI:          0
LOC:     120982
ERR:          0
MIS:          0

/proc/interrupts with noapic and nolapic, with IRQ7 showing only 1 interrupt since boot :
CPU0

  0:     803521          XT-PIC  timer
  1:       1446          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  5:      54875          XT-PIC  mga@PCI:2:0:0
  7:          1          XT-PIC  parport0
  8:          4          XT-PIC  rtc
  9:          0          XT-PIC  acpi
 10:      16027          XT-PIC  ohci_hcd,eth0, NVidia nForce2
 11:    1903732          XT-PIC  bttv0, ehci_hcd, EMU10K1
 12:       9416          XT-PIC  ohci_hcd
 14:       8513          XT-PIC  ide0
 15:       3910          XT-PIC  ide1
NMI:          0
LOC:          0
ERR:          0
MIS:          0

Mathieu

#6 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

Quoted 5 lines · [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

Have you seen "IRQ7 Disabled" errors?

On my nforce2 mboard(MSI K7N2 MCP2-T) I would
see that err if onboard ethernet was enabled. I haven't gotten eth to work and I have to disable onboard ethernet. I had to disable usb for a while, now it just doesn't work but doesn't cause a problem so I disable it anyway. I am using a tulip card instead of onboard ethernet. I disable the parallel port.

This is /proc/interrupts with apic, lapic, onboard eth disabled, parallel disabled, bios flash, stable with
kernel 2.6.0-test* test11 no irq 7!

cat /proc/interrupts
CPU0

 0:   47830174          XT-PIC  timer
 1:      24026    IO-APIC-edge  i8042
 2:          0          XT-PIC  cascade
 4:        228    IO-APIC-edge  serial
 8:          1    IO-APIC-edge  rtc
 9:          0   IO-APIC-level  acpi
12:     125368    IO-APIC-edge  i8042
14:         22    IO-APIC-edge  ide0
15:         24    IO-APIC-edge  ide1
16:     592751   IO-APIC-level  3ware Storage Controller, yenta, yenta
17:    1309695   IO-APIC-level  eth0
21:          0   IO-APIC-level  NVidia nForce2
NMI:          0
LOC:   47829780
ERR:          0
MIS:          4

-Bob

Quoted 71 lines

Several people posted their
/proc/interrupts but it only shows interrupts a driver registered and is using. I noticed a non-constant stream of interrupts on IRQ7 using sar and I am also able to see it under /proc/interrupts when loading parport_pc with options to get the driver using the interrupt. However it is not related to the parallel port because putting it on IRQ5 or disabling it in the BIOS does not affect the stream of interrupts on IRQ7. I wonder if people experiencing lockup problems also have these noise interrupts, and I don't know if this has something to do with the lockups or if it is an independant problem.

Of course, booting with noapic nolapic, the system is rock-solid, and the interrupt counter on IRQ7 stays solidly at 1 (should it be 0 ?), until I use something on the parallel port of course.

Motherboard : abit nfs7-s v2.0, nforce2 chipset
Kernels : 2.6.0-test9, 2.6.0-test10, 2.6.0-test10-mm1, 2.6.0-test11

/proc/interrupts with apic+lapic, shortly after boot, already 408 interrupts on IRQ7 :
CPU0

 0:     121148          XT-PIC  timer
 1:        279    IO-APIC-edge  i8042
 2:          0          XT-PIC  cascade
 7:        408    IO-APIC-edge  parport0
 8:          4    IO-APIC-edge  rtc
 9:          0   IO-APIC-level  acpi
14:       2591    IO-APIC-edge  ide0
15:       2916    IO-APIC-edge  ide1
16:         47   IO-APIC-level  eth0
18:          0   IO-APIC-level  EMU10K1
19:       4373   IO-APIC-level  mga@PCI:2:0:0
20:         31   IO-APIC-level  ohci-hcd
21:          0   IO-APIC-level  ehci_hcd, NVidia nForce2
22:          0   IO-APIC-level  ohci-hcd
NMI:          0
LOC:     120982
ERR:          0
MIS:          0

/proc/interrupts with noapic and nolapic, with IRQ7 showing only 1 interrupt since boot :
CPU0

 0:     803521          XT-PIC  timer
 1:       1446          XT-PIC  i8042
 2:          0          XT-PIC  cascade
 5:      54875          XT-PIC  mga@PCI:2:0:0
 7:          1          XT-PIC  parport0
 8:          4          XT-PIC  rtc
 9:          0          XT-PIC  acpi
10:      16027          XT-PIC  ohci_hcd,eth0, NVidia nForce2
11:    1903732          XT-PIC  bttv0, ehci_hcd, EMU10K1
12:       9416          XT-PIC  ohci_hcd
14:       8513          XT-PIC  ide0
15:       3910          XT-PIC  ide1
NMI:          0
LOC:          0
ERR:          0
MIS:          0

Mathieu
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#7 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

In reply to [email protected]
Quoted 4 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 2 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

Then I took a look again about 5 seconds later:
7: 41560 IO-APIC-edge parport0

And I looked again, and it was higher. If you take a look repeatally, you see it increases for 2-3 seconds, then stops for 2-3, then starts increasing again and continues like this. This is pretty much an idle system other than me cat'ing. I'm not using the parallel port at all.

Then I looked at the irq with parport_pc setup and with a kernel with APIC all disabled:
7: 0 XT-PIC parport0

And it is the same on repeated cat's.

These kernels are exactly the same except ones compiled with UP APIC and the other isn't. I don't know how parport works, but seeing two different events under this condition does seem suspicious.

Quoted 3 lines

and I don't know if this has something to do with the lockups or if it is an independant problem.

I have no idea, but it is suspicious, as I get lockups and this noise with the APIC enabled kernel.

Jesse

#8 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

Quoted 9 lines · Jesse Allen
Quoted 4 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 8 lines
Quoted 2 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

I just did an experminent with a very light kernel, nearly nothing compiled inside, except apic acpi, preempt and needed stuff plus scsi+libata and no ide. IRQ 7 was not present and every device had its own irq. Nevertheless system locked up at second hdparm run...

Prakash

#9 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

Prakash,

try it without preempt.. just to see. As soon as I removed it today the crashes went away (for 5 hours).. PC is now up for 2.5 hours and I'm waiting to see if it will be 5 hrs or 5 days this time around :)

Craig

Quoted 32 lines · Prakash K. Cheemplavam
Quoted 9 lines · Jesse Allen
Quoted 4 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 8 lines
Quoted 2 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

I just did an experminent with a very light kernel, nearly nothing compiled inside, except apic acpi, preempt and needed stuff plus scsi+libata and no ide. IRQ 7 was not present and every device had its own irq. Nevertheless system locked up at second hdparm run...

Prakash

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#10 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

Quoted 5 lines · Craig Bradney

Prakash,

try it without preempt.. just to see. As soon as I removed it today the crashes went away (for 5 hours).. PC is now up for 2.5 hours and I'm waiting to see if it will be 5 hrs or 5 days this time around :)

Oh Ok, I did a mistake: Checking my kernel config again I noticed my last experiment indeed was with preemp OFF, so it didn't help.

Prakash

Quoted 27 lines · Prakash K. Cheemplavam
Quoted 26 lines
Quoted 11 lines · Jesse Allen
Quoted 4 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 8 lines
Quoted 2 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

I just did an experminent with a very light kernel, nearly nothing compiled inside, except apic acpi, preempt and needed stuff plus scsi+libata and no ide. IRQ 7 was not present and every device had its own irq. Nevertheless system locked up at second hdparm run...

Prakash

#11 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

In reply to Craig Bradney

Do you have onboard ethernet enabled with nforce2 mboard? I am fine with pre-emptive kernel but have to disable onboard ethernet in cmos setup or I see "Disabling IRQ7" and problems develop.

-Bob

Quoted 59 lines · Craig Bradney

Prakash,

try it without preempt.. just to see. As soon as I removed it today the crashes went away (for 5 hours).. PC is now up for 2.5 hours and I'm waiting to see if it will be 5 hrs or 5 days this time around :)

Craig

Quoted 29 lines · Prakash K. Cheemplavam
Quoted 14 lines · Jesse Allen
Quoted 6 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 10 lines
Quoted 4 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

I just did an experminent with a very light kernel, nearly nothing compiled inside, except apic acpi, preempt and needed stuff plus scsi+libata and no ide. IRQ 7 was not present and every device had its own irq. Nevertheless system locked up at second hdparm run...

Quoted 10 lines

Prakash

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#12 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

nforce net is off. 3com is on. (in bios)

Craig

Quoted 79 lines · Bob

Do you have onboard ethernet enabled with nforce2 mboard? I am fine with pre-emptive kernel but have to disable onboard ethernet in cmos setup or I see "Disabling IRQ7" and problems develop.

-Bob

Quoted 54 lines · Craig Bradney

Prakash,

try it without preempt.. just to see. As soon as I removed it today the crashes went away (for 5 hours).. PC is now up for 2.5 hours and I'm waiting to see if it will be 5 hrs or 5 days this time around :)

Craig

Quoted 32 lines · Prakash K. Cheemplavam
Quoted 14 lines · Jesse Allen
Quoted 6 lines · On Thu, Dec 04, 2003 at 09:02:08PM +0100, [email protected] wrote:

Hello,

Along with the lockups already described here, I've noticed an unidentified source of interrupts on IRQ7.

...

Quoted 10 lines
Quoted 4 lines

I wonder if people experiencing lockup problems also have these noise interrupts,

I just took a look at this, by setting up parport_pc, and yes I get noise.

This was my first sample with a kernel with APIC:
7: 29230 IO-APIC-edge parport0

I just did an experminent with a very light kernel, nearly nothing compiled inside, except apic acpi, preempt and needed stuff plus scsi+libata and no ide. IRQ 7 was not present and every device had its own irq. Nevertheless system locked up at second hdparm run...

Quoted 10 lines

Prakash

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Quoted 8 lines

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#14 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

In reply to [email protected]

I've just seen something strange about IRQ7, during one test, the interrupt counter on IRQ7 was in sync with the timer counter, and the difference was about 21400. I rebooted to see what happens at 21.4 seconds after boot and it is more or less the time some modules get loaded by auto-detecting hardware. But unfortunately I now cannot reproduced it, I only get bursts of IRQ7 as initially reported.

I also noted in dmesg of 2.6.0-test that part about timer interrupt :

..TIMER: vector=0x31 pin1=2 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... failed. ...trying to set up timer as Virtual Wire IRQ... failed. ...trying to set up timer as ExtINT IRQ... works.

This is interesting because 2.4.22 and 2.4.23-pre9 shows :

..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found pin 0) ...works.

and then the timer is not in XT-PIC mode but IO-APIC-edge mode, and I also noticed there is no flood of IRQ7 with these 2.4 kernels. Is it Related or not with the IRQ flood or the lockups I don't know.

By the way 2.4.23 shows the same thing as 2.6.0-test, timer in XT-PIC mode and some IRQ7, but way less than 2.6.0-test.

Mathieu

#13 lore raw

Re: NForce2 pseudoscience stability testing (2.6.0-test11) - IRQ flood related ?

In reply to Bob
Quoted 4 lines · Bob

Do you have onboard ethernet enabled with nforce2 mboard? I am fine with pre-emptive kernel but have to disable onboard ethernet in cmos setup or I see "Disabling IRQ7" and problems develop.

No, It is enabled in bios, but in my test run i just didn't compile the forcedeth driver. So the irq 7 didn't showed up. Eben with my "normal" kernel the th0 interface it mapped to irq 10:

CPU0

  0:    1634197          XT-PIC  timer
  1:       2653          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  5:       1620          XT-PIC  Skystar2, ohci_hcd, NVidia nForce2
  8:          3          XT-PIC  rtc
  9:          0          XT-PIC  acpi
 10:       9412          XT-PIC  eth0
 11:     171083          XT-PIC  libata, ohci_hcd, nvidia
 12:     110080          XT-PIC  i8042
 14:         10          XT-PIC  ide0
 15:         15          XT-PIC  ide1
NMI:          0
ERR:          2
#15 lore raw
In reply to [email protected]

I'm going to add my AMD/Nvidia IDE experiences as well as my current nforce2 experience.

Firstly, aside from the forcedeth module vs. nvnet hacked, I have never even known of problems with nforce2 systems. I have a shuttle mn31/n (micro ATX) and I can use firewire, ide hd running udma5, ide cd running udma2, and the only thing I can do to crash/hang the system is to force unload a module. It's running apic, lapic, acpi quite happily, no preempt, run every test since around 2.5.75.

noteing that. I have to run my FSB underclocked by 1 mhz.

my cpu claims to be an xp2400(133/266fsb) but I run it at 132/264. It was hanging/rebooting due to heat.

my other system (a little off topic here) is a dual athlon athlon-mp tyan thunder k7 system. will NOT run with apic and the amd ide driver.

pat erley