VT82C686 - no sound
alsaconf is reporting it cannot be configured.... when the below modules are manually loaded, esd finds the /dev/dsp and runs but there is no sound. Sound worked fine on 2.4.23
Any help would be appreciated. thank you
00:04.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 21)
Running debian sarge with kernel 2.6 test11
== /etc/modules ==snd_via82xxsnd_ac97_codecsnd_pcm_osssnd_page_allocsnd_pcmsnd_timersnd_mixer_osssnd_pcm_osssnd_mpu401_uart
Quoted 11 lines
alsaconf is reporting it cannot be configured.... when the below modules are manually loaded, esd finds the
/dev/dspand runs but there is no sound. Sound worked fine on 2.4.23Any help would be appreciated. thank you
00:04.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 21)
Running debian sarge with kernel 2.6 test11
Quoted 10 lines
==
/etc/modules==snd_via82xxsnd_ac97_codecsnd_pcm_osssnd_page_allocsnd_pcmsnd_timersnd_mixer_osssnd_pcm_osssnd_mpu401_uart
This is not ALSA modules. If you have configured system for use with
ALSA, you don't have to use OSS modules. Use ALSA with OSS emulaton instead. It should works.
Signature · 5 lines
------------------------------------------------------- David "Dave" Jez Brno, CZ, Europe E-mail: [email protected] PGP key: finger [email protected] ---------=[ ~EOF ]=------------------------------------
Quoted 11 lines · David Jez
Quoted 10 lines
==
/etc/modules==snd_via82xxsnd_ac97_codecsnd_pcm_osssnd_page_allocsnd_pcmsnd_timersnd_mixer_osssnd_pcm_osssnd_mpu401_uart
Quoted 3 lines
This is not ALSA modules. If you have configured system for use with
ALSA, you don't have to use OSS modules. Use ALSA with OSS emulaton instead. It should works.
But this _is_ ALSA with the OSS emulation modules loaded (snd_mixer_oss and snd_pcm_oss). :)
The OSS driver module is called via82cxxx_audio afaik.
Bye,
Oliver
Signature · 1 line
Oliver Feiler <kiza@(kcore.de|lionking.org|gmx[pro].net)>
Hmmm I think you are saying I have all the right things loaded? So why does esd run but not make startup beeps and gnome makes no sounds and alsa play makes no sounds?
using kernel 2.6test11
Quoted 25 lines · Oliver Feiler
Quoted 11 lines · David Jez
Quoted 10 lines
==
/etc/modules==snd_via82xxsnd_ac97_codecsnd_pcm_osssnd_page_allocsnd_pcmsnd_timersnd_mixer_osssnd_pcm_osssnd_mpu401_uartQuoted 3 lines
This is not ALSA modules. If you have configured system for use with
ALSA, you don't have to use OSS modules. Use ALSA with OSS emulaton instead. It should works.But this _is_ ALSA with the OSS emulation modules loaded (
snd_mixer_ossandsnd_pcm_oss). :) The OSS driver module is calledvia82cxxx_audioafaik.Bye,
Oliver
|--==> "h" == hanasaki <[email protected]> writes:
h> Hmmm I think you are saying I have all the right things loaded? h> So why does esd run but not make startup beeps and gnome makes no h> sounds and alsa play makes no sounds?
Load your sound modules, then run `alsamixer' and check the volume levels. If they are sitting on zero (which is what I suspect) boost them up to what you want and quit out of the mixer.
Then run alsactl store'. That will store your mixer setting to /etc/asound.state'. Next, check `/etc/modprobe.conf' for a line similar to...
install snd /sbin/modprobe --ignore-install snd && /usr/sbin/alsactl restore
...which will ensure that your mixer settings are restored whenever your sound modules are loaded.
Some sound cards, when they initialise, have all their levels set to zero. You have to reset them every time the card initialises (whenever the modules are loaded), which is what `alsactl' does.
HTH
Signature · 4 lines
|---<Steve Youngs>---------------<GnuPG KeyID: A94B3003>---| | Ashes to ashes, dust to dust. | | The proof of the pudding, is under the crust. | |------------------------------<[email protected]>---|