2.4.22: Sending data using raw IP. HELP!!
I need to send a data out using raw IP.
For start I tried to send an ICMP response using the code below, but it gives me a error (kernel 2.4.22) and clears the skb buffer without sending it. Please help me to send the data out of the kernel 2.4.22 - I have dstaddr, srcaddr and payload and I know it should go through eth0. I just need somehow push this data out. The data comes from the user space application, shall I consider other options, like to send data from the user space. Can I do this using raw IP? I am very much appreciate for any ideas on how to send data using raw IP.
Please help!!
__the_error__
dstip = ac198c13, 0
eth0h_h_len :: 4
Allocated 48 bytes
Length :: 12ip_finish_output: bad unowned skb(nf_debug=10) = c0794120: POST_ROUTING
skb: pf=2 (unowned) dev=eth0 len=32
PROTO=1 172.25.206.4:0 172.25.140.19:0 L=32 S=0x00 I=0 F=0x4000 T=128 retval :: 0
__the_code__
struct curr_lbts {
int i;
} curr_lbts;
...// __declaration__
struct rt_key key = {.dst = packet->data.dstip, .src=packet->data.srcip}; total_len = sizeof(struct iphdr) + sizeof(struct icmphdr) + sizeof(curr_lbts);
retval = ip_route_output_key(&rt, &key); printk("dstip = %x, %d\n", packet->data.dstip, retval); printk("%s\n", (rt->u.dst.dev)->name);
hh_len = ((rt->u.dst.dev->hard_header_len + 15) & ~15);
printk ("h_h_len :: %d \n", sizeof(curr_lbts)); skb = dev_alloc_skb(total_len + hh_len); printk("Allocated %d bytes \n", total_len + hh_len); skb->priority = 0;skb->dst = dst_clone(&rt->u.dst);
skb_reserve(skb, hh_len);
skb->nh.iph = iph = (struct iphdr *) skb_put(skb,
(sizeof(struct iphdr) +
sizeof(struct icmphdr)));iph->ihl = 5;iph->version = 4;iph->tos = 0x00;iph->tot_len = htons(total_len);iph->id = 0;iph->frag_off = htons(IP_DF);iph->ttl = 128;iph->protocol = IPPROTO_ICMP;iph->saddr = rt->rt_src;iph->daddr = rt->rt_dst;iph->check = 0;iph->check = ip_fast_csum((unsigned char*) iph, iph->ihl);
skb->h.icmph = icmph = (struct icmphdr *)((char *)iph + iph->ihl * 4); icmph->type = ICMP_ECHO;icmph->code = code;icmph->un.echo.id = 0x42;icmph->un.echo.sequence = 0x42;icmph->checksum = 0x0000;printk("Length :: %d \n", total_len - sizeof(struct iphdr));
data = (unsigned char*) icmph + sizeof(struct icmphdr) ; memcpy(skb_put(skb, sizeof(curr_lbts)), &curr_lbts, sizeof(curr_lbts)); icmph->checksum = ip_compute_csum((unsigned char *)icmph,
total_len - (iph->ihl * 4));
retval = rt->u.dst.output(skb);printk("retval :: %d \n", retval);
Em Fri, Dec 26, 2003 at 03:26:56PM +1300, Dmytro Bablinyuk escreveu:
Quoted 4 lines
I need to send a data out using raw IP.
For start I tried to send an ICMP response using the code below, but it gives me a error (kernel 2.4.22) and clears the skb buffer without sending it.
Could you please send this message to the [email protected] mailing list? That is the proper place for these kinds of questions.
Thanks,
- Arnaldo