Skip to contentSkip to conversation

Digigram VX222e not seen as card

DISCUSSION Sam Mulvey 1 participant 1 message Aug 17, 2017

lore
Share & tools
lore

Sam Mulvey

author
#0 lore raw

A radio station I'm working on has a machine with a Digigram VX222e connected to it.

According to the Digigram site and the ALSA website, the sound card is supported by ALSA. Unfortunately, it doesn't appear to be detected as a sound card. Reading online, it requires some firmware, but it appears that my system has the proper firmware installed.

The VX222e is a PCIe card, but it appears to be PCI on the card with a PCIe to PCI bridge. According to Digigram's support site, they made a hardware change in March of 2017, and I suspect that this might be the problem.

I'm guessing it might be as simple enough as an ID match that I need to add to a module, but I've never worked with the card before, and I'm a little stuck.

There's nothing regarding the card in dmesg, but it is visible in lspci:

03:00.0 PCI bridge: PLX Technology, Inc. PEX 8111 PCI Express-to-PCI Bridge (rev 21) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
NUMA node: 0
Bus: primary=03, secondary=04, subordinate=04, sec-latency=32 I/O behind bridge: 0000e000-0000efff [size=4K] Memory behind bridge: fde00000-fdefffff [size=1M] Prefetchable memory behind bridge: fdd00000-fddfffff [size=1M] Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] Express (v1) PCI-Express to PCI/PCI-X Bridge,
MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-

                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,

Exit Latency L0s <1us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Power Budgeting <?>
Kernel modules: shpchp

04:04.0 Multimedia audio controller: PLX Technology, Inc. PCI9056 32-bit 66MHz PCI <-> IOBus Bridge
Subsystem: Digigram Device ba41
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 3
NUMA node: 0
Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=512] Region 1: I/O ports at ec00 [size=256]
Region 2: I/O ports at ef00 [size=128]
Capabilities: [40] Power Management version 0
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] #00 [0000]
Capabilities: [4c] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Input/output error

I'm also documenting what I've got and what I've tried here:
https://vis.nu/blog/digigram_vx222e_isn_t_seen_in_arch_linux

Any pointers would be helpful. Thanks!

-Sam