2.6.1 - IRQ routing regression on Abit VP6

2.6.0 works fine on this hardware, including the twitchy built-in USB controllers.

Loading the uhci-hcd module on 2.6.1 gives me the following:

drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: irq 225, io base 00009400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: irq 225, io base 00009800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 1-0:1.0: new USB device on port 1, assigned address 2
APIC error on CPU1: 00(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU0: 00(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU1: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU0: 40(40)
APIC error on CPU1: 40(40)
irq 177: nobody cared!

Call Trace:
 [<c010d74a>] __report_bad_irq+0x2a/0x90
 [<c010d840>] note_interrupt+0x70/0xb0
 [<c010dc35>] do_IRQ+0x195/0x220
 [<c011b7ed>] smp_apic_timer_interrupt+0xdd/0x150
 [<c0105000>] rest_init+0x0/0x80
 [<c010bc24>] common_interrupt+0x18/0x20
 [<c0108ac0>] default_idle+0x0/0xc0
 [<c0105000>] rest_init+0x0/0x80
 [<c0108a19>] hlt_idle+0x29/0x40
 [<c0108bbb>] cpu_idle+0x3b/0x50
 [<c03aa4a0>] unknown_bootoption+0x0/0x120
 [<c03aa940>] start_kernel+0x1b0/0x200
 [<c03aa4a0>] unknown_bootoption+0x0/0x120

handlers:
[<c0263d00>] (ide_intr+0x0/0x2c0)
[<c0263d00>] (ide_intr+0x0/0x2c0)
Disabling IRQ #177
usb 1-1: control timeout on ep0out
uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Different ACPI or APIC settings may help.

And so on, until I shut down the system.

The 20031203 ACPI patch fixes the problem.

========================================================================
Ian Pilcher                                        [email protected]
========================================================================



-------------------------------------------------------
This SF.net email is sponsored by: Perforce Software.
Perforce is the Fast Software Configuration Management System offering
advanced branching capabilities and atomic changes on 50+ platforms.
Free Eval! http://www.perforce.com/perforce/loadprog.html