serial.c - start looking from 0x220 iomem_base ??
Hi
I am having here a device (Tablet PC ) sample with a serial resistive touchscreen . Under Windows it comes up as COM1 at IO-Base 0x220 -0x227 IRQ 4 .
Now it seems that in linux the serial driver doesnt look for so "low" I/O-Base `s .
By hacking around by hardcoding the 0x220 somehwere in serial.c i get it to detect a standard 16550 , but unfortunately it then assumes that all ttySX have this base .
This is because of my hardcoded hack and the driver not looking for all the rest mem bases.
So the quesion is :
Where do i tell serial.o to start lower ( at 0x220 ) to look for controllers .. .??
Pls also CC me directly since i am only monitoring this list .
Signature · 15 lines
____________________________________ *Robert Woerle * *Technical Product Manager 2L Computers BV* * *Niederlassung Deutschland* *Pace/Blade/ /- /Commodore - Conceptronic* ** * phone: +49 89 552 999 34 fax: +49 89 552 999 10 email: [email protected] <mailto:[email protected]> web: http://www.paceblade.com <http://www.paceblade.com/> _____________________________________
Quoted 14 lines · Robert Woerle
Hi
I am having here a device (Tablet PC ) sample with a serial resistive touchscreen .
Under Windows it comes up as COM1 at IO-Base0x220-0x227 IRQ 4 . Now it seems that in linux the serial driver doesnt look for so "low" I/O-Base `s .By hacking around by hardcoding the
0x220somehwere inserial.ci get it to detect a standard 16550 , but
unfortunately it then assumes that all ttySX have this base . This is because of my hardcoded hack and the driver not looking for all the rest mem bases.
Quoted 7 lines
So the quesion is :
Where do i tell serial.o to start lower ( at0x220) to look for controllers .. .??Pls also CC me directly since i am only monitoring this list .
There are 4 de facto standard serial ports:
COM1 0x3F8 IRQ4
COM2 0x2F8 IRQ3
COM3 0x3E8 IRQ4
COM4 0x2E8 IRQ3
If you have a port at 0x220, it is above the game-port area, but not where the kernel should "look for" serial devices. Therefore, you don't tell the kernel to, as you state, start lower. Instead, you tell the kernel where they are by putting them in the pnp_devices[] table.
Cheers,
Dick Johnson
Penguin : Linux version 2.4.24 on an i686 machine (797.90 BogoMips).
Note 96.31% of all statistics are fiction.
Quoted 35 lines · Richard B. Johnson
Quoted 14 lines · Robert Woerle
Hi
I am having here a device (Tablet PC ) sample with a serial resistive touchscreen .
Under Windows it comes up as COM1 at IO-Base0x220-0x227 IRQ 4 . Now it seems that in linux the serial driver doesnt look for so "low" I/O-Base `s .By hacking around by hardcoding the
0x220somehwere inserial.ci get it to detect a standard 16550 , but
unfortunately it then assumes that all ttySX have this base . This is because of my hardcoded hack and the driver not looking for all the rest mem bases.Quoted 9 lines
So the quesion is :
Where do i tell serial.o to start lower ( at0x220) to look for controllers .. .??Pls also CC me directly since i am only monitoring this list .
There are 4 de facto standard serial ports:
COM1
0x3F8IRQ4
COM20x2F8IRQ3
COM30x3E8IRQ4
COM40x2E8IRQ3
Quoted 9 lines
If you have a port at
0x220, it is above the game-port area, but not where the kernel should "look for" serial devices. Therefore, you don't tell the kernel to, as you state, start lower. Instead, you tell the kernel where they are by putting them in the pnp_devices[] table.
I tryed that now and added a device like ISAPNP_VENDOR('P', 'N', 'P'), ISAPNP_DEVICE(0x0220),
but nothing happens ... it leaves the function saying <7>"Leaving probe_serial_pci() (probe finished)
What can i do ?