Adaptec 1210SA SATA Controller Performance
Hi!
Yesterday I've setup a server with Adaptec's 1210SA SATA Controller and 2 SATA disks. According to the kernel changelog the controller is supported since 2.6.2
I've installed Debian on an IDE disk, built a 2.6.3 kernel with CONFIG_SCSI_SATA_SIL, rebooted and the kernel detected the controller plus both SATA disks (sda, sdb). As the next step I wanted to create a software raid 1 with the 2 SATA disks. Because it took mdadm forever to finish, I checked /proc/mdstat and saw a progress bar with a rate of 12MB/s!
Even my oldest IDE disk is faster than this. Is there a way to tweak the SATA controller/disk with some kernel-options or is the driver not providing more speed?
Any hints?
Thanks..
Patrick
Quoted 10 lines · Patrick Petermair
Yesterday I've setup a server with Adaptec's 1210SA SATA Controller and 2 SATA disks. According to the kernel changelog the controller is supported since 2.6.2
I've installed Debian on an IDE disk, built a 2.6.3 kernel with
CONFIG_SCSI_SATA_SIL, rebooted and the kernel detected the controller plus both SATA disks (sda, sdb). As the next step I wanted to create a software raid 1 with the 2 SATA disks. Because it took mdadm forever to finish, I checked/proc/mdstatand saw a progress bar with a rate of 12MB/s!
Quoted 3 lines
Even my oldest IDE disk is faster than this. Is there a way to tweak the SATA controller/disk with some kernel-options or is the driver not providing more speed?
You don't say what make of disk these are. It may be that you've
fallen foul of the Seagate/SiI erratum, which (as far as I can tell) still kills performance. I have a 120GiB Seagate disk attached to a SiI3112 controller, and I'm lucky if I get 12MiB/s with the IDE-layer driver. I haven't tried the libata driver yet.
I'm not too worried about that set-up, because I don't need massive
performance off that disk anyway, but something faster might be nice. :)
Hugo.
Signature · 4 lines
=== Hugo Mills: hugo@... carfax.org.uk | darksatanic.net | lug.org.uk ===
PGP key: 1C335860 from wwwkeys.eu.pgp.net or http://www.carfax.org.uk
--- Jazz is the sort of music where no-one plays anything the ---
same way once. Quoted 5 lines · Patrick Petermair
Hi!
Yesterday I've setup a server with Adaptec's 1210SA SATA Controller and 2 SATA disks. According to the kernel changelog the controller is supported since 2.6.2
I've installed Debian on an IDE disk, built a 2.6.3 kernel with
CONFIG_SCSI_SATA_SIL, rebooted and the kernel detected the controller plus both SATA disks (sda, sdb). As the next step I wanted to create a software raid 1 with the 2 SATA disks. Because it took mdadm forever to finish, I checked/proc/mdstatand saw a progress bar with a rate of 12MB/s!
Do you have Seagate disks?
Jeff
Quoted 10 lines
Quoted 10 lines
Yesterday I've setup a server with Adaptec's 1210SA SATA Controller and 2 SATA disks. According to the kernel changelog the controller is supported since 2.6.2
I've installed Debian on an IDE disk, built a 2.6.3 kernel with
CONFIG_SCSI_SATA_SIL, rebooted and the kernel detected the controller plus both SATA disks (sda, sdb). As the next step I wanted to create a software raid 1 with the 2 SATA disks. Because it took mdadm forever to finish, I checked/proc/mdstatand saw a progress bar with a rate of 12MB/s!
More to the point, why didn't you just install a 2.4.18 kernel and use the Adaptec-supplied driver and the RAID-1 capabilities built into the card's firmware? (Note, I'm not trying to disparage Jeff's work on libata here.)
I have this setup and it works flawlessly with a pair of 160GB SATA drives.
-Bob
Quoted 5 lines · Bob Glamm
Quoted 3 lines
Quoted 3 lines
Yesterday I've setup a server with Adaptec's 1210SA SATA Controller and 2 SATA disks. According to the kernel changelog the controller is supported since 2.6.2
I've installed Debian on an IDE disk, built a 2.6.3 kernel with
CONFIG_SCSI_SATA_SIL, rebooted and the kernel detected the controller plus both SATA disks (sda, sdb). As the next step I wanted to create a software raid 1 with the 2 SATA disks. Because it took mdadm forever to finish, I checked/proc/mdstatand saw a progress bar with a rate of 12MB/s!
Quoted 7 lines
More to the point, why didn't you just install a 2.4.18 kernel and use the Adaptec-supplied driver and the RAID-1 capabilities built into the card's firmware? (Note, I'm not trying to disparage Jeff's work on libata here.)
I have this setup and it works flawlessly with a pair of 160GB SATA drives.
There are no RAID-1 capabilities built into the card's firmware :)
It's all software RAID.
Jeff
Hi!
Sorry, for replying so late .. was a busy week and didn't have access to the server until today.
Quoted 1 line
Do you have Seagate disks?
Yup, 2 Seagate Barracuda 7200.7 (80GB). Any problems with Seagate and Adaptec 1210SA?
Thanks so far,
Patrick
Quoted 9 lines · Patrick Petermair
Hi!
Sorry, for replying so late .. was a busy week and didn't have access to the server until today.
Quoted 1 line
Do you have Seagate disks?
Yup, 2 Seagate Barracuda 7200.7 (80GB). Any problems with Seagate and Adaptec 1210SA?
Yes.
There is a known problem with Seagate's SATA drives and the SiI
3112 controller that is used on the Adaptec 1210SA. The difficulty is that certain [common] transfer sizes have to be split up into two transfers in order to avoid triggering the erratum (which hangs the machine, IIRC). This drops performance drastically. There is currently no solution to the low performance of the Seagate/SiI combination.
Hugo.
Signature · 4 lines
=== Hugo Mills: hugo@... carfax.org.uk | darksatanic.net | lug.org.uk ===
PGP key: 1C335860 from wwwkeys.eu.pgp.net or http://www.carfax.org.uk
--- Prof Brain had been in search of The Truth for 25 years, with ---
the intention of putting it under house arrest.