KERNEL 2.6.3 and MAXTOR 160 GB
A message that is not in the archive (sent off-list or not yet received): [email protected]
Sorry my stupid mistake .. this is the correct message from boot:
Thanks for any reply!!
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:04.0
ACPI: No IRQ known for interrupt pin A of device 0000:00:04.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:piohda: Maxtor 6Y160P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: no response (status = 0xa1), resetting drive
hdc: no response (status = 0xa1)
hdd: no response (status = 0xa1), resetting drive
hdd: no response (status = 0xa1)
hdc: no response (status = 0xa1), resetting drive
hdc: no response (status = 0xa1)
hdd: no response (status = 0xa1), resetting drive
hdd: no response (status = 0xa1)
hda: max request size: 128KiB
hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
ide-floppy driver 0.99.newide
Console: switching to colour frame buffer device 100x37
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0 Advanced Linux Sound Architecture Driver Version 1.0.2c (Thu Feb 05 15:41:49 2004 UTC).
ALSA device list:
#0: C-Media PCI CMI8738-MC6 (model 55) at 0xb000, irq 9
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536) IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driverip_conntrack version 2.1 (6143 buckets, 49144 max) - 300 bytes per conntrackip_tables: (C) 2000-2002 Netfilter core teamipt_recent v0.3.1: Stephen Frost <[email protected]>.
http://snowman.net/projects/ipt_recent/arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 272k freed drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hubohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)ohci_hcd: block sizes: ed 64 td 64ohci_hcd 0000:00:02.0: OHCI Host Controllerohci_hcd 0000:00:02.0: irq 9, pci mem f1864000ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detectedohci_hcd 0000:00:06.0: OHCI Host Controllerohci_hcd 0000:00:06.0: irq 9, pci mem f1866000ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detecteddrivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver drivers/usb/core/usb.c: registered new driver usbkbd drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver drivers/usb/core/usb.c: registered new driver usbmouse
Here is the .config of kernel (ATA section)
# ATA/ATAPI/MFM/RLL support
#CONFIG_IDE=yCONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives #
# CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_IDEDISK_STROKE=yCONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set CONFIG_BLK_DEV_IDEFLOPPY=yCONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_IDE_TASKFILE_IO is not set
#
# IDE chipset support/bugfixes
#CONFIG_IDE_GENERIC=yCONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not setCONFIG_BLK_DEV_IDEPNP=yCONFIG_BLK_DEV_IDEPCI=yCONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not setCONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not setCONFIG_BLK_DEV_RZ1000=yCONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not setCONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not setCONFIG_BLK_DEV_ADMA=yCONFIG_BLK_DEV_AEC62XX=yCONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not setCONFIG_BLK_DEV_AMD74XX=yCONFIG_BLK_DEV_CMD64X=yCONFIG_BLK_DEV_TRIFLEX=yCONFIG_BLK_DEV_CY82C693=y
# CONFIG_BLK_DEV_CS5520 is not setCONFIG_BLK_DEV_CS5530=yCONFIG_BLK_DEV_HPT34X=y
# CONFIG_HPT34X_AUTODMA is not setCONFIG_BLK_DEV_HPT366=yCONFIG_BLK_DEV_SC1200=yCONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not setCONFIG_BLK_DEV_PDC202XX_OLD=y
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not setCONFIG_BLK_DEV_SVWKS=yCONFIG_BLK_DEV_SIIMAGE=yCONFIG_BLK_DEV_SIS5513=yCONFIG_BLK_DEV_SLC90E66=yCONFIG_BLK_DEV_TRM290=yCONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not setCONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not setCONFIG_IDEDMA_AUTO=y
# CONFIG_DMA_NONPCI is not set
# CONFIG_BLK_DEV_HD is not set
Carlo,
From the driver code:
/* Don't use LBA48 on ALi devices before rev 0xC5 */ hwif->no_lba48 = (m5229_revision <= 0xC4) ? 1 : 0;
0xC5 is revision 197 your system has a revision 196 chipset.
The inabilty to use LBA48 with that chipset version is why Linux is saying:
hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63,
and restricting you to use only 137 GB of that drive.
2.6 knows it is a 160GB drive but the chipset can't handle anything above 137GB.
Cheers,
Dave
Quoted 146 lines · Carlo Orecchia
Sorry my stupid mistake .. this is the correct message from boot:
Thanks for any reply!!ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:04.0
ACPI: No IRQ known for interrupt pin A of device 0000:00:04.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs lateride0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:piohda: Maxtor 6Y160P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: no response (status =0xa1), resetting drive
hdc: no response (status =0xa1)
hdd: no response (status =0xa1), resetting drive
hdd: no response (status =0xa1)
hdc: no response (status =0xa1), resetting drive
hdc: no response (status =0xa1)
hdd: no response (status =0xa1), resetting drive
hdd: no response (status =0xa1)
hda: max request size: 128KiB
hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
ide-floppy driver 0.99.newide
Console: switching to colour frame buffer device 100x37
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
input: PC Speaker
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.2c (Thu Feb 05 15:41:49 2004 UTC). ALSA device list:
#0: C-Media PCI CMI8738-MC6 (model 55) at0xb000, irq 9
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driverip_conntrackversion 2.1 (6143 buckets, 49144 max) - 300 bytes per conntrackip_tables: (C) 2000-2002 Netfilter core teamipt_recentv0.3.1: Stephen Frost <[email protected]>. http://snowman.net/projects/ipt_recent/arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 272k freeddrivers/usb/core/usb.c: registered new driver usbfsdrivers/usb/core/usb.c: registered new driver hubohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)ohci_hcd: block sizes: ed 64 td 64ohci_hcd0000:00:02.0: OHCI Host Controllerohci_hcd0000:00:02.0: irq 9, pci memf1864000ohci_hcd0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detectedohci_hcd0000:00:06.0: OHCI Host Controllerohci_hcd0000:00:06.0: irq 9, pci memf1866000ohci_hcd0000:00:06.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detecteddrivers/usb/core/usb.c: registered new driver hiddrivers/usb/input/hid-core.c: v2.0:USB HID core driverdrivers/usb/core/usb.c: registered new driver usbkbddrivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driverdrivers/usb/core/usb.c: registered new driver usbmouseHere is the .config of kernel (ATA section)
# ATA/ATAPI/MFM/RLL support
#CONFIG_IDE=yCONFIG_BLK_DEV_IDE=y#
# Please seeDocumentation/ide.txtfor help/info on IDE drives #
#CONFIG_BLK_DEV_HD_IDEis not setCONFIG_BLK_DEV_IDEDISK=yCONFIG_IDEDISK_MULTI_MODE=yCONFIG_IDEDISK_STROKE=yCONFIG_BLK_DEV_IDECD=y
#CONFIG_BLK_DEV_IDETAPEis not setCONFIG_BLK_DEV_IDEFLOPPY=yCONFIG_BLK_DEV_IDESCSI=y
#CONFIG_IDE_TASK_IOCTLis not set
#CONFIG_IDE_TASKFILE_IOis not set#
# IDE chipset support/bugfixes
#CONFIG_IDE_GENERIC=yCONFIG_BLK_DEV_CMD640=y
#CONFIG_BLK_DEV_CMD640_ENHANCEDis not setCONFIG_BLK_DEV_IDEPNP=yCONFIG_BLK_DEV_IDEPCI=yCONFIG_IDEPCI_SHARE_IRQ=y
#CONFIG_BLK_DEV_OFFBOARDis not setCONFIG_BLK_DEV_GENERIC=y
#CONFIG_BLK_DEV_OPTI621is not setCONFIG_BLK_DEV_RZ1000=yCONFIG_BLK_DEV_IDEDMA_PCI=y
#CONFIG_BLK_DEV_IDEDMA_FORCEDis not setCONFIG_IDEDMA_PCI_AUTO=y
#CONFIG_IDEDMA_ONLYDISKis not setCONFIG_BLK_DEV_ADMA=yCONFIG_BLK_DEV_AEC62XX=yCONFIG_BLK_DEV_ALI15X3=y
#CONFIG_WDC_ALI15X3is not setCONFIG_BLK_DEV_AMD74XX=yCONFIG_BLK_DEV_CMD64X=yCONFIG_BLK_DEV_TRIFLEX=yCONFIG_BLK_DEV_CY82C693=y
#CONFIG_BLK_DEV_CS5520is not setCONFIG_BLK_DEV_CS5530=yCONFIG_BLK_DEV_HPT34X=y
#CONFIG_HPT34X_AUTODMAis not setCONFIG_BLK_DEV_HPT366=yCONFIG_BLK_DEV_SC1200=yCONFIG_BLK_DEV_PIIX=y
#CONFIG_BLK_DEV_NS87415is not setCONFIG_BLK_DEV_PDC202XX_OLD=y
#CONFIG_PDC202XX_BURSTis not set
#CONFIG_BLK_DEV_PDC202XX_NEWis not setCONFIG_BLK_DEV_SVWKS=yCONFIG_BLK_DEV_SIIMAGE=yCONFIG_BLK_DEV_SIS5513=yCONFIG_BLK_DEV_SLC90E66=yCONFIG_BLK_DEV_TRM290=yCONFIG_BLK_DEV_VIA82CXXX=y
#CONFIG_IDE_CHIPSETSis not setCONFIG_BLK_DEV_IDEDMA=y
#CONFIG_IDEDMA_IVBis not setCONFIG_IDEDMA_AUTO=y
#CONFIG_DMA_NONPCIis not set
#CONFIG_BLK_DEV_HDis not set
Quoted 12 lines · Carlo Orecchia
Sorry my stupid mistake .. this is the correct message from boot:
Thanks for any reply!!ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:04.0
ACPI: No IRQ known for interrupt pin A of device 0000:00:04.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs lateride0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
Quoted 14 lines
hda: Maxtor 6Y160P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: no response (status =0xa1), resetting drive
hdc: no response (status =0xa1)
hdd: no response (status =0xa1), resetting drive
hdd: no response (status =0xa1)
hdc: no response (status =0xa1), resetting drive
hdc: no response (status =0xa1)
hdd: no response (status =0xa1), resetting drive
hdd: no response (status =0xa1)
hda: max request size: 128KiB
hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63, UDMA(100)
Your IDE controller doesn't support DMA transfer modes when LBA48 is used. This means that access to the > 137GB part of the disk can only be done using PIO modes (slow!).
Patch below (against kernel 2.6.4-rc2) should fix access to >137GB part of the disk in the best possible way - IDE driver will always try to use DMA and revert to PIO only when necessary. I dunno what patches are included in RedHat's 2.4.20-8 but kernels < 2.4.23 can silently corrupt your data because of this issue (and you still won't access whole disk with >= 2.4.23, although -ac tree contained fix which just turned DMA off).
Quoted 1 line
#
CONFIG_IDE_TASKFILE_IOis not set
Please don't set it to 'y' while using this patch (because it's harder to fix for CONFIG_IDE_TASKFILE_IO and conflicts with other pending patches).
Regards,
Bartlomiej
linux-2.6.4-rc2-root/drivers/ide/ide-disk.c | 29 +++++++++++++++++------- linux-2.6.4-rc2-root/drivers/ide/ide-probe.c | 8 ++++-- linux-2.6.4-rc2-root/drivers/ide/pci/alim15x3.c | 4 +-- linux-2.6.4-rc2-root/include/linux/ide.h | 1 4 files changed, 30 insertions(+), 12 deletions(-)
drivers/ide/ide-disk.c renamed from drivers/ide/ide-disk.c~ide_no_lba48_dma +21 -8
@@ -470,12 +470,15 @@ ide_startstop_t __ide_do_rw_disk (ide_dr }if (rq_data_dir (rq) ==READ ) { +if (!drive->hwif->no_lba48_dma || + rq->sector + rq->nr_sectors <1ULL <<28 ) {#ifdef CONFIG_BLK_DEV_IDE_TCQ -if (blk_rq_tagged (rq)) -return __ide_dma_queued_read (drive); +if (blk_rq_tagged (rq)) +return __ide_dma_queued_read (drive);#endif -if (drive->using_dma && !hwif->ide_dma_read (drive)) -return ide_started; +if (drive->using_dma && !hwif->ide_dma_read (drive)) +return ide_started; + } command = ((drive->mult_count) ? ((lba48) ? WIN_MULTREAD_EXT : WIN_MULTREAD) :
@@ -484,12 +487,16 @@ ide_startstop_t __ide_do_rw_disk (ide_drreturn ide_started; }else if (rq_data_dir (rq) ==WRITE ) {ide_startstop_t startstop; + +if (!drive->hwif->no_lba48_dma || + rq->sector + rq->nr_sectors <1ULL <<28 ) {#ifdef CONFIG_BLK_DEV_IDE_TCQ -if (blk_rq_tagged (rq)) -return __ide_dma_queued_write (drive); +if (blk_rq_tagged (rq)) +return __ide_dma_queued_write (drive);#endif -if (drive->using_dma && !(HWIF (drive)->ide_dma_write (drive))) -return ide_started; +if (drive->using_dma && !hwif->ide_dma_write (drive)) +return ide_started; + } command = ((drive->mult_count) ? ((lba48) ? WIN_MULTWRITE_EXT : WIN_MULTWRITE) :
@@ -1601,6 +1608,12 @@ static void idedisk_setup (ide_drive_t * drive->capacity64 =1ULL <<28 ; } +if (drive->hwif->no_lba48_dma && drive->capacity64 >1ULL <<28 ) { +printk (KERN_INFO "%s: cannot use LBA48 DMA - PIO mode will be" +"used for accessing sectors > %u\n" , + drive->name,1 <<28 ); + } +/* * if possible, give fdisk access to more of the drive, * by correcting bios_cyls:
drivers/ide/ide-probe.c renamed from drivers/ide/ide-probe.c~ide_no_lba48_dma +6 -2
@@ -922,8 +922,12 @@ static int ide_init_queue(ide_drive_t *d q->queuedata =HWGROUP (drive);blk_queue_segment_boundary (q,0xffff ); -if (!hwif->rqsize) - hwif->rqsize = hwif->no_lba48 ?256 :65536 ; +if (!hwif->rqsize) { +if (hwif->no_lba48 || hwif->no_lba48_dma) + hwif->rqsize =256 ; +else + hwif->rqsize =65536 ; + }if (hwif->rqsize < max_sectors) max_sectors = hwif->rqsize;blk_queue_max_sectors (q, max_sectors);
drivers/ide/pci/alim15x3.c renamed from drivers/ide/pci/alim15x3.c~ide_no_lba48_dma +2 -2
@@ -752,8 +752,8 @@ static void __init init_hwif_common_ali1 hwif->tuneproc = &ali15x3_tune_drive; hwif->speedproc = &ali15x3_tune_chipset; -/* Don't use LBA48 on ALi devices before rev 0xC5 */ - hwif->no_lba48 = (m5229_revision <=0xC4 ) ?1 :0 ; +/* don't use LBA48 DMA on ALi devices before rev 0xC5 */ + hwif->no_lba48_dma = (m5229_revision <=0xC4 ) ?1 :0 ;if (!hwif->dma_base) { hwif->drives[0 ].autotune =1 ;
include/linux/ide.h renamed from include/linux/ide.h~ide_no_lba48_dma +1 -0
@@ -980,6 +980,7 @@ typedef struct hwif_s { unsigned autodma : 1; /* auto-attempt using DMA at boot */ unsigned udma_four : 1; /* 1=ATA-66 capable, 0=default */ unsigned no_lba48 : 1; /* 1 = cannot do LBA48 */ + unsigned no_lba48_dma : 1; /* 1 = cannot do LBA48 DMA */ unsigned no_dsc : 1; /* 0 default, 1 dsc_overlap disabled */ unsigned auto_poll : 1; /* supports nop auto-poll */
_