Skip to contentSkip to conversation

2.6.3 ifdown race

DISCUSSION Francis F Steen 2 participants 2 messages Mar 16, 2004

lore
Share & tools
lore
#0 lore raw

In kernel 2.6.3, if I take down the network connection, within a second or so top shows 99.9% CPU utilization for [events/0]. When I restablish a network connection, it calms down at once.

I had the same behavior in 2.6.0.

Details below -- what can I do to get more information on what is happening?

Cheers,
David

(Please cc: me)

#lspci
00:00.0 Host bridge: ALi Corporation M1671 Super P4 Northbridge [AGP4X,PCI and SDR/DDR] (rev 02) 00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02) 00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
00:08.0 Modem: ALi Corporation Intel 537 [M5457 AC-Link Modem]
00:09.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01) 00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02) 00:0b.0 USB Controller: VIA Technologies, Inc. USB (rev 50)
00:0b.1 USB Controller: VIA Technologies, Inc. USB (rev 50)
00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51)
00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) 00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
00:11.0 Bridge: ALi Corporation M7101 PMU
00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420 Go 32M] (rev a3)

#dmesg

natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <[email protected]>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
eth0: NatSemi DP8381[56] at 0xe089d000, 00:c0:9f:15:0f:59, IRQ 5.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
eth0: remaining active for wake-on-lan
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.

# ifdown eth0
# top

3 root 15 -10 0 0 0 R 99.9 0.0 4:06.09 events/0

# ps aux | grep events

root 3 0.0 0.0 0 0 ? RW< Mar14 1:00 [events/0]

#1 lore raw
Quoted 7 lines · Francis F Steen

In kernel 2.6.3, if I take down the network connection, within a second or so top shows 99.9% CPU utilization for [events/0].
When I restablish a network connection, it calms down at once.

I had the same behavior in 2.6.0.

Details below -- what can I do to get more information on what is happening?

Compile in CONFIG_MAGIC_SYSRQ and then when the load goes up do;

alt + syrq + t

you're interested in the call traces from events/0