Problems after waking up from S3 (mainly network related)
Hi,
sorry for bothering and for this lengthy email, but quite a few days searching the web and usenet has not helped a lot in solving this issue:
On my Asus A7V Motherboard (BIOS 1011) I'm running 2.6.4 with the according acpi4linux patches. Everything is quite ok, I can suspend to RAM and wake the box back up via /proc/acpi/alarm or the power button.
However, after waking up the onboard Promise IDE Controller PDC20... as well as the SIS900 based network card did not work, e.g.
Mar 22 21:32:34 daisy kernel: Stopping tasks: ==========================================|
Mar 22 21:32:34 daisy kernel: hde: start_power_step(step: 0)
Mar 22 21:32:34 daisy kernel: hde: start_power_step(step: 1)
Mar 22 21:32:34 daisy kernel: hde: complete_power_step(step: 1, stat: 50, err: 0)
Mar 22 21:32:34 daisy kernel: hde: completing PM request, suspend
Mar 22 21:32:34 daisy kernel: hdd: start_power_step(step: 0)
Mar 22 21:32:34 daisy kernel: hdd: completing PM request, suspend
Mar 22 21:32:34 daisy kernel: hda: start_power_step(step: 0)
Mar 22 21:32:34 daisy kernel: hda: start_power_step(step: 1)
Mar 22 21:32:34 daisy kernel: hda: complete_power_step(step: 1, stat: 50, err: 0)
Mar 22 21:32:34 daisy kernel: hda: completing PM request, suspend
Mar 22 21:32:34 daisy kernel: hwsleep-0300 [18] acpi_enter_sleep_state: Entering sleep state [S3]
Mar 22 21:32:34 daisy kernel: eth0: Media Link Off
Mar 22 21:32:34 daisy kernel: hda: Wakeup request inited, waiting for !BSY...
Mar 22 21:32:34 daisy kernel: hda: start_power_step(step: 1000)
Mar 22 21:32:34 daisy kernel: blk: queue c7ef3c00, I/O limit 4095Mb (mask 0xffffffff)
Mar 22 21:32:34 daisy kernel: hda: completing PM request, resume
Mar 22 21:32:34 daisy kernel: hdd: Wakeup request inited, waiting for !BSY...
Mar 22 21:32:34 daisy kernel: hdd: start_power_step(step: 1000)
Mar 22 21:32:34 daisy kernel: hdd: completing PM request, resume
Mar 22 21:32:34 daisy kernel: hde: Wakeup request inited, waiting for !BSY...
Mar 22 21:32:34 daisy kernel: hde: start_power_step(step: 1000)
Mar 22 21:32:34 daisy kernel: blk: queue c7ee1c00, I/O limit 4095Mb (mask 0xffffffff)
Mar 22 21:32:34 daisy kernel: hde: completing PM request, resume
Mar 22 21:32:34 daisy kernel: Restarting tasks... done
Mar 22 21:32:42 daisy kernel: MCE: The hardware reports a non fatal, correctable incident occurred on CPU 0.
Mar 22 21:32:42 daisy kernel: Bank 1: ddd1ffdd220010b5
Mar 22 21:32:42 daisy kernel: MCE: The hardware reports a non fatal, correctable incident occurred on CPU 0.
Mar 22 21:32:42 daisy kernel: Bank 2: b0006000000210ae
Mar 22 21:33:23 daisy kernel: hde: dma_timer_expiry: dma status == 0x24
Mar 22 21:33:33 daisy kernel: PDC202XX: Primary channel reset.
Mar 22 21:33:33 daisy kernel: PDC202XX: Secondary channel reset.
Mar 22 21:33:33 daisy kernel: hde: DMA interrupt recovery
Mar 22 21:33:33 daisy kernel: hde: lost interrupt
Mar 22 21:33:33 daisy kernel: hde: dma_intr: status=0x50 { DriveReady SeekComplete }
Mar 22 21:33:33 daisy kernel:
Mar 22 21:33:33 daisy kernel: hde: status error: status=0x51 { DriveReady SeekComplete Error }
Mar 22 21:33:33 daisy kernel: hde: status error: error=0x04 { DriveStatusError }
...
as well as
...
Mar 23 19:46:23 daisy kernel: eth0: Media Link On 100mbps full-duplex
Mar 23 19:46:38 daisy kernel: NETDEV WATCHDOG: eth0: transmit timed out
Mar 23 19:46:38 daisy kernel: eth0: Transmit timeout, status 00000004 00000240I tested it with and without apic support (with and without io-apic), but nothing changed.
Finally I changed my approach slightly, connecting the single hard drive
to the second IDE channel (VIA KT), which got me rid off the nasty hde
problem. Additionally I tried to disable the network completely (ifconfig eth0 down), unloading the sis900.ko before going to S3.
After waking the box up, I re-inserted the sis900 module (which was answered by
Mar 24 12:44:23 daisy kernel: sis900.c: v1.08.07 11/02/2003 Mar 24 12:44:23 daisy kernel: eth0: SiS 900 Internal MII PHY transceiver found at address 1. Mar 24 12:44:23 daisy kernel: eth0: Using transceiver found at address 1 as default Mar 24 12:44:23 daisy kernel: eth0: SiS 900 PCI Fast Ethernet at 0xa400, IRQ 12, 00:30:ab:01:7b:6e.
) and re-enabling the network settings via ifconfig (answer: eth0: Media Link On 100mbps full-duplex), I still had no network, i.e. trying to ping the interface itself or any other external box had no result except new Transmit timeouts as before without the unloading/loading hassle.
Unfortunately, the very same happened when using a 3c905TXM (with the appropriate module of course ;-)).
Anyone here on the devel list, who can give me a clue (or need more input from my side (i.e. full ACPI tables, etc) how to get around this?
Thanks a lot in advance
Carsten
PS: Please Cc me for a fast reply, but I will monitor the list-archive closely as well.
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click