How do create a dummy device for recording audio? Does it exist already?
Hello,
I've looked through the archives and I couldn't find what I'm
looking for, so here goes:
I'd like to create a dummy audio device that can record the PCM data written to it into a file. So, the dummy device would appear as a sound card to the audio program (Real Player for example), and start dumping audio into a file, or maybe it would create another device that could be read simply by 'dd' or some custom command. Then I'd pipe the data into an MP3 or OGG encoder, split into 1/2 hour chunks, or whatever length chunks I like.
Once the system is running, I'd do something like this:
1) Open my Player, tune to my favorite station. Use my new device for audio output.
2) do something like: dd if=/dev/audiocapturepcmout count=xxx | lame --output myfile.mp3
What would it take to make a alsa drive that captures the PCM data into a file? How about one that captures it, then pumps it into a new /dev/ device for reading?
Thanks,
-Caleb
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 4 lines
1) Open my Player, tune to my favorite station. Use my new device for audio output.
2) do something like: dd if=/dev/audiocapturepcmout count=xxx | lame --output myfile.mp3
streamripper is a much better option for this. its specially designed for this task. you are also talking about mp3->PCM->mp3 conversion, which is not very nice for audio quality.
--p
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
StreamRipper: Close, but no cigar. That only works for MP3 streams, not for other streams, such as RealPlayer. I have looked at streamripper before and it doesn't do what I want as far as I can tell. In the case of RealPlayer, the audio goes from Real->PCM->MP3, which I admit isn't great for audio quality, but I don't really care, I'm not trying to listen to music. In fact, that would be an extraordinarily hard way to get music. I actually want it mainly so that I can record NPR constantly and have 30 minutes blocks automatically encoded and sitting on my hard drive. Then when I come in to a show half way, and what to hear the whole thing, I just grab the files and burn them to MP3 CD. Then I can listen to CarTalk or whatever whenever I want, on my terms.
Quoted 6 lines · Paul Davis
Quoted 5 lines
1) Open my Player, tune to my favorite station. Use my new device for audio output.
2) do something like: dd if=/dev/audiocapturepcmout count=xxx | lame --output myfile.mp3
Quoted 10 lines
streamripper is a much better option for this. its specially designed for this task. you are also talking about
mp3->PCM->mp3conversion, which is not very nice for audio quality.--p
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 3 lines · Caleb Crome
I'd like to create a dummy audio device that can record the PCM data written to it into a file. So, the dummy device would appear as a sound card to the audio program (Real Player for example), and start dumping
How about 'file' type plugin? For example:
pcm.file {
type file
slave {
pcm "hw:0,0"
}
file "/tmp/file.raw"
} Quoted 2 lines
audio into a file, or maybe it would create another device that could be read simply by 'dd' or some custom command. Then I'd pipe the data into
It works with named pipes as well.
http://www.alsa-project.org/alsa-doc/alsa-lib/pcm_plugins.html#pcm_plugins_file
Arek
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
Arek,
That looks like what I want. However, I'm sorry to be such an
ignoramus -- what do I do with that bit of configuration data? I found the /usr/share/alsa/alsa.conf, and there is a similar pcm.file entry in that, but it seems to take parameters. Since I have no sound card, how do I configure my system to use the dummy PCM driver and use the pcm.file plugin?
Sorry to the developer community -- this is a user question. I'll move the thread over there if it continues on.
Thanks,
-Caleb
Quoted 30 lines · Arek Korbik
Quoted 3 lines · Caleb Crome
I'd like to create a dummy audio device that can record the PCM data written to it into a file. So, the dummy device would appear as a sound card to the audio program (Real Player for example), and start dumping
How about 'file' type plugin? For example:
pcm.file { type file slave { pcm "hw:0,0" } file "/tmp/file.raw" }Quoted 3 lines
audio into a file, or maybe it would create another device that could be read simply by 'dd' or some custom command. Then I'd pipe the data into
It works with named pipes as well.
http://www.alsa-project.org/alsa-doc/alsa-lib/pcm_plugins.html#pcm_plugins_file
Arek
Quoted 12 lines
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
At Thu, 22 Apr 2004 14:24:30 -0700,
Quoted 8 lines · Caleb Crome
Arek,
That looks like what I want. However, I'm sorry to be such an
ignoramus -- what do I do with that bit of configuration data? I found the/usr/share/alsa/alsa.conf, and there is a similar pcm.file entry in that, but it seems to take parameters. Since I have no sound card, how do I configure my system to use the dummy PCM driver and use the pcm.file plugin?
you can specify the filename as the parameter of file plugin. for example,
% aplay -Dfile:foo.raw bar.wav
will dump bar.wav as the raw sample data to a new file foo.raw.
Takashi
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
Quoted 9 lines · Caleb Crome
Quoted 7 lines · Arek Korbik
pcm.file { type file slave { pcm "hw:0,0" } file "/tmp/file.raw" }
Quoted 3 lines
what do I do with that bit of configuration data? I found the
/usr/share/alsa/alsa.conf, and there is a similar pcm.file entry in that, but it seems to take parameters.
Put it into your ~/.asoundrc file, or into /etc/asound.conf for all users.
Quoted 2 lines
Since I have no sound card, how do I configure my system to use the dummy PCM driver and use the pcm.file plugin?
"modprobe snd-dummy" should work.
HTH
Clemens
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 62 lines · Caleb Crome
Alright, I did what you suggested, and real player comes up and connects to the dummy sound card (I had to do a modprobe snd-pcm-oss and snd-mixer-oss). However, I don't get a file called
/tmp/file.raw. Is there any way to check how the data is routed? Do I have to do anything to make .asoundrc get reread?Thanks again,
-CalebQuoted 52 lines · Clemens Ladisch
Quoted 12 lines · Caleb Crome
Quoted 8 lines · Arek Korbik
pcm.file {
type fileslave { pcm "hw:0,0"}
file "/tmp/file.raw"
}Quoted 4 lines
what do I do with that bit of configuration data? I found the
/usr/share/alsa/alsa.conf, and there is a similar pcm.file entry in that, but it seems to take parameters.Put it into your ~/.asoundrc file, or into
/etc/asound.conffor all users.Quoted 3 lines
Since I have no sound card, how do I configure my system to use the dummy PCM driver and use the pcm.file plugin?
"modprobe snd-dummy" should work.
HTH
Clemens-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
_______________________________________________
Alsa-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
Quoted 11 lines · Caleb Crome
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
pcm.file {
type fileslave { pcm "hw:0,0"}
file "/tmp/file.raw"
}Alright, I did what you suggested, and real player comes up and connects to the dummy sound card (I had to do a modprobe snd-pcm-oss and
snd-mixer-oss). However, I don't get a file called/tmp/file.raw.
You have to configure the program to use the PCM named "file" instead of the default "default".
However, Realplayer uses the OSS emulation through /dev/dsp0. To make that work with your "file" device, add the following to the config file:
pcm.dsp0 = file
and try to run realplayer with the aoss script from the alsa-oss package.
HTH
Clemens
-------------------------------------------------------
This SF.net email is sponsored by: The Robotic Monkeys at ThinkGeek For a limited time only, get FREE Ground shipping on all orders of $35 or more. Hurry up and shop folks, this offer expires April 30th!
http://www.thinkgeek.com/freeshipping/?cpg=12297
Quoted 25 lines · Clemens Ladisch
Quoted 9 lines · Caleb Crome
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
pcm.file {
type fileslave { pcm "hw:0,0"}
file "/tmp/file.raw"
}Quoted 5 lines
Alright, I did what you suggested, and real player comes up and connects to the dummy sound card (I had to do a modprobe snd-pcm-oss and
snd-mixer-oss). However, I don't get a file called/tmp/file.raw.You have to configure the program to use the PCM named "file" instead of the default "default".
However, Realplayer uses the OSS emulation through
/dev/dsp0. To make that work with your "file" device, add the following to the config file:
Quoted 12 lines
pcm.dsp0 = file
and try to run realplayer with the aoss script from the alsa-oss package.
HTH
Clemens
Awesome! It works like a charm. Than you so much! The one thing that doesn't work quite right is that I get the following error when RealPlayer attempts to access the mixer:
ALSA lib control.c:601:(snd_ctl_open_noupdate) Invalid CTL mixer0
Is there a simple way to get it to control the mixer? Currently, I have to bring up alsamixergui to turn up the volume.
Thanks again,
-Caleb Crome
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click
Quoted 5 lines · Caleb Crome
Quoted 4 lines · Clemens Ladisch
However, Realplayer uses the OSS emulation through
/dev/dsp0. To make that work with your "file" device, add the following to the config file:
Quoted 7 lines
Quoted 1 line
pcm.dsp0 = file
Awesome! It works like a charm. Than you so much! The one thing that doesn't work quite right is that I get the following error when RealPlayer attempts to access the mixer:
ALSA lib control.c:601:(snd_ctl_open_noupdate) Invalid CTL mixer0
It tries to use /dev/mixer0, too. Add the following:
ctl.mixer0 = "hw:0"
HTH
Clemens
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click
Quoted 21 lines · Clemens Ladisch
Quoted 7 lines · Caleb Crome
Quoted 4 lines · Clemens Ladisch
However, Realplayer uses the OSS emulation through
/dev/dsp0. To make that work with your "file" device, add the following to the config file:Quoted 10 lines
Quoted 3 lines
pcm.dsp0 = file
Awesome! It works like a charm. Than you so much! The one thing that doesn't work quite right is that I get the following error when RealPlayer attempts to access the mixer:
ALSA lib control.c:601:(snd_ctl_open_noupdate) Invalid CTL mixer0
Quoted 11 lines
It tries to use
/dev/mixer0, too. Add the following:ctl.mixer0 = "hw:0"
HTH
Clemens
Clemens,
Thanks for the info, however now I get the following:
ALSA lib control.c:516:(snd_ctl_open_conf) Invalid type for CTL mixer0 definition
Any ideas? Just for the record, my asoundrc is:
pcm.dsp0 = file
pcm.file {
type file
slave {
pcm "hw:0,0"
} file "/tmp/pcm.raw.pipe"
}
ctl.mixer0 = "hw:0"
When I changed the last line to:
ctl.mixer0 = hw
it doesn't complain any more. Is that the correct syntax?
Thanks again,
-Caleb
-------------------------------------------------------
This SF.Net email is sponsored by: Oracle 10g
Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE.
http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click