Skip to contentSkip to conversation

2.4.27-pre2-pac1

DISCUSSION O.Sezer 1 participant 1 message May 6, 2004

Subsystems (7)
lore
Share & tools
lore

O.Sezer

author
#0 lore raw

Hello:

You may want to apply the attached patch which
removes double/obsolete entries, makes some minor
name clarifications.

Regards;
Özkan Sezer

Documentation/Configure.help +0 -12
diff -urN 27p2.pac/Documentation/Configure.help 27p2.acx/Documentation/Configure.help
@@ -12532,18 +12532,6 @@
   <file:Documentation/networking/net-modules.txt>.  The module will be
   called forcedeth.o.
 
-Reverse Engineered nForce Ethernet support (EXPERIMENTAL)
-CONFIG_FORCEDETH
-  If you have a network (Ethernet) controller of this type, say Y and
-  read the Ethernet-HOWTO, available from
-  <http://www.tldp.org/docs.html#howto>.
-
-  If you want to compile this as a module ( = code which can be
-  inserted in and removed from the running kernel whenever you want),
-  say M here and read <file:Documentation/modules.txt> as well as
-  <file:Documentation/networking/net-modules.txt>.  The module will be
-  called forcedeth.
-
 CS89x0 support (Daynaport CS and LC cards)
 CONFIG_CS89x0
   Support for CS89x0 chipset based Ethernet cards. If you have a
drivers/ide/pci/atiixp.c +2 -0
diff -urN 27p2.pac/drivers/ide/pci/atiixp.c 27p2.acx/drivers/ide/pci/atiixp.c
@@ -519,4 +519,6 @@
 MODULE_DESCRIPTION("PCI driver module for ATI IXP IDE");
 MODULE_LICENSE("GPL");
 
+MODULE_DEVICE_TABLE(pci, atiixp_pci_tbl);
+
 EXPORT_NO_SYMBOLS;
drivers/ide/pci/piix.h +0 -14
diff -urN 27p2.pac/drivers/ide/pci/piix.h 27p2.acx/drivers/ide/pci/piix.h
@@ -333,20 +333,6 @@
 		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}},
 		.bootable	= ON_BOARD,
 		.extra		= 0,
-	},{	/* 19 */
-		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_ESB_2,
-		.name		= "ESB",
-		.init_setup	= init_setup_piix,
-		.init_chipset	= init_chipset_piix,
-		.init_iops	= NULL,
-		.init_hwif	= init_hwif_piix,
-		.init_dma	= init_dma_piix,
-		.channels	= 2,
-		.autodma	= AUTODMA,
-		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}},
-		.bootable	= ON_BOARD,
-		.extra		= 0,
 	},{
 		.vendor		= 0,
 		.device		= 0,
drivers/scsi/Config.in +0 -5
diff -urN 27p2.pac/drivers/scsi/Config.in 27p2.acx/drivers/scsi/Config.in
@@ -40,11 +40,6 @@
    dep_tristate 'DEC SII Scsi Driver' CONFIG_SCSI_DECSII $CONFIG_SCSI $CONFIG_MIPS32
 fi
 
-dep_mbool 'SATA support' CONFIG_SCSI_ATA $CONFIG_SCSI
-#dep_bool '  Parallel ATA support' CONFIG_SCSI_ATA_PATA $CONFIG_SCSI_ATA
-dep_tristate '  Intel PIIX/ICH support' CONFIG_SCSI_ATA_PIIX $CONFIG_SCSI_ATA $CONFIG_PCI
-dep_tristate '  VIA SATA support' CONFIG_SCSI_SATA_VIA $CONFIG_SCSI_ATA $CONFIG_PCI
-
 if [ "$CONFIG_PCI" = "y" ]; then
    dep_tristate '3ware Hardware ATA-RAID support' CONFIG_BLK_DEV_3W_XXXX_RAID $CONFIG_SCSI
 fi
fs/ext2/inode.c +0 -2
diff -urN 27p2.pac/fs/ext2/inode.c 27p2.acx/fs/ext2/inode.c
@@ -813,8 +813,6 @@
 		return;
 	if (ext2_inode_is_fast_symlink(inode))
 		return;
-	if (ext2_inode_is_fast_symlink(inode))
-		return;
 	if (IS_APPEND(inode) || IS_IMMUTABLE(inode))
 		return;
 
fs/ext3/inode.c +0 -2
diff -urN 27p2.pac/fs/ext3/inode.c 27p2.acx/fs/ext3/inode.c
@@ -1884,8 +1884,6 @@
 		return;
 	if (ext3_inode_is_fast_symlink(inode))
 		return;
-	if (ext3_inode_is_fast_symlink(inode))
-		return;
 	if (IS_APPEND(inode) || IS_IMMUTABLE(inode))
 		return;
 
drivers/scsi/pcmcia/Makefile +3 -3
diff -urN 27p2.pac/drivers/scsi/pcmcia/Makefile 27p2.acx/drivers/scsi/pcmcia/Makefile
@@ -22,9 +22,9 @@
 obj-$(CONFIG_PCMCIA_NINJA_SCSI)	+= nsp_cs.o
 
 list-multi	:= qlogic_cs.o fdomain_cs.o aha152x_cs.o
-aha152x_cs-objs	:= aha152x.o
-fdomain_cs-objs	:= fdomain.o
-qlogic_cs-objs	:= qlogicfas.o
+aha152x_cs-objs	:= aha152x_stub.o aha152x.o
+fdomain_cs-objs	:= fdomain_stub.o fdomain.o
+qlogic_cs-objs	:= qlogic_stub.o qlogicfas.o
 
 include $(TOPDIR)/Rules.make
 
drivers/char/drm/r128_state.c +2 -2
diff -urN 27p2.pac/drivers/char/drm/r128_state.c 27p2.acx/drivers/char/drm/r128_state.c
@@ -1025,7 +1025,7 @@
 
 	count = depth->n;
 
-	if ( count > 4096 || count <= 0 )
+	if ( count > 4096 || count <= 0)
 		return DRM_ERR(EMSGSIZE);
 
 	xbuf_size = count * sizeof(*x);
@@ -1191,7 +1191,7 @@
 
 	count = depth->n;
 	if ( count > 4096 || count <= 0)
-		return -EMSGSIZE;
+		return DRM_ERR(EMSGSIZE);
 
 	if ( count > dev_priv->depth_pitch ) {
 		count = dev_priv->depth_pitch;
drivers/char/drm/drmP.h +1 -72

87 lines not on this page · raw message

drivers/usb/storage/unusual_devs.h +4 -4
diff -urN 27p2.pac/drivers/usb/storage/unusual_devs.h 27p2.acx/drivers/usb/storage/unusual_devs.h
@@ -491,10 +491,10 @@
 		US_FL_IGNORE_SER ),
 
 UNUSUAL_DEV(  0x0781, 0x0100, 0x0100, 0x0100,
-                "Sandisk",
-                "ImageMate SDDR-12",
-                US_SC_SCSI, US_PR_CB, NULL,
-                US_FL_SINGLE_LUN ),
+		"Sandisk",
+		"ImageMate SDDR-12",
+		US_SC_SCSI, US_PR_CB, NULL,
+		US_FL_SINGLE_LUN ),
 
 #ifdef CONFIG_USB_STORAGE_SDDR09
 UNUSUAL_DEV(  0x0781, 0x0200, 0x0000, 0x9999, 
drivers/usb/Config.in +1 -1
diff -urN 27p2.pac/drivers/usb/Config.in 27p2.acx/drivers/usb/Config.in
@@ -28,7 +28,7 @@
          comment '  USB Bluetooth can only be used with disabled Bluetooth subsystem'
       fi
    fi
-   dep_tristate '  USB DFU support' CONFIG_USB_DFU $CONFIG_USB
+   dep_tristate '  USB Device Firmware Upgrade (DFU) support' CONFIG_USB_DFU $CONFIG_USB
    dep_tristate '  USB MIDI support' CONFIG_USB_MIDI $CONFIG_USB $CONFIG_SOUND
    if [ "$CONFIG_SCSI" = "n" ]; then
       comment '  SCSI support is needed for USB Storage'
drivers/usb/atmel/README +0 -9
diff -urN 27p2.pac/drivers/usb/atmel/README 27p2.acx/drivers/usb/atmel/README
@@ -181,12 +181,3 @@
 Oliver Kurth <[email protected]>, Mon,  6 Jan 2003 22:39:47 +0100
 updated by Joerg Albert, Thu, 1 May 2003 and later
 
-
-
-
-
-
-
-
-
-
arch/i386/kernel/i386_ksyms.c +2 -0
diff -urN 27p2.pac/arch/i386/kernel/i386_ksyms.c 27p2.acx/arch/i386/kernel/i386_ksyms.c
@@ -133,7 +133,9 @@
 EXPORT_SYMBOL(cpu_data);
 EXPORT_SYMBOL(kernel_flag_cacheline);
 EXPORT_SYMBOL(smp_num_cpus);
+EXPORT_SYMBOL(smp_num_siblings);
 EXPORT_SYMBOL(cpu_online_map);
+EXPORT_SYMBOL_GPL(cpu_sibling_map);
 EXPORT_SYMBOL_NOVERS(__write_lock_failed);
 EXPORT_SYMBOL_NOVERS(__read_lock_failed);
 
Documentation/Configure.help +2 -2
diff -urN 27p2.pac/Documentation/Configure.help 27p2.acx/Documentation/Configure.help
@@ -1336,8 +1336,8 @@
   not match, the driver attempts to do dynamic tuning of the chipset
   at boot-time for max speed.  Ultra33 BIOS 1.25 or newer is required
   for more than one card. This card may require that you say Y to
-  "Special UDMA Feature" to force UDMA mode for connected UDMA capable
-  disk drives.
+  "Special UDMA Feature" (or "Override-Enable UDMA for Promise Contr.")
+  to force UDMA mode for connected UDMA capable disk drives.
 
   If you say Y here, you need to say Y to "Use DMA by default when
   available" as well.