Skip to contentSkip to conversation

Getting i815 Framebuffer working?!

DISCUSSION James Lamanna 2 participants 2 messages May 6, 2004 – May 19, 2004

lore
Share & tools
lore
#0 lore raw

Using stock 2.6.5, I'm trying to get the Intel i810/5 framebuffer driver to work. So far I have had no success.

Any help would be appreciated, system data follows.

Please CC me for I am not subscribed.

-- James Lamanna

I'm using the following lilo.conf line:

append="video=i810fb:vram:2,xres:1024,yres:768,bpp:8,hsync1:30,\
        hsync2:55,vsync1:50,vsync2:85,accel,mtrr"

Relevant Statements from dmesg:
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: AGP aperture is 64M @ 0xe0000000
i810fb: probe of 0000:00:02.0 failed with error -22 ^^^^ Not promising... :)
NTFS driver 2.1.6 [Flags: R/O].
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones [drm] Initialized i810 1.4.0 20030605 on minor 0 [drm] Initialized i830 1.3.2 20021108 on minor 1

Relevant lspci output:

0000:00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics Controller] (rev 04) (prog-if 00 [VGA])
Subsystem: Intel Corp. 82815 CGC [Chipset Graphics Controller]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 0
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at e0000000 (32-bit, prefetchable)
        Region 1: Memory at e4100000 (32-bit, non-prefetchable)

[size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Relevant parts of .config:

# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_VESA is not set
# CONFIG_VIDEO_SELECT is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
CONFIG_FB_I810=y
CONFIG_FB_I810_GTF=y
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set

#1 lore raw
Quoted 6 lines · James Lamanna

Relevant Statements from dmesg:
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: AGP aperture is 64M @ 0xe0000000
i810fb: probe of 0000:00:02.0 failed with error -22 ^^^^ Not promising... :)

Make sure you set hsync1, hsync2 , vsync1 and vsync2 in your boot parameters.

For monitors that can do 1024x768@50Hz, the following should work.

hysnc1 = 30, hsync2 = 48, vsync1= 50 vsync2 = 85

Tony