SATA causing hard freeze on 2.6.6
Hi,
Since an IDE-->SATA converter was included with my motherboard, I decided to start playing with SATA.
The converter unit plugs into the IDE port of a hard disk, and you can then connect a SATA lead from that to a SATA port on the motherboard.
The hard disk I am using is a Seagate ST380011A.
The motherboard is an Abit NF7-S 2.0 (nforce2), which has the following SATA controller:
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) Silicon Image Serial ATARaid Controller [ CMD/Sil 3112/3112A ] (rev 02)
Under 2.6.6, the entire system freezes under disk activity. It starts booting ok, but then freezes, usually when loading modules. Booting with "init=/bin/bash" allows me to get to a console, but soon after I start using the disk, the entire system freezes. I also tried 2.6.6-mm2 with the same problems. Plugging back into IDE, and booting the same kernel works with no problems.
FWIW, my SATA experiences aren't much better with other kernels. When booting 2.4.25 from a CD, I can mount my SATA disk but I get lots of messages, such as:
hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
ide2(33,7):Removing [4428992 4467719 0x0 SD]..<4>hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
done
ide2(33,7):There were 1 uncompleted unlinks/truncates. Completed
hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
Booting 2.6.5 from a cd and mounting the drive gives the same errors. However, in both cases, reading and writing appears to be working (but I unmounted quickly both times incase the errors might be damaging the disk..)
Anything I could try?
Daniel
Quoted 21 lines · Daniel Drake
Hi,
Since an IDE-->SATA converter was included with my motherboard, I decided to start playing with SATA.
The converter unit plugs into the IDE port of a hard disk, and you can then connect a SATA lead from that to a SATA port on the motherboard.
The hard disk I am using is a Seagate ST380011A.
The motherboard is an Abit NF7-S 2.0 (nforce2), which has the following SATA controller:
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD Technology Inc) Silicon Image Serial ATARaid Controller [ CMD/Sil 3112/3112A ] (rev 02)Under 2.6.6, the entire system freezes under disk activity. It starts booting ok, but then freezes, usually when loading modules. Booting with "init=/bin/bash" allows me to get to a console, but soon after I start using the disk, the entire system freezes. I also tried 2.6.6-mm2 with the same problems. Plugging back into IDE, and booting the same kernel works with no problems.
FWIW, my SATA experiences aren't much better with other kernels. When booting 2.4.25 from a CD, I can mount my SATA disk but I get lots of messages, such as:
hde:sata_error=0x00000000, watchdog = 0,siimage_mmio_ide_dma_test_irq
ide2(33,7):Removing [4428992 44677190x0SD]..<4>hde:sata_error=0x00000000, watchdog = 0,siimage_mmio_ide_dma_test_irq
done
ide2(33,7):There were 1 uncompleted unlinks/truncates. Completed
hde:sata_error=0x00000000, watchdog = 0,siimage_mmio_ide_dma_test_irq
hde:sata_error=0x00000000, watchdog = 0,siimage_mmio_ide_dma_test_irq
Quoted 3 lines
Booting 2.6.5 from a cd and mounting the drive gives the same errors. However, in both cases, reading and writing appears to be working (but I unmounted quickly both times incase the errors might be damaging the disk..)
Anything I could try?
What is the behavior of libata?
CONFIG_SCSI_SATA, CONFIG_SCSI_SATA_SIL
Jeff
Quoted 3 lines · Jeff Garzik
What is the behavior of libata?
CONFIG_SCSI_SATA,CONFIG_SCSI_SATA_SIL
Ah, I had not made the link that those siimage_mmio_ide_dma_test_irq were being caused by a different driver. But I had been trying libata with the 2.6.6 kernel that I originally mentioned, and was getting the lockups.
Strangely, I started getting those lockups this morning while on IDE. I investigated the problem a bit further, and it turned out that a problematic SB Live was messing up the system (I had my suspicions on this card already). After removing that, I was able to boot up into IDE again. Just now, I plugged the SATA converter back in, and I'm now booted up on SATA with no problems at all.
Sorry for the noise :)
Daniel