Skip to contentSkip to conversation

dosemu-1.2.2

announce Stas Sergeev 3 participants 5 messages Jul 19, 2004 – Jul 20, 2004

lore
Share & tools
lore
#0 lore raw

Hello.

Quoted 2 lines · Ralph Alvy

Well, I'll wait until the next binary.
I'm not sure how to use that patch.

You can also upgrade from CVS. As a bonus, all the remaining problems with MaxThink (if there are still), should vanish. If you do neither, then the next binary is not guaranteed to have your problem eliminated.

#1 lore raw
Quoted 11 lines · Stas Sergeev

Hello.

Quoted 2 lines · Ralph Alvy

Well, I'll wait until the next binary.
I'm not sure how to use that patch.

You can also upgrade from CVS. As a bonus, all the remaining problems with MaxThink (if there are still), should vanish. If you do neither, then the next binary is not guaranteed to have your problem eliminated.

I understand. Well, MaxThink has worked well since 1.2.1. I'll check out CVS and see what I can do. Thanks.

#2 lore raw
In reply to Stas Sergeev
Quoted 11 lines · Stas Sergeev

Hello.

Quoted 2 lines · Ralph Alvy

Well, I'll wait until the next binary.
I'm not sure how to use that patch.

You can also upgrade from CVS. As a bonus, all the remaining problems with MaxThink (if there are still), should vanish. If you do neither, then the next binary is not guaranteed to have your problem eliminated.

I downloaded and successfully compiled and installed dosemu 1.3.1. I find the same problems with printing that I outlined before. I assume that 1.3.1 has the patch you talked about earlier.

#3 lore raw
Quoted 3 lines · Ralph Alvy

I downloaded and successfully compiled and installed dosemu 1.3.1. I find the same problems with printing that I outlined before. I assume that 1.3.1 has the patch you talked about earlier.

No, 1.3.1 was released on the same day as 1.2.2, it doesn't contain Stas' fix.

Since you have successfully compiled and installed 1.3.1, you've done most of the hard work already. What you'd need to do is:

save Stas' patch as lpt.diff in the dosemu source directory, and cd to it. Then type

patch -p0 < lpt.diff
make
su
make install

Bart

#4 lore raw
Quoted 20 lines · Bart Oldeman
Quoted 3 lines · Ralph Alvy

I downloaded and successfully compiled and installed dosemu 1.3.1. I find the same problems with printing that I outlined before. I assume that 1.3.1 has the patch you talked about earlier.

No, 1.3.1 was released on the same day as 1.2.2, it doesn't contain Stas' fix.

Since you have successfully compiled and installed 1.3.1, you've done most of the hard work already. What you'd need to do is:

save Stas' patch as lpt.diff in the dosemu source directory, and cd to it. Then type

patch -p0 < lpt.diff
make
su
make install

Quoted 6 lines

Bart

-
To unsubscribe from this list: send the line "unsubscribe linux-msdos" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Ah, okay. Well I followed the directions for patching and installing. What I I get now, when attempting to load the app in question, is this:

  ralvy@libranet:~/dosemu-1.3.1/bin$ ./xdosemu
  ERROR: cpu exception in dosemu code outside of VM86()!
  trapno: 0x0e  errorcode: 0x00000006  cr2: 0x053f3805
  eip: 0x40165512  esp: 0xbffff79c  eflags: 0x00210207
  cs: 0x0023  ds: 0x002b  es: 0x002b  ss: 0x002b
  Page fault: write instruction to linear address: 0x053f3805
  CPU was in user mode
  Exception was caused by non-available page