Skip to contentSkip to conversation

HP/Compaq (Winbond) SD/MMC reader supported

DISCUSSION Pierre Ossman 3 participants 10 messages Sep 3, 2004 – Sep 14, 2004

lore
Share & tools
lore
#0 lore raw

Since most people will search the LKML for drivers I'll post this little notice so people can find it.

The Winbond W83L519D SD/MMC card reader found in many of HP/Compaq's laptops (x1000, nx7000, nx7010, etc.) can now be used in Linux. The driver is still in its early stages and not ready for inclusion in the main kernel. But for those brave enough to fiddle around the driver can do both reads and writes. The only known problem is that it doesn't like some cards (they do not get past the init. so no risk of data loss).

The project web page is at:

http://projects.drzeus.cx/wbsd/

Please post your results on the development mailing list there.

Rgds
Pierre Ossman

#1 lore raw

Hi!

Quoted 10 lines

Since most people will search the LKML for drivers I'll post this little notice so people can find it.

The Winbond W83L519D SD/MMC card reader found in many of HP/Compaq's laptops (x1000, nx7000, nx7010, etc.) can now be used in Linux. The driver is still in its early stages and not ready for inclusion in the main kernel. But for those brave enough to fiddle around the driver can do both reads and writes. The only known problem is that it doesn't like some cards (they do not get past the init. so no risk of data loss).

Quoted 5 lines

The project web page is at:

http://projects.drzeus.cx/wbsd/

Please post your results on the development mailing list there.

Hmm, it does something here on my nx5000... It causes 2 "bad parity from KBD" errors and then freezes boot. But the chip is detected and I see

mmc0: W83L51xD id f00 at 0x248 irq 1 dma 0

message. (How do I guess right values for irq? I thought that interference with keyboard means it uses irq 1, but it is probably not the case, and default values did not work, too).

I'll try turning off ALSA because it actually freezes machine only after alsa is loaded.
Pavel

Signature · 2 lines
People were complaining that M$ turns users into beta-testers...
...jr ghea gurz vagb qrirybcref, naq gurl frrz gb yvxr vg gung jnl!
#2 lore raw
Quoted 6 lines · Pavel Machek

Hmm, it does something here on my nx5000... It causes 2 "bad parity from KBD" errors and then freezes boot. But the chip is detected and I see

Quoted 10 lines

mmc0: W83L51xD id f00 at 0x248 irq 1 dma 0

message. (How do I guess right values for irq? I thought that interference with keyboard means it uses irq 1, but it is probably not the case, and default values did not work, too).

I'll try turning off ALSA because it actually freezes machine only after alsa is loaded.

You seem to be running an old version of the driver. The ports for the driver are also often populated by SuperIO chip. The detection routine was a bit optimistic in the earlier versions so it started resetting the wrong hardware.

As of writing the latest version is 0.7 and a patch can be downloaded at:

http://projects.drzeus.cx/wbsd/download.php?get=files/wbsd-0.7.patch

Rgds
Pierre

#3 lore raw

Hi!

Quoted 14 lines
Quoted 4 lines

Hmm, it does something here on my nx5000... It causes 2 "bad parity from KBD" errors and then freezes boot. But the chip is detected and I see

Quoted 10 lines

mmc0: W83L51xD id f00 at 0x248 irq 1 dma 0

message. (How do I guess right values for irq? I thought that interference with keyboard means it uses irq 1, but it is probably not the case, and default values did not work, too).

I'll try turning off ALSA because it actually freezes machine only after alsa is loaded.

Quoted 8 lines

You seem to be running an old version of the driver. The ports for the driver are also often populated by SuperIO chip. The detection routine was a bit optimistic in the earlier versions so it started resetting the wrong hardware.

As of writing the latest version is 0.7 and a patch can be downloaded at:

http://projects.drzeus.cx/wbsd/download.php?get=files/wbsd-0.7.patch

Hmm, now I get "Unknown hardware (id f00) found at 2e". I'll try to investigate further.

Pavel

Signature · 2 lines
People were complaining that M$ turns users into beta-testers...
...jr ghea gurz vagb qrirybcref, naq gurl frrz gb yvxr vg gung jnl!
#4 lore raw
In reply to Pierre Ossman

Hi!

Quoted 14 lines
Quoted 4 lines

Hmm, it does something here on my nx5000... It causes 2 "bad parity from KBD" errors and then freezes boot. But the chip is detected and I see

Quoted 10 lines

mmc0: W83L51xD id f00 at 0x248 irq 1 dma 0

message. (How do I guess right values for irq? I thought that interference with keyboard means it uses irq 1, but it is probably not the case, and default values did not work, too).

I'll try turning off ALSA because it actually freezes machine only after alsa is loaded.

Quoted 8 lines

You seem to be running an old version of the driver. The ports for the driver are also often populated by SuperIO chip. The detection routine was a bit optimistic in the earlier versions so it started resetting the wrong hardware.

As of writing the latest version is 0.7 and a patch can be downloaded at:

http://projects.drzeus.cx/wbsd/download.php?get=files/wbsd-0.7.patch

Hmm, if I disable the check (and make id 0xf00 valid), it will freeze my machine during boot :-(. Where did you get documentation for this beast?

Pavel

Signature · 2 lines
People were complaining that M$ turns users into beta-testers...
...jr ghea gurz vagb qrirybcref, naq gurl frrz gb yvxr vg gung jnl!
#5 lore raw
Quoted 8 lines · Pavel Machek

Hmm, if I disable the check (and make id 0xf00 valid), it will freeze my machine during boot :-(. Where did you get documentation for this beast?

Is the 0xf00 id the only one you get? If it is a SuperIO chip then resetting it will probably cause all sorts of funky problems.
Do you know what SuperIO is used in the machine? And have you tried confirming that the card reader is indeed winbond? The easiest way to do that is to see if the Windows driver is wbsd.sys.

The documentation was given to me by one of Winbond's resellers (after a lot of begging and whining). It only includes documentation for one chip and the ID specified in it is not even the same as reported by the chip the spec is supposed to be for. Winbond is definitely not on my recommended vendors list.

Rgds
Pierre

#6 lore raw

Hi!

Quoted 5 lines
Quoted 4 lines

Hmm, if I disable the check (and make id 0xf00 valid), it will freeze my machine during boot :-(. Where did you get documentation for this beast?

Is the 0xf00 id the only one you get? If it is a SuperIO chip then

How can I (try to) get other id's? Yes, it seems to be stable across reboots.

Quoted 4 lines

resetting it will probably cause all sorts of funky problems. Do you know what SuperIO is used in the machine? And have you tried confirming that the card reader is indeed winbond? The easiest way to do that is to see if the Windows driver is wbsd.sys.

Stefan, could you take a look? I rm -rf'ed my copy of windows :-(.

SuperIO is behind ISA bridge so it can not be deduced from lspci? Or I may be completely off mark; there's Unknown mass storage controller:
Texas Instruments PCI7420 Flash Media Controller.... Hmm, that seems like flash.
Pavel

Signature · 2 lines
People were complaining that M$ turns users into beta-testers...
...jr ghea gurz vagb qrirybcref, naq gurl frrz gb yvxr vg gung jnl!
#7 lore raw
Quoted 3 lines · Pavel Machek

Hi!

Stefan, could you take a look? I rm -rf'ed my copy of windows :-(.

Me too, but fortunately i exchanged the nx5k with somebody else who hasn't :-)

Texas Instruments PCIxx20 Integrated FlashMedia controller
Driver: tifm.sys

Memory range: 90280000-90280fff
IRQ: 18

Stefan

#9 lore raw
In reply to Pavel Machek
Quoted 4 lines · Pavel Machek

Hi!

Quoted 8 lines
Quoted 3 lines

Is the 0xf00 id the only one you get? If it is a SuperIO chip then

How can I (try to) get other id's? Yes, it seems to be stable across reboots.

You don't. The driver will list all it finds, so if there's only one line then that's it.

Quoted 5 lines
Quoted 4 lines

resetting it will probably cause all sorts of funky problems.
Do you know what SuperIO is used in the machine? And have you tried confirming that the card reader is indeed winbond? The easiest way to do that is to see if the Windows driver is wbsd.sys.

Quoted 8 lines

Stefan, could you take a look? I rm -rf'ed my copy of windows :-(.

SuperIO is behind ISA bridge so it can not be deduced from lspci? Or I may be completely off mark; there's Unknown mass storage controller:
Texas Instruments PCI7420 Flash Media Controller.... Hmm, that seems like flash.

PCI7420 does indeed support SD/MMC so there's a high probability that this is the wrong driver for you. See if TI will release a complete spec. for the SD/MMC interface. Then you can start writing your own driver ;)

Rgds
Pierre

#8 lore raw
In reply to Stefan Seyfried

Hi!

Quoted 10 lines
Quoted 1 line

Stefan, could you take a look? I rm -rf'ed my copy of windows :-(.

Me too, but fortunately i exchanged the nx5k with somebody else who hasn't :-)

Texas Instruments PCIxx20 Integrated FlashMedia controller
Driver: tifm.sys

Memory range: 90280000-90280fff
IRQ: 18

Hmm, okay, this does not look compatible :-(. Sorry for the noise.

Pavel

Signature · 2 lines
People were complaining that M$ turns users into beta-testers...
...jr ghea gurz vagb qrirybcref, naq gurl frrz gb yvxr vg gung jnl!