Skip to contentSkip to conversation

Netconsole at startup

U-Boot-Users Robin Gilks 2 participants 4 messages Sep 22, 2004 – Sep 23, 2004

lore
Share & tools
lore
#0 lore raw

Greetings

Bit of a puzzle with netconsole operation.

If I undef CFG_CONSOLE_IS_IN_ENV, then I can boot to the serial console and manually switch it to nc and it works great. Problem with that is that on boot it just uses the first device that has the correct in/out properties - i.e. serial and ignores any env setting.

If I define CFG_CONSOLE_IS_IN_ENV, then the netconsole stuff refuses to run (i.e. it doesn't use serial but it doesn't use nc either!!) - even though when checking with the BDI2000 I can see that the correct nc devices have been set up in the dev structures. If I start up in serial and then try to switch to nc it just doesn't work - it continues to use serial.

Any clues from anyone? Should netconsole be able to run from bootup?

Signature · 17 lines
Robin Gilks
Senior Design Engineer          Phone: (+64)(3) 357 1569
Tait Electronics                Fax  :  (+64)(3) 359 4632
PO Box 1645 Christchurch        Email : robin.gilks at tait.co.nz
New Zealand

=======================================================================
This email, including any attachments, is only for the intended
addressee.  It is subject to copyright, is confidential and may be
the subject of legal or other privilege, none of which is waived or
lost by reason of this transmission.
If the receiver is not the intended addressee, please accept our
apologies, notify us by return, delete all copies and perform no
other act on the email.
Unfortunately, we cannot warrant that the email has not been
 altered or corrupted during transmission.
=======================================================================
#1 lore raw
Quoted 2 lines · In message <[email protected]> you wrote:

Bit of a puzzle with netconsole operation.

Which architecture, which board?

Quoted 4 lines

If I undef CFG_CONSOLE_IS_IN_ENV, then I can boot to the serial console and manually switch it to nc and it works great. Problem with that is that on boot it just uses the first device that has the correct in/out properties - i.e. serial and ignores any env setting.

What exactly is the problem with this? It's what I would expect... If you want to automatically switch to NC as soon as it becomes available you can always do this using some CONFIG_PREBOOT settings.

Quoted 2 lines

If I define CFG_CONSOLE_IS_IN_ENV, then the netconsole stuff refuses to run (i.e. it doesn't use serial but it doesn't use nc either!!) - even

What does your overwrite_console() look like?

And what exactly are you trying to do here? What does your environment settings look like?

Quoted 1 line

Any clues from anyone? Should netconsole be able to run from bootup?

What do you mean by "bootup"? NC will or course only work after the main intitialization sequence has been completed, i. e. after relocation to RAM, and after ethernet and devices initialization.

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
The software required `Windows 95 or better', so I installed Linux.
#2 lore raw
Quoted 6 lines · Wolfgang Denk
Quoted 1 line · In message <[email protected]> you wrote:

Bit of a puzzle with netconsole operation.

Which architecture, which board?

I thought the whole point of the core code of u-boot was that it was architecture independent - I'm obviously wrong there...Its a custom mpc859 board as it happens.

Quoted 9 lines
Quoted 4 lines

If I undef CFG_CONSOLE_IS_IN_ENV, then I can boot to the serial console and manually switch it to nc and it works great. Problem with that is that on boot it just uses the first device that has the correct in/out properties - i.e. serial and ignores any env setting.

What exactly is the problem with this? It's what I would expect... If you want to automatically switch to NC as soon as it becomes available you can always do this using some CONFIG_PREBOOT settings.

I was relating the results of the two possible states of the compile time #define

Quoted 6 lines
Quoted 3 lines

If I define CFG_CONSOLE_IS_IN_ENV, then the netconsole stuff refuses to run (i.e. it doesn't use serial but it doesn't use nc either!!) - even

What does your overwrite_console() look like?

Why should I even have it defined - if its supposed to read the device from the environment then it seems reasonable that it does so at a point when initialisation is complete and its able to make use of it.

Quoted 2 lines

And what exactly are you trying to do here? What does your environment settings look like?

I have stdin=nc, stdout=nc, stderr=nc, ncip=172.25.x.x - all values that work fine when used interactively!!

Quoted 6 lines
Quoted 1 line

Any clues from anyone? Should netconsole be able to run from bootup?

What do you mean by "bootup"? NC will or course only work after the main intitialization sequence has been completed, i. e. after relocation to RAM, and after ethernet and devices initialization.

I can see the assignment in console_init_r() occuring OK for the values in the environment, its just that (presumably) the init order is not correct somewhere so it doesn't actually work!!

The whole point is now moot since your suggestion of CONFIG_PREBOOT solves the problem - its a bit of a cackhanded way of doing it which is what threw me for a while there!

One suggestion for the shell script to drive it from Linux - add a '-icrnl' to the stty line to stop 'cr' characters getting translated - works wonders at confounding the password patch from Pantelis Antoniou :-))

Signature · 17 lines
Robin Gilks
Senior Design Engineer          Phone: (+64)(3) 357 1569
Tait Electronics                Fax  :  (+64)(3) 359 4632
PO Box 1645 Christchurch        Email : robin.gilks at tait.co.nz
New Zealand

=======================================================================
This email, including any attachments, is only for the intended
addressee.  It is subject to copyright, is confidential and may be
the subject of legal or other privilege, none of which is waived or
lost by reason of this transmission.
If the receiver is not the intended addressee, please accept our
apologies, notify us by return, delete all copies and perform no
other act on the email.
Unfortunately, we cannot warrant that the email has not been
 altered or corrupted during transmission.
=======================================================================
#3 lore raw
Quoted 6 lines · In message <[email protected]> you wrote:
Quoted 2 lines

Which architecture, which board?

I thought the whole point of the core code of u-boot was that it was architecture independent - I'm obviously wrong there...Its a custom mpc859 board as it happens.

It's the intention to be HW independent, but obviously this may need support on the driver side, too.

MPC8xx should work, though.

Quoted 8 lines
Quoted 4 lines
Quoted 2 lines

If I define CFG_CONSOLE_IS_IN_ENV, then the netconsole stuff refuses to run (i.e. it doesn't use serial but it doesn't use nc either!!) - even

What does your overwrite_console() look like?

Why should I even have it defined - if its supposed to read the device from the environment then it seems reasonable that it does so at a point when initialisation is complete and its able to make use of it.

It may be reasonable, but I'm also pretty sure that it was never tested when we implemented the NC stuff.

Quoted 5 lines
Quoted 2 lines

And what exactly are you trying to do here? What does your environment settings look like?

I have stdin=nc, stdout=nc, stderr=nc, ncip=172.25.x.x - all values that work fine when used interactively!!

In interactive mode these settings take effect MUCH later.

Quoted 3 lines

I can see the assignment in console_init_r() occuring OK for the values in the environment, its just that (presumably) the init order is not correct somewhere so it doesn't actually work!!

Probably. I guess you will have to debug & fix this.

Quoted 3 lines

One suggestion for the shell script to drive it from Linux - add a '-icrnl' to the stty line to stop 'cr' characters getting translated - works wonders at confounding the password patch from Pantelis Antoniou :-))

I hate boot loaders which have passwords. They might deny me access to the machine ...

Best regards,

Wolfgang Denk

Signature · 6 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
That Microsoft, the Trabant of the operating  system  world,  may  be
glancing  over the Berlin Wall at the Audis and BMWs and Mercedes. In
their own universe Trabants and Ladas were mainstream too...
                                                   -- Evan Leibovitch