Skip to contentSkip to conversation

HELP: unable to use I-MATE SP3 as USB (HTC) gprs modem

DISCUSSION Luigi Genoni 1 participant 1 message Sep 1, 2005 3 messages not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#3 lore raw

lsusb -v gives:

Bus 001 Device 003: ID 0bb4:00cf High Tech Computer Corp. Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00

  bDeviceClass            2 Communications
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0bb4 High Tech Computer Corp.
  idProduct          0x00cf
  bcdDevice            0.90
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      1

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 255
bInterfaceProtocol 255
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 80

As I said, cdc-acm is not satisfied with this kind of device. I do not know how to make it work. Also usbserial didn't work. How could I make them work?

Please, note that the same command, used when the gprs modem is disabled (so i am using ipaq module in this case), gives:

Bus 001 Device 005: ID 0bb4:0a51 High Tech Computer Corp. SPV C400 / T-Mobile SDA GSM/GPRS Pocket PC
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00

  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass       255 Vendor Specific Subclass
  bDeviceProtocol       255 Vendor Specific Protocol
  bMaxPacketSize0        64
  idVendor           0x0bb4 High Tech Computer Corp.
  idProduct          0x0a51 SPV C400 / T-Mobile SDA GSM/GPRS Pocket PC
  bcdDevice            0.00
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      3

Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 2
iConfiguration 0
bmAttributes 0x80
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 3
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0

which is, for what I understand (not to mutch to say the truth) really different.

Obviously I will be happy to make all the test you will ask me.

Luigi Genoni

Quoted 44 lines · Vojtech Pavlik
Quoted 27 lines · Oliver Neukum
Quoted 27 lines

I should use as an USB gprs modem.

Since it is possible to configure it to be a (HTC) modem, using it's menu, when I enable it to act as a modem on the usb port the content of /proc/bus/usb/devices who refers to the phone changes to: I

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 37 Spd=12  MxCh= 0
D:  Ver= 1.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0bb4 ProdID=00cf Rev= 0.90
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=02(comm.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  16 Ivl=80ms

The hotplug does not work anymore using the ipaq driver (as I exspected), and the device is not attacched to ttyUSB0.

I read Cls=02(comm.). I suppose there should be a way to use something like cdc-acm driver. Unfortunatelly this driver does not seem to like my phone.
All I get is a sad:

usb 1-1: new full speed USB device using uhci_hcd and address 39

Quoted 7 lines
Quoted 2 lines

Is there a way to solve this problem and to use I-mate SP3 smartphone as gprs modem for linux or should I surrender?

Is there just one interface?
If so, looks like somebody tried to be clever and collapsed the control and the data interfaces of the acm specification. The ACM driver can be hacked to support that.

That is, if the ACM command set actually works, otherwise it's a job for usb-serial.

Quoted 5 lines

Can you confirm that there's just one interface and no extra descriptors? (lsusb -v)

Regards
Oliver