2.6.9 broke Cirque HID Touchpad support
I just noticed that 2.6.9 seems to have broken support for my Cirque USB touchpad. With 2.6.8-gentoo-r4 it works fine with essentially the same kernel config:
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 usb 2-1: new low speed USB device using address 3
usb 2-1: skipped 1 descriptor after interface
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
usb 2-1: Product: USB GlidePoint
usb 2-1: Manufacturer: Cirque Corporation
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: USB HID v1.00 Mouse [Cirque Corporation USB GlidePoint] on usb-0000:00:10.0-1
With 2.6.9-gentoo-r1 I get the following USB debug messages:
usb 2-1: new low speed USB device using address 5uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
[000001003f891300] link (3f891242) element (3f890060)
0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0) 1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000) uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
[000001003f891300] link (3f891242) element (3f890060)
0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0) 1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000) usb 2-1: device not accepting address 5, error -71uhci_hcd 0000:00:10.0: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
usb 2-1: new low speed USB device using address 6uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
[000001003f891300] link (3f891242) element (3f890060)
0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0) 1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000) uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
[000001003f891300] link (3f891242) element (3f890060)
0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d8500) 1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000) usb 2-1: device not accepting address 6, error -71
Here are relevant config vars:CONFIG_X86_64=yCONFIG_64BIT=yCONFIG_X86=yCONFIG_MMU=yCONFIG_RWSEM_GENERIC_SPINLOCK=yCONFIG_X86_TSC=yCONFIG_X86_GOOD_APIC=yCONFIG_X86_IO_APIC=yCONFIG_X86_LOCAL_APIC=yCONFIG_MTRR=yCONFIG_SMP=yCONFIG_PREEMPT=y
CONFIG_INPUT=y
CONFIG_INPUT_EVDEV=yCONFIG_INPUT_MOUSE=y
#
# Userland interfaces
#CONFIG_INPUT_MOUSEDEV=yCONFIG_INPUT_MOUSEDEV_PSAUX=yCONFIG_INPUT_MOUSEDEV_SCREEN_X=1024CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768CONFIG_INPUT_JOYDEV=y
CONFIG_USB=yCONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#CONFIG_USB_EHCI_HCD=yCONFIG_USB_UHCI_HCD=y
CONFIG_USB_HID=yCONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not setCONFIG_USB_HIDDEV=y
Signature · 1 line
James Lamanna