Syscontrol activation = problem on boot
Hi !
This is my first post on this list, and I could need some help to know if I made something wrong or if it is a bug ....
I compiled a new kernel and activated following option
General Setup > Sysctrl Support
in order to be able to use hotplug , udev .....
But on boot I become following error message concerning my second harddisk (/dev/hdb) which is dedicated to my old Win2k system :
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
Quoted 4 lines
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: error=0x04 { DriveStatusError }
Nov 12 19:15:13 ishwara kernel: ide: failed opcode was: unknown
Nov 12 19:15:13 ishwara kernel: end_request: I/O error, dev hdb, sector 78172098
Nov 12 19:15:13 ishwara kernel: Buffer I/O error on device hdb5, logical block 61785735it can last two or three minutes and then I have accsess to my Gnome Desktop.
This arrives on a 2.6.7 or 2.6.9 kernel if I try to activate Sysctrl in General Setup, if I deactivate it, I have not such error messages ....
To resume it : Is it a bug ? Or did I make something wrong ? Forget some options ?
System : Pentium 4 2,8Ghz
Motherboard Asus P4P 800
Chipset I865PE
and two Maxtor ATA-Harddisks
Thanks for helping
mahahshakti89
Please Cc your answers to [email protected]
I have similar errors, but they don't give me any problems (except that it looks bad).
Can you mount and use the harddisk?
Regards,
Norbert
Quoted 56 lines · On Sunday 14 November 2004 18:35, mahashakti89 wrote:
Hi !
This is my first post on this list, and I could need some help to know if I made something wrong or if it is a bug ....
I compiled a new kernel and activated following option
General Setup > Sysctrl Support
in order to be able to use hotplug , udev .....
But on boot I become following error message concerning my second harddisk (
/dev/hdb) which is dedicated to my old Win2k system :Nov 12 19:15:13 ishwara kernel: hdb: read_intr: status=0x59 {DriveReady SeekComplete DataRequest Error }
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: error=0x04 {DriveStatusError }
Quoted 2 lines
Nov 12 19:15:13 ishwara kernel: ide: failed opcode was: unknown Nov 12 19:15:13 ishwara kernel: end_request: I/O error, dev hdb,sector 78172098
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: Buffer I/O error on device hdb5,logical block 61785735
it can last two or three minutes and then I have accsess to my Gnome Desktop.
This arrives on a 2.6.7 or 2.6.9 kernel if I try to activate Sysctrl in General Setup, if I deactivate it, I have not such error messages ....
To resume it : Is it a bug ? Or did I make something wrong ? Forget some options ?
System : Pentium 4 2,8Ghz
Motherboard Asus P4P 800
Chipset I865PE
and two Maxtor ATA-HarddisksThanks for helping
mahahshakti89
Please Cc your answers to [email protected]
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 9 lines
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: status=0x59 {DriveReady SeekComplete DataRequest Error }
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: error=0x04 {DriveStatusError }
Quoted 2 lines
Nov 12 19:15:13 ishwara kernel: ide: failed opcode was: unknown Nov 12 19:15:13 ishwara kernel: end_request: I/O error, dev hdb,sector 78172098
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: Buffer I/O error on device hdb5,logical block 61785735
Looks like an old harddisk that does not understand an IDE command.
Quoted 2 lines
it can last two or three minutes and then I have accsess to my Gnome Desktop.
Do you think that's normal? I can come up in less than 60 secs. (80x25), so I presume boting X does not take much more time than 3 minutes. What do you mean by "last"? Does the error message stay there and the box is like, idle? No other stuff scrolling through?
Quoted 2 lines
This arrives on a 2.6.7 or 2.6.9 kernel if I try to activate Sysctrl in General Setup, if I deactivate it, I have not such error messages ....
Well, error message there or not -- I suspect it to be the hard disk. Take it out (i.e. remove IDE cable) and reboot Linux.
If it takes the same amount of time to bootup, the hard disk is probably fine. Ignore the warnings then.
Quoted 3 lines
and two Maxtor ATA-Harddisks
Jan Engelhardt
Signature · 2 lines
Gesellschaft für Wissenschaftliche Datenverarbeitung Am Fassberg, 37077 Göttingen, www.gwdg.de
Quoted 2 lines · Norbert van Nobelen
I have similar errors, but they don't give me any problems (except that it looks bad). Can you mount and use the harddisk?
Yes !
No problems
Quoted 43 lines
Regards,
Norbert
Quoted 35 lines · On Sunday 14 November 2004 18:35, mahashakti89 wrote:
But on boot I become following error message concerning my second harddisk (
/dev/hdb) which is dedicated to my old Win2k system :Nov 12 19:15:13 ishwara kernel: hdb: read_intr: status=0x59 {DriveReady SeekComplete DataRequest Error }
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: error=0x04 {DriveStatusError }
Quoted 2 lines
Nov 12 19:15:13 ishwara kernel: ide: failed opcode was: unknown Nov 12 19:15:13 ishwara kernel: end_request: I/O error, dev hdb,sector 78172098
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: Buffer I/O error on device hdb5,logical block 61785735
it can last two or three minutes and then I have accsess to my Gnome Desktop.
This arrives on a 2.6.7 or 2.6.9 kernel if I try to activate Sysctrl in General Setup, if I deactivate it, I have not such error messages ....
To resume it : Is it a bug ? Or did I make something wrong ? Forget some options ?
System : Pentium 4 2,8Ghz
Motherboard Asus P4P 800
Chipset I865PE
and two Maxtor ATA-Harddisks
Quoted 20 lines · Jan Engelhardt
Quoted 7 lines
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: status=0x59 {DriveReady SeekComplete DataRequest Error }
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: hdb: read_intr: error=0x04 {DriveStatusError }
Quoted 8 lines
Quoted 2 lines
Nov 12 19:15:13 ishwara kernel: ide: failed opcode was: unknown Nov 12 19:15:13 ishwara kernel: end_request: I/O error, dev hdb,sector 78172098
Quoted 1 line
Nov 12 19:15:13 ishwara kernel: Buffer I/O error on device hdb5,logical block 61785735
Looks like an old harddisk that does not understand an IDE command.
Quoted 7 lines
Quoted 2 lines
it can last two or three minutes and then I have accsess to my Gnome Desktop.
Do you think that's normal? I can come up in less than 60 secs. (80x25), so I presume boting X does not take much more time than 3 minutes. What do you mean by "last"?
It lasts for two or three minutes -sorry my english ... Does the error message stay there and the box is
Quoted 1 line
like, idle? No other stuff scrolling through?
Its scrolling the same message for two minutes and what I have posted is the end of the message, then I am logging into X.