Skip to contentSkip to conversation

Broken usb2 mass-storage?

2.6.10-rc2-mm3 Christian Axelsson 3 participants 3 messages Nov 29, 2004 – Nov 30, 2004

lore
Share & tools
lore
#0 lore raw

Hi!

Im trying to attach a usb2 200gb drive to my laptop that is runnig 2.6.10-rc2-mm3. Upon connect I get this in dmesg:

usb 1-2: new high speed USB device using ehci_hcd and address 4 scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: Maxtor 6 Model: Y200P0 Rev: YAR4
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0

Then I try to access the disk (via fdisk or mount anything) and I get the following in dmesg:

usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110

Then it stalls a while and this shows up:

scsi: Device offlined - not ready after error recovery: host 0
channel 0 id 0 lun 0
usb 1-2: USB disconnect, address 4
scsi0 (0:0): rejecting I/O to offline device
scsi0 (0:0): rejecting I/O to offline device
usb-storage: device scan complete
usb 1-2: new high speed USB device using ehci_hcd and address 5 usb 1-2: khubd timed out on ep0in
usb 1-2: device descriptor read/64, error -110

And repeats this.. I think you get the point ;)
The process trying to access the disk hangs.
Note: the drive works flawless under windows and has worked fine under linux during various stages of the 2.5 and early 2.6 kernels :)

Signature · 2 lines
Regards,
Christian
#1 lore raw
Quoted 4 lines · Christian Axelsson

Hi!

Im trying to attach a usb2 200gb drive to my laptop that is runnig 2.6.10-rc2-mm3. Upon connect I get this in dmesg:

Hm, so 2.6.10-rc2 works for you?

Quoted 11 lines

usb 1-2: new high speed USB device using ehci_hcd and address 4 scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: Maxtor 6 Model: Y200P0 Rev: YAR4
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0

That looks good.

Quoted 5 lines

Then I try to access the disk (via fdisk or mount anything) and I get the following in dmesg:

usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in

Ick, not good.

I'll leave the rest of the logs below, for the linux-usb-devel people to potentually help out.

Oh, have you tried the ub driver instead? Does that work for this device?

Quoted 19 lines

usb 1-2: device descriptor read/64, error -110
usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110

Then it stalls a while and this shows up:

scsi: Device offlined - not ready after error recovery: host 0
channel 0 id 0 lun 0
usb 1-2: USB disconnect, address 4
scsi0 (0:0): rejecting I/O to offline device
scsi0 (0:0): rejecting I/O to offline device
usb-storage: device scan complete
usb 1-2: new high speed USB device using ehci_hcd and address 5 usb 1-2: khubd timed out on ep0in
usb 1-2: device descriptor read/64, error -110

Quoted 5 lines

And repeats this.. I think you get the point ;)
The process trying to access the disk hangs.
Note: the drive works flawless under windows and has worked fine under linux during various stages of the 2.5 and early 2.6 kernels :)

thanks,

greg k-h

#2 lore raw
Quoted 7 lines · Greg KH
Quoted 5 lines

Then I try to access the disk (via fdisk or mount anything) and I get the following in dmesg:

usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in

Ick, not good.

Has this device always needed a reset? The interesting bits of the log are probably the ones immediatelly preceding the decision to reset it. Two possibilities come to mind:
something broke the reset logic (the device is clearly not working right after the reset) ... or something changed to make the device go bonkers _before_ the reset, which seems a bit more likely with my current lack-of-facts. (Especially if rc2 works and mm3 doesn't.)

- Dave

Quoted 26 lines

...

Quoted 24 lines

usb 1-2: device descriptor read/64, error -110
usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110
usb 1-2: reset high speed USB device using ehci_hcd and address 4 usb 1-2: scsi_eh_0 timed out on ep0in
usb 1-2: device descriptor read/64, error -110

Then it stalls a while and this shows up:

scsi: Device offlined - not ready after error recovery: host 0
channel 0 id 0 lun 0
usb 1-2: USB disconnect, address 4
scsi0 (0:0): rejecting I/O to offline device
scsi0 (0:0): rejecting I/O to offline device
usb-storage: device scan complete
usb 1-2: new high speed USB device using ehci_hcd and address 5 usb 1-2: khubd timed out on ep0in
usb 1-2: device descriptor read/64, error -110

And repeats this.. I think you get the point ;)
The process trying to access the disk hangs.
Note: the drive works flawless under windows and has worked fine under linux during various stages of the 2.5 and early 2.6 kernels :)