Skip to contentSkip to conversation

Simple case here!

LARTC Amit Vyas 2 participants 3 messages Dec 28, 2004 – Jan 2, 2005

lore
Share & tools
lore

Amit Vyas

author
#0 lore raw

Hi All,

I want to setup a machine to connect to internet at a limited rate of 64 kbps.
That machine is connected to a switch. so my LAN and Internet both comes from the same eth0.
How can I limit only the internet access from this machine to 64kbps and still using 100mbps for LAN

I am trying to implement this Please guide me If i am wrong. I mark all the packets going out to LAN.
Then I can setup a root qdisc to classify packets based on that mark. If match then I can setup a class to accept those setup a fifo for those packets. but if the packets are not for the LAN then i can pass them to other class which is tbf shaping at rate 64kbps.

Am i right on these lines.
This is the setup

+------------+   eth0        +-----------+   internet
| machine   |---------------|   Switch  |-------------
+------------+                  +-----------+

trying to get some thing like this

                         root qdisc  (CBQ or something)
                            /     \
                          /         \
                        /             \
                      /                 \
                class              class
Internal LAN Pcakets        Any other unclassified Packets
                  |                      |
                  |                      |
               FIFO             TBF (rate 64kbps)

Please Help me out with marking the packets and to classify them. Just started off with Traffic Shaping. gigles...... : )

It is alos possible to alternatively to mark internet traffic as it would be less in comparison to LAN and thus processor friendly.

Amit Vyas

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#1 lore raw

I tried This for the following setup but it doesn't seems to be working Please suggest.

//making a root cbq
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 100Mbit allot 1514 cell 8 avpkt 1000 mpu 64

//making one class under root with limiting 64kbps
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 1Mbit rate 64Kbit allot 1514 cell 8 avpkt 1000 mpu 64 isolated

//Making other class which can take all the packets for the LAN and procced with them at spped available.
tc class add dev eth0 parent 1:0 classid 1:2 cbq bandwidth 99Mbit rate 100kbit weight 9kbit allot 1514 cell 8

//filtering the packets so that they can be classified for class 1:2 tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst 192.168.3.0/32 classid 1:2
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst 192.168.2.0/32 classid 1:2

Quoted 49 lines · Amit Vyas

Hi All,

I want to setup a machine to connect to internet at a limited rate of 64 kbps.
That machine is connected to a switch. so my LAN and Internet both comes from the same eth0.
How can I limit only the internet access from this machine to 64kbps and still using 100mbps for LAN

I am trying to implement this Please guide me If i am wrong. I mark all the packets going out to LAN.
Then I can setup a root qdisc to classify packets based on that mark. If match then I can setup a class to accept those setup a fifo for those packets. but if the packets are not for the LAN then i can pass them to other class which is tbf shaping at rate 64kbps.

Am i right on these lines.
This is the setup

+------------+   eth0        +-----------+   internet
| machine   |---------------|   Switch  |-------------
+------------+                  +-----------+

trying to get some thing like this

                        root qdisc  (CBQ or something)
                           /     \
                         /         \
                       /             \
                     /                 \
               class              class
Internal LAN Pcakets        Any other unclassified Packets
                 |                      |
                 |                      |
              FIFO             TBF (rate 64kbps)

Please Help me out with marking the packets and to classify them. Just started off with Traffic Shaping. gigles...... : )

It is alos possible to alternatively to mark internet traffic as it would be less in comparison to LAN and thus processor friendly.

Amit Vyas

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Amit Vyas
Quoted 37 lines · Amit Vyas

Hi All,

I want to setup a machine to connect to internet at a limited rate of 64 kbps.
That machine is connected to a switch. so my LAN and Internet both comes from the same eth0.
How can I limit only the internet access from this machine to 64kbps and still using 100mbps for LAN

I am trying to implement this Please guide me If i am wrong. I mark all the packets going out to LAN.
Then I can setup a root qdisc to classify packets based on that mark. If match then I can setup a class to accept those setup a fifo for those packets. but if the packets are not for the LAN then i can pass them to other class which is tbf shaping at rate 64kbps.

Am i right on these lines.
This is the setup

+------------+   eth0        +-----------+   internet
| machine   |---------------|   Switch  |-------------
+------------+                  +-----------+

trying to get some thing like this

                        root qdisc  (CBQ or something)
                           /     \
                         /         \
                       /             \
                     /                 \
               class              class
Internal LAN Pcakets        Any other unclassified Packets
                 |                      |
                 |                      |
              FIFO             TBF (rate 64kbps)
Quoted 7 lines

Please Help me out with marking the packets and to classify them. Just started off with Traffic Shaping. gigles...... : )

It is alos possible to alternatively to mark internet traffic as it would be less in comparison to LAN and thus processor friendly.

Amit Vyas

I would use netfilter + HTB something like -

$TC qdisc add dev eth0 root handle 1:0 htb default 0 $TC class add dev eth0 parent 1:0 classid 1:1 htb rate 64kbit

$TC filter add dev eth0 parent 1:0 protocol ip handle 1 fw flowid 1:1

$IPTABLES -t mangle -A POSTROUTING -o eth0 --dst ! 192.168.0.0/24 -j MARK --set-mark 1

Depending on what the PC does it may be nicer to priorotise empty acks / udp headed for the internet over bulk traffic.

Andy.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/