cpu throttling powernow-k8 and acpi in kernel
Hi guys!
I have an acer aspire 1501 lmi with amd64 @3000+. i am running a gentoo 64bit dist with vanilla 2.6.10 kernel on it.
i encounter some problems with the speed throttling of the cpu. this kind of cpu has 3 steps which a gouvernor can reach, 1800, 1600 and 800Mhz. i am using the ondemand gouvernor. so far this works quite good, ondemand puts it at 800 until i do something. as it should be. i have also CONFIG_ACPI_PROCESSOR=y and CONFIG_ACPI_THERMAL=y enabled. when acpi thinks the temperature is too high (95° for cpu) it throttles the cpu down to 800Mhz, no care what ondemand tells it. okay, why not, is a good protection for overheating. but i don't think the cpu has 95°, i have run the laptop much hotter once, and there was no downthrottling. it cannot be that i am not able to compile a simple package without getting a critical temperature. i am watching the temps in gkrellm and this leads me to the thing that there is something wrong with it cause it jumps a bit when the temps are getting higher and one thing more, when the laptop is doing nothing, e.g. over night, screen is off, cpu is at 800 the temp is still at about 55° and more, how can that be? but i cannot disable the two acpi-options mentionend above. at first the cpu runs at 800, no problem, fan is almost off. but when i start e.g. a compilation first the fan starts spinning up a bit, the cpu goes to 1800mhz but after a while the fan gives all the speed it is able to, much noise, and after one or 2 minutes the laptop switches off immediate.
Has anyone any idea on this? a tipp or something? i hope i did not forget any information.
Regards and keep on the good work
Georg Schild
Quoted 4 lines · Georg Schild
I have an acer aspire 1501 lmi with amd64 @3000+. i am running a gentoo 64bit dist with vanilla 2.6.10 kernel on it.
i encounter some problems with the speed throttling of the cpu. this kind of
skipped...
Try writing to [email protected]. I had a CPU-throttling problem, when the CPU got throttled down without really getting hot - I just had wrongly configured /etc/sensors.conf. Might be your problem too?
HTH
Guennadi
---
Guennadi Liakhovetski
Quoted 4 lines
skipped...
Try writing to [email protected]. I had a CPU-throttling problem, when the CPU got throttled down without really getting hot - I just had wrongly configured
/etc/sensors.conf. Might be your problem too?
Would be happy if it were the sensors but i am not using them, a least not the ones lm-sensors can use. My temperature is shown via ACPI Thermal zone of the processor driver. Afaik ACPI does also regulate the fan-speed so it doesn't work proper without acpi-processor driver as mentionend in the first post. so i don't think that the different sensors in i2c have to do something with it. But thanks for response, good to know that others have similar problems, even if they are not the same ;) Anyone else an idea how to tell acpi that it has perhaps wrong values?. I remember that when i first used this laptop with linux the fan went off after some time but now the fan doesn't go off, at least i don't recognize it. this is just because acpi has too high temps and lets the fan cool down the cpu because of that (at least acpi thinks so ;)). Thanks for every help
Georg Schild
Quoted 5 lines · Georg Schild
Hi guys!
I have an acer aspire 1501 lmi with amd64 @3000+. i am running a gentoo 64bit dist with vanilla 2.6.10 kernel on it.
i encounter some problems with the speed throttling of the cpu. this
Just for telling you what has caused my cpu to spin down all the time. it looks like the acpi was right to tell me that the laptop got very hot, i just didn't notice cause the air out of the laptop wasn't hot, this was because some dust was somewhere in the fan/heatpipe which caused the machine to overheat. now i know a bit more, acpi was right in throttling the cpu, thank god for acpi ;)
cya and keep on the good work
Georg Schild
Hi!
Quoted 16 lines
I have an acer aspire 1501 lmi with amd64 @3000+. i am running a gentoo 64bit dist with vanilla 2.6.10 kernel on it.
i encounter some problems with the speed throttling of the cpu. this kind of cpu has 3 steps which a gouvernor can reach, 1800, 1600 and 800Mhz. i am using the ondemand gouvernor. so far this works quite good, ondemand puts it at 800 until i do something. as it should be. i have also
CONFIG_ACPI_PROCESSOR=yandCONFIG_ACPI_THERMAL=yenabled. when acpi thinks the temperature is too high (95 for cpu) it throttles the cpu down to 800Mhz, no care what ondemand tells it. okay, why not, is a good protection for overheating. but i don't think the cpu has 95, i have run the laptop much hotter once, and there was no downthrottling. it cannot be that i am not able to compile a simple package without getting a critical temperature. i am watching the temps in gkrellm and this leads me to the thing that there is something wrong with it cause it jumps a bit when the temps
Quoted 9 lines
are getting higher and one thing more, when the laptop is doing nothing, e.g. over night, screen is off, cpu is at 800 the temp is still at about 55 and more, how can that be? but i cannot disable the two acpi-options mentionend above. at first the cpu runs at 800, no problem, fan is almost off. but when i start e.g. a compilation first the fan starts spinning up a bit, the cpu goes to 1800mhz but after a while the fan gives all the speed it is able to, much noise, and after one or 2 minutes the laptop switches off immediate.
It seems your machine indeed is overheating. Modern cpus produce a lot of heat.
55C idle temperature seems okay. Open machine and attach your own temperature sensor to cpu to verify...
Pavel
Signature · 1 line
64 bytes from 195.113.31.123: icmp_seq=28 ttl=51 time=448769.1 ms
Quoted 6 lines
It seems your machine indeed is overheating. Modern cpus produce a lot of heat.
55C idle temperature seems okay. Open machine and attach your own temperature sensor to cpu to verify...
Pavel
I have found this out on my own now, indeed the cpu was overheating, there was dust or something in the fans way outside, when i blew into the laptop the fan got much more silent and the temp went down. works now quite good ;)