mpc8560ads PCI bus
Has anyone else tried to get the PCI bus working on the mpc8560ads board at 2.6.11? The card enumerates, but the I/O resource regions aren't getting set up.
-bash-2.05b# lspci -vv
00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
PCI0680 Ultra ATA-133 Host Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 100
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Greg Weeks
Hello, Greg,
I am working on an mpc8540_ads-like board and recently, I ran into data
corruption problems with a Silicon Motion SM501 (Rev AA) PCI graphics card. From my current point of view it seems that Kernel 2.6.11 PCI works well. I am about to check the hardware and signal integrity.
BTW: I am working with a Promise Ultra-TX133 IDE controller (PDC20269) which is fine with 66MHz PCICLK.
Greets,
Clemens
Quoted 27 lines
Has anyone else tried to get the PCI bus working on the mpc8560ads board at 2.6.11? The card enumerates, but the I/O resource regions aren't getting set up.
-bash-2.05b# lspci -vv
00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
PCI0680 Ultra ATA-133 Host Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 100
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-Greg Weeks
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Signature · 11 lines
Clemens Koller _______________________________ R&D Imaging Devices Anagramm GmbH Rupert-Mayer-Str. 45/1 81379 Muenchen Germany http://www.anagramm.de Phone: +49-89-741518-50 Fax: +49-89-741518-19
Switch bank SW1 switch #4 was on which stops config accesses from making it on the bus. It works fine now.
Greg Weeks
Quoted 41 lines · Clemens Koller
Hello, Greg,
I am working on an mpc8540_ads-like board and recently, I ran into data
corruption problems with a Silicon Motion SM501 (Rev AA) PCI graphics card. From my current point of view it seems that Kernel 2.6.11 PCI works well. I am about to check the hardware and signal integrity.BTW: I am working with a Promise Ultra-TX133 IDE controller (PDC20269) which is fine with 66MHz PCICLK.
Greets,
Clemens
Quoted 27 lines
Has anyone else tried to get the PCI bus working on the mpc8560ads board at 2.6.11? The card enumerates, but the I/O resource regions aren't getting set up.
-bash-2.05b# lspci -vv
00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc)
PCI0680 Ultra ATA-133 Host Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=mediumQuoted 1 line
TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 100
Region 0: I/O ports at <unassigned> [disabled] Region 1: I/O ports at <unassigned> [disabled] Region 2: I/O ports at <unassigned> [disabled] Region 3: I/O ports at <unassigned> [disabled] Region 4: I/O ports at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-Greg Weeks
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Greg good to hear, I was about to comment on the fact that PCI based=20 support had been working on the 8540/8560 ADS systems.
- kumar
Quoted 8 lines · Greg Weeks
Switch bank SW1 switch #4 was on which stops config accesses from=20 making
it on the bus. It works fine now.Greg Weeks
Clemens Koller wrote:
Quoted 8 lines
Quoted 3 lines
Hello, Greg,
I am working on an mpc8540_ads-like board and recently, I ran into=20=
data
Quoted 1 line
corruption problems with a Silicon Motion SM501 (Rev AA) PCI=20
graphics
Quoted 1 line
card. =46rom my current point of view it seems that Kernel 2.6.11 =
PCI
Quoted 20 lines
Quoted 3 lines
works well. I am about to check the hardware and signal integrity.
BTW: I am working with a Promise Ultra-TX133 IDE controller=20
(PDC20269)
Quoted 16 lines
which is fine with 66MHz PCICLK.
Greets,
Clemens
Quoted 9 lines
Has anyone else tried to get the PCI bus working on the mpc8560ads board at 2.6.11? The card enumerates, but the I/O resource regions aren't getting set up.
-bash-2.05b# lspci -vv
00:03.0 Unknown mass storage controller: Silicon Image, Inc. (formerly CMD Technology Inc) PCI0680 Ultra ATA-133 Host Controller (rev 02)
=A0=A0=A0=A0=A0=A0=A0 Subsystem: Silicon Image, Inc. (formerly CMD =
Technology Inc)
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
PCI0680 Ultra ATA-133 Host Controller =A0=A0=A0=A0=A0=A0=A0 Control: I/O- Mem- BusMaster- SpecCycle- =
MemWINV- VGASnoop-
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
ParErr- Stepping- SERR- FastB2B-
=A0=A0=A0=A0=A0=A0=A0 Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- =
DEVSEL=3Dmedium
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
TAbort- <TAbort- <MAbort- >SERR- <PERR+
=A0=A0=A0=A0=A0=A0=A0 Interrupt: pin A routed to IRQ 100 =A0=A0=A0=A0=A0=A0=A0 Region 0: I/O ports at <unassigned> =
[disabled]
Quoted 1 line
Quoted 1 line
Quoted 1 line
=A0=A0=A0=A0=A0=A0=A0 Region 1: I/O ports at <unassigned> =
[disabled]
Quoted 1 line
Quoted 1 line
Quoted 1 line
=A0=A0=A0=A0=A0=A0=A0 Region 2: I/O ports at <unassigned> =
[disabled]
Quoted 1 line
Quoted 1 line
Quoted 1 line
=A0=A0=A0=A0=A0=A0=A0 Region 3: I/O ports at <unassigned> =
[disabled]
Quoted 1 line
Quoted 1 line
Quoted 1 line
=A0=A0=A0=A0=A0=A0=A0 Region 4: I/O ports at <unassigned> =
[disabled]
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
=A0=A0=A0=A0=A0=A0=A0 Capabilities: [60] Power Management version 2 =A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0 Flags: PMEClk- DSI+ =
D1+ D2+ AuxCurrent=3D0mA
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
PME(D0-,D1-,D2-,D3hot-,D3cold-)=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0=A0 Status: D0 =
PME-Enable- DSel=3D0 DScale=3D2 PME-
Quoted 13 lines
Quoted 8 lines
Quoted 7 lines
Greg Weeks
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded