Skip to contentSkip to conversation

2.6.11 USB broken on VIA computer (not just ACPI)

DISCUSSION Robert W. Fuller 4 participants 13 messages Mar 16, 2005

lore
Share & tools
lore
#0 lore raw

This isn't limited to the ACPI case. My BIOS is old enough that ACPI is not supported because the kernel can't find RSDP. I found that the USB works if I boot with "noapic." This is probably sub-optimal on an SMP machine. If don't boot with "noapic" I get the following errors:

Mar 15 21:30:17 falcon USB Universal Host Controller Interface driver v2.2
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: irq 19, io base 0xa400
Mar 15 21:30:17 falcon uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
Mar 15 21:30:17 falcon hub 1-0:1.0: USB hub found
Mar 15 21:30:17 falcon hub 1-0:1.0: 2 ports detected
Mar 15 21:30:17 falcon usb 1-2: new low speed USB device using uhci_hcd and address 2
Mar 15 21:30:18 falcon uhci_hcd 0000:00:07.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
Mar 15 21:30:18 falcon usb 1-2: khubd timed out on ep0in
Mar 15 21:30:24 falcon usb 1-2: khubd timed out on ep0out
Mar 15 21:30:29 falcon usb 1-2: khubd timed out on ep0out
Mar 15 21:30:29 falcon usb 1-2: device not accepting address 2, error -110

Here's my lspci:

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+

	Latency: 0
	Region 0: Memory at d0000000 (32-bit, prefetchable)
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- 
FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: e0000000-e1ffffff
	Prefetchable memory behind bridge: d8000000-dfffffff
	Expansion ROM at 00009000 [disabled] [size=4K]
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 23)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 32
	Region 4: I/O ports at a000 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 11) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

0000:00:0f.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-

	Latency: 32 (1000ns min, 4500ns max), cache line size 08
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at a800
	Region 1: I/O ports at ac00 [size=4]
	Region 2: I/O ports at b000 [size=8]
	Region 3: I/O ports at b400 [size=4]
	Region 4: I/O ports at b800 [size=16]
	Region 5: Memory at e3000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [60] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs CT4760 SBLive!
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at bc00
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at c000
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:12.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Avermedia Technologies Inc AVerTV WDM Video Capture
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e3004000 (32-bit, prefetchable)
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:12.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Avermedia Technologies Inc AVerTV WDM Audio Capture
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e3005000 (32-bit, prefetchable)
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:14.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20)
Subsystem: Lite-On Communications Inc LNE100TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 32
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at c400
	Region 1: Memory at e3006000 (32-bit, non-prefetchable) [size=256]

0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R100 QD [Radeon 7200] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon 7000/Radeon
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

	Latency: 32 (2000ns min), cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at d8000000 (32-bit, prefetchable)
	Region 1: I/O ports at 9000 [size=256]
	Region 2: Memory at e1000000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- 
FW- AGP3- Rate=x1,x2,x4
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
#1 lore raw
Quoted 5 lines · Robert W. Fuller

This isn't limited to the ACPI case. My BIOS is old enough that ACPI is
not supported because the kernel can't find RSDP. I found that the USB works if I boot with "noapic." This is probably sub-optimal on an SMP machine. If don't boot with "noapic" I get the following errors:

Did it work OK under previous kernels? If so, which versions?

#2 lore raw

I never actually saw it work until I added the noapic option to the 2.6.11.2 boot. Now I can usually my USB mouse! Of course the downside to specifying noapic is only one CPU is servicing interrupts on my SMP system.

It certainly doesn't work under 2.4.28, but I haven't tried specifying noapic to that kernel. Would that be useful information?

Quoted 7 lines · Andrew Morton
Quoted 1 line · Robert W. Fuller

This isn't limited to the ACPI case. My BIOS is old enough that ACPI is not supported because the kernel can't find RSDP. I found that the USB works if I boot with "noapic." This is probably sub-optimal on an SMP machine. If don't boot with "noapic" I get the following errors:

Did it work OK under previous kernels? If so, which versions?

#3 lore raw
Quoted 5 lines · Robert W. Fuller

I never actually saw it work until I added the noapic option to the 2.6.11.2 boot. Now I can usually my USB mouse! Of course the downside to specifying noapic is only one CPU is servicing interrupts on my SMP system.

Oh, OK. I was just wondering whether this was an actual regression. I guess as it's an old machine and you have a workaround, we have other things to be working on.

It would be nice to fix though.

Quoted 2 lines

It certainly doesn't work under 2.4.28, but I haven't tried specifying noapic to that kernel. Would that be useful information?

Probably not.

#4 lore raw

I suppose you have to have your priorities. It may be old to you, but it's current to me! That used to be the hallmark of Linux, the fact that it would run on lesser hardware.

Of course, I don't know how well video capture is going to work without the apic programming. So I guess I'm reduced to rebooting when I want to switch between USB peripherals and video capture?

Maybe I should have lied and said it worked :-)

Quoted 16 lines · Andrew Morton
Quoted 1 line · Robert W. Fuller

I never actually saw it work until I added the noapic option to the 2.6.11.2 boot. Now I can usually my USB mouse! Of course the downside to specifying noapic is only one CPU is servicing interrupts on my SMP system.

Oh, OK. I was just wondering whether this was an actual regression. I guess as it's an old machine and you have a workaround, we have other things to be working on.

It would be nice to fix though.

Quoted 1 line

It certainly doesn't work under 2.4.28, but I haven't tried specifying noapic to that kernel. Would that be useful information?

Probably not.

#5 lore raw
Quoted 4 lines · Robert W. Fuller

I suppose you have to have your priorities. It may be old to you, but it's current to me! That used to be the hallmark of Linux, the fact that it would run on lesser hardware.

Nobody's going to fix that machine while you persist in top-posting ;)

How old is it, anyway?

Quoted 3 lines

Of course, I don't know how well video capture is going to work without the apic programming. So I guess I'm reduced to rebooting when I want to switch between USB peripherals and video capture?

hm, you didn't mention video capture before. It should work OK?

Are you running the latest BIOS?

You may be able to set the thing up by hand with the help of Documentation/i386/IO-APIC.txt.

#6 lore raw
Quoted 2 lines · Andrew Morton

"Robert W. Fuller" <[email protected]> wrote:
Nobody's going to fix that machine while you persist in top-posting ;)

OK OK. No more top posting. It's Mozilla's fault you know.... It steers you in the wrong direction by leaving a few lines at the top. Yes I'm ashamed to admit I remember when the default behavior of mail clients was to put the cursor at the bottom.

Quoted 1 line

How old is it, anyway?

Hmm. I think I built it in 2000. Wow, time flies when you're having fun!

Quoted 3 lines
Quoted 1 line

Of course, I don't know how well video capture is going to work without the apic programming. So I guess I'm reduced to rebooting when I want to switch between USB peripherals and video capture?

hm, you didn't mention video capture before. It should work OK?

I've only ever used it with the APIC enabled. We'll see what happens without?

Quoted 1 line

Are you running the latest BIOS?

The manufacturer, Tyan, didn't produce more than a handful of BIOS'es within a matter of months after they started producing the board. They haven't released an update since 2000.

Quoted 2 lines

You may be able to set the thing up by hand with the help of Documentation/i386/IO-APIC.txt.

I'll check it out. Thanks!

#10 lore raw

Documentation/i386/IO-APIC.txt (Re: 2.6.11 USB broken on VIA computer (not just ACPI))

In reply to Andrew Morton
Quoted 2 lines · Andrew Morton

You may be able to set the thing up by hand with the help of Documentation/i386/IO-APIC.txt.

There's something I don't get in this document's ascii-art:

8<------------------------------------------------------------------

               ,-.        ,-.        ,-.        ,-.        ,-.
     PIRQ4 ----| |-.    ,-| |-.    ,-| |-.    ,-| |--------| |
               |S|  \  /  |S|  \  /  |S|  \  /  |S|        |S|
     PIRQ3 ----|l|-. `/---|l|-. `/---|l|-. `/---|l|--------|l|
               |o|  \/    |o|  \/    |o|  \/    |o|        |o|
     PIRQ2 ----|t|-./`----|t|-./`----|t|-./`----|t|--------|t|
               |1| /\     |2| /\     |3| /\     |4|        |5|
     PIRQ1 ----| |-  `----| |-  `----| |-  `----| |--------| |
               `-'        `-'        `-'        `-'        `-'

every PCI card emits a PCI IRQ, which can be INTA,INTB,INTC,INTD:

                               ,-.
                         INTD--| |
                               |S|
                         INTC--|l|
                               |o|
                         INTB--|t|
                               |x|
                         INTA--| |
                               `-'

These INTA-D PCI IRQs are always 'local to the card', their real meaning depends on which slot they are in. If you look at the daisy chaining diagram, a card in slot4, issuing INTA IRQ, it will end up as a signal on PIRQ2 of the PCI chipset. [...] 8<------------------------------------------------------------------

If I follow the wire from Slot4's INTA, I'm ending on PIRQ4 whereas the doc says IRQ2. Do I need glasses, or a new fixed-font ?

Xav

#11 lore raw

Re: Documentation/i386/IO-APIC.txt (Re: 2.6.11 USB broken on VIA computer (not just ACPI))

Quoted 29 lines · Xavier Bestel
Quoted 2 lines · Andrew Morton

You may be able to set the thing up by hand with the help of Documentation/i386/IO-APIC.txt.

There's something I don't get in this document's ascii-art:

8<------------------------------------------------------------------

               ,-.        ,-.        ,-.        ,-.        ,-.
     PIRQ4 ----| |-.    ,-| |-.    ,-| |-.    ,-| |--------| |
               |S|  \  /  |S|  \  /  |S|  \  /  |S|        |S|
     PIRQ3 ----|l|-. `/---|l|-. `/---|l|-. `/---|l|--------|l|
               |o|  \/    |o|  \/    |o|  \/    |o|        |o|
     PIRQ2 ----|t|-./`----|t|-./`----|t|-./`----|t|--------|t|
               |1| /\     |2| /\     |3| /\     |4|        |5|
     PIRQ1 ----| |-  `----| |-  `----| |-  `----| |--------| |
               `-'        `-'        `-'        `-'        `-'

every PCI card emits a PCI IRQ, which can be INTA,INTB,INTC,INTD:

                               ,-.
                         INTD--| |
                               |S|
                         INTC--|l|
                               |o|
                         INTB--|t|
                               |x|
                         INTA--| |
                               `-'
Quoted 8 lines

These INTA-D PCI IRQs are always 'local to the card', their real meaning depends on which slot they are in. If you look at the daisy chaining diagram, a card in slot4, issuing INTA IRQ, it will end up as a signal on PIRQ2 of the PCI chipset. [...] 8<------------------------------------------------------------------

If I follow the wire from Slot4's INTA, I'm ending on PIRQ4 whereas the doc says IRQ2. Do I need glasses, or a new fixed-font ?

Sorry for replying to myself, in fact it seems like somebody reversed the order of PIRQ[1-4] and INT[A-D] in the ascii-art, but didn't touch the rest of the text at all. There are several more references to a "reversed order".

Xav

#12 lore raw
In reply to Robert W. Fuller
Quoted 4 lines · Robert W. Fuller

This isn't limited to the ACPI case. My BIOS is old enough that ACPI is not supported because the kernel can't find RSDP. I found that the USB works if I boot with "noapic." This is probably sub-optimal on an SMP machine. If don't boot with "noapic" I get the following errors:

This is a _very_ old bug/issue. The "noapic" boot paramater is the proper fix for such broken hardware.

thanks,

greg k-h

#7 lore raw
In reply to Robert W. Fuller
Quoted 5 lines · Robert W. Fuller
Quoted 1 line

Are you running the latest BIOS?

The manufacturer, Tyan, didn't produce more than a handful of BIOS'es within a matter of months after they started producing the board. They haven't released an update since 2000.

I used to have this motherboard, and Randy Dunlap and I spent a lot of time to try to get this to work properly. Just give up and go by a motherboard that actually has a sane bios, or, buy a USB pci card (less than $20).

Sorry,

greg k-h

#8 lore raw
Quoted 7 lines · Greg KH
Quoted 2 lines · Robert W. Fuller
Quoted 1 line

Are you running the latest BIOS?

The manufacturer, Tyan, didn't produce more than a handful of BIOS'es within a matter of months after they started producing the board. They haven't released an update since 2000.

I used to have this motherboard, and Randy Dunlap and I spent a lot of time to try to get this to work properly. Just give up and go by a motherboard that actually has a sane bios, or, buy a USB pci card (less than $20).

Tempting, but how do I know the new board will work? Shoot, it took me about a year to get everything in this system to work excepting the USB.
Do you have any recommendations for a good Linux SMP motherboard,
preferably for AMD processors?

Quoted 1 line

Sorry,

Thanks for the insight. Now I won't waste too much more time on this.

Regards,

Rob

#9 lore raw
Quoted 11 lines · Robert W. Fuller
Quoted 9 lines · Greg KH
Quoted 4 lines · Robert W. Fuller
Quoted 1 line

Are you running the latest BIOS?

The manufacturer, Tyan, didn't produce more than a handful of BIOS'es within a matter of months after they started producing the board. They haven't released an update since 2000.

I used to have this motherboard, and Randy Dunlap and I spent a lot of time to try to get this to work properly. Just give up and go by a motherboard that actually has a sane bios, or, buy a USB pci card (less than $20).

Quoted 4 lines

Tempting, but how do I know the new board will work? Shoot, it took me about a year to get everything in this system to work excepting the USB.
Do you have any recommendations for a good Linux SMP motherboard,
preferably for AMD processors?

Get a PCI USB card, that's the easiest solution (and cheapest.)

Good luck,

greg k-h