Booting Sarge (24-Mar) on c110
Everything works fine, up til the dreaded STI -switchover. So, it boots, but video isn't initialized right. Let's see: I'm using tty0, with monitor type 3 (1280x1024 Vesa), using graphics3.
Of course, it worked fine with kernel 2.4.x.
Suggestions?
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 13 lines · Matthew Wilcox
Quoted 5 lines · Bryan W. Headley
Everything works fine, up til the dreaded STI -switchover. So, it boots, but video isn't initialized right. Let's see: I'm using tty0, with monitor type 3 (1280x1024 Vesa), using graphics3.
Of course, it worked fine with kernel 2.4.x.
What graphics card are you using?
Watching 2.4.20 boot, it says,
16. U2-IOA BC GSC+ Port (7) at 0xf3fbf000 [8/63], versions 0x501, 0x1, 0xc, add itional addresses: 0xf3f80000
17. U2-IOA BC Runway Port (12) at 0xfff8a000 [10], versions 0x580, 0x7, 0xb
18. Coral SGC Graphics (10) at 0xf4000000 [10/16], versions 0x4, 0x0, 0x77
19. U2-IOA BC GSC+ Port (7) at 0xf3fff000 [10/63], versions 0x501, 0x1, 0xc
And later says, STI device: HPA4071B_LZ
I don't know if this is useful, but the fact that there is nothing in graphics0 .. graphics2 an issue?
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Quoted 28 lines
Quoted 7 lines · Matthew Wilcox
Quoted 4 lines · Bryan W. Headley
Everything works fine, up til the dreaded STI -switchover. So, it boots, but video isn't initialized right. Let's see: I'm using tty0, with monitor type 3 (1280x1024 Vesa), using graphics3.
Quoted 8 lines
Quoted 3 lines
Of course, it worked fine with kernel 2.4.x.
What graphics card are you using?
Watching 2.4.20 boot, it says,
16. U2-IOA BC GSC+ Port (7) at
0xf3fbf000[8/63], versions0x501,0x1,0xc, add
itional addresses:0xf3f80000
17. U2-IOA BC Runway Port (12) at0xfff8a000[10], versions0x580,0x7,0xb
18. Coral SGC Graphics (10) at0xf4000000[10/16], versions0x4,0x0,0x77
19. U2-IOA BC GSC+ Port (7) at0xf3fff000[10/63], versions0x501,0x1,0xc
Quoted 4 lines
And later says, STI device:
HPA4071B_LZI don't know if this is useful, but the fact that there is nothing in graphics0 .. graphics2 an issue?
No, the graphics0 vs. graphics2 thing shouldn't make any difference at all. What kernel is Sarge using - Helge Deller submitted some fixes for Hyperbowl in 2.6 a while back, but I'd have thought they'd have made it into Debian by now.
I sent Helge a Hyperbowl to help him debug (not one with the Z board, just a plain 4071B), but it sounded like he was too busy with other stuff to hack on it right now.
Does the Hyperbowl support double buffering (can't remember off hand) and if so, is it enabled? If its enabled, turn it off - it won't work.
-Andy
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux