Skip to contentSkip to conversation

Orinoco_plx woes on 2.6.13

DISCUSSION Nathan Mahon 2 participants 2 messages Jul 14, 2005 – Jul 15, 2005

lore
Share & tools
lore
#0 lore raw

I use a Belkin F5D6020 wifi card, (version one), and a belkin f5d6000 pci adapter for it. A while ago, it was working flawlessly, though I didn't use it that much after the wife's laptop died.
I've rolled through some kernel upgrades... and it appears my wifi does not work anymore.
here's the technical stuff:

I was still using 2.4 when it was working for sure, but I can't verify that it wasn't ever working on 2.6. under 2.6.11, i noticed the problem, I couldn't bring the interface up.
dmesg produced similar results (to 2.6.13 i have now), but iirc, the
iwconfig didn't make it look like the card was working at all. I rolled
to 2.6.13, and things improved only slightly.

Now, with 2.6.13, I get a successful modprobe orinoco_plx:

Quoted 8 lines
Quoted 8 lines

auron root # dmesg
orinoco_plx 0.15rc2 (Pavel Roskin <[email protected]>, David Gibson <[email protected]>, Daniel Barlow <[email protected]>)
PCI: Found IRQ 9 for device 0000:00:0a.0
orinoco_plx: Detected Orinoco/Prism2 PLX device at 0000:00:0a.0 irq:9, io addr:0x2c00
orinoco_plx: CIS: 01:03:00:00:FF:17:04:67:5A:08:FF:1D:05:01:67:5A:
eth2: Hardware identity 8002:0000:0001:0000

Quoted 10 lines
Quoted 8 lines

eth2: Station identity 001f:0003:0000:0008
eth2: Firmware determined as Intersil 0.8.3
eth2: Ad-hoc demo mode supported
eth2: IEEE standard IBSS ad-hoc mode supported
eth2: WEP supported, 104-bit key
eth2: MAC address 00:30:BD:63:21:11
eth2: Station name "Prism I"
eth2: ready

and at this point, iwconfig looks like the card is behaving somewhat:

Quoted 13 lines
Quoted 11 lines

auron root # iwconfig eth2
eth2 IEEE 802.11b ESSID:"" Nickname:"Prism I"
Mode:Managed Frequency:2.462 GHz Access Point:
00:00:00:00:00:00
Bit Rate:11 Mb/s Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=134/153 Noise level=134/153 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

dmesg hasn't changed at this point.
however, ifconfig breaks it:
auron root # ifconfig eth2 10.5.6.1 netmask 255.255.255.0 broadcast 10.5.6.255

Quoted 3 lines
Quoted 1 line

SIOCSIFFLAGS: No such device

and dmesg now says this:

Quoted 5 lines
Quoted 3 lines

hermes @ 00012c00: Card removed while waiting for command 0x0f38 completion.
eth2: Error -19 configuring card

and if i retry the ifconfig, i get a different error and a different dmesg result:

Quoted 8 lines
Quoted 6 lines

SIOCSIFFLAGS: Connection timed out

eth2: Error -110 setting MAC address
eth2: Error -110 configuring card

Just to state the implied, I'm *not* removing the card, and rmmod'ing the orinico_plx driver and re-modprobing it will produce consistantly the same errors.

Thanks,
Nathan Mahon

System: old amd k6-2 333mhz box with 256mb ram
Distro: gentoo
Kernel config: http://www.vaevictus.net/2.6.13_config.txt
First Post: so flame me if necessary. :D

#1 lore raw

I got a suggestion that i needed to update firmware, along with a suggestion to move to the hostap driver.
for what it's worth, I'm pretty sure hostap won't work for this card. it's listed under orinoco_cs at pcmcia-cs.sf.net, and hostap doesn't like it:

hostap_crypt: registered algorithm 'NULL'
hostap_plx: 0.3.9 - 2005-06-10 (Jouni Malinen <[email protected]>)
PCI: Found IRQ 9 for device 0000:00:0a.0
PLX9052 PCI/PCMCIA adapter: mem=0xdf001000, plx_io=0x2800, irq=9, pccard_io=0x2c00
hostap_plx: CIS: 09 7c f0 00 ff 17 ...
hostap_plx: invalid CIS data
Unknown PC Card CIS - not a Prism2/2.5 card?
hostap_plx: Driver unloaded
hostap_crypt: unregistered algorithm 'NULL' (deinit)

Thanks,
n8

Quoted 146 lines · Nathan Mahon

I use a Belkin F5D6020 wifi card, (version one), and a belkin f5d6000 pci adapter for it. A while ago, it was working flawlessly, though I didn't use it that much after the wife's laptop died.
I've rolled through some kernel upgrades... and it appears my wifi does not work anymore.
here's the technical stuff:

I was still using 2.4 when it was working for sure, but I can't verify that it wasn't ever working on 2.6. under 2.6.11, i noticed the problem, I couldn't bring the interface up.
dmesg produced similar results (to 2.6.13 i have now), but iirc, the
iwconfig didn't make it look like the card was working at all. I rolled
to 2.6.13, and things improved only slightly.

Now, with 2.6.13, I get a successful modprobe orinoco_plx:

Quoted 10 lines
Quoted 10 lines

auron root # dmesg
orinoco_plx 0.15rc2 (Pavel Roskin <[email protected]>, David Gibson <[email protected]>, Daniel Barlow <[email protected]>)
PCI: Found IRQ 9 for device 0000:00:0a.0
orinoco_plx: Detected Orinoco/Prism2 PLX device at 0000:00:0a.0 irq:9, io addr:0x2c00
orinoco_plx: CIS: 01:03:00:00:FF:17:04:67:5A:08:FF:1D:05:01:67:5A:
eth2: Hardware identity 8002:0000:0001:0000
eth2: Station identity 001f:0003:0000:0008
eth2: Firmware determined as Intersil 0.8.3

Quoted 12 lines
Quoted 8 lines

eth2: Ad-hoc demo mode supported
eth2: IEEE standard IBSS ad-hoc mode supported
eth2: WEP supported, 104-bit key
eth2: MAC address 00:30:BD:63:21:11
eth2: Station name "Prism I"
eth2: ready

and at this point, iwconfig looks like the card is behaving somewhat:

Quoted 5 lines
Quoted 5 lines

auron root # iwconfig eth2
eth2 IEEE 802.11b ESSID:"" Nickname:"Prism I"
Mode:Managed Frequency:2.462 GHz Access Point:
00:00:00:00:00:00
Bit Rate:11 Mb/s Sensitivity:1/3

Quoted 12 lines
Quoted 8 lines

Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=134/153 Noise level=134/153 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

dmesg hasn't changed at this point.
however, ifconfig breaks it:
auron root # ifconfig eth2 10.5.6.1 netmask 255.255.255.0 broadcast 10.5.6.255

Quoted 7 lines
Quoted 3 lines

SIOCSIFFLAGS: No such device

and dmesg now says this:

Quoted 9 lines
Quoted 5 lines

hermes @ 00012c00: Card removed while waiting for command 0x0f38 completion.
eth2: Error -19 configuring card

and if i retry the ifconfig, i get a different error and a different dmesg result:

Quoted 10 lines
Quoted 3 lines

SIOCSIFFLAGS: Connection timed out

Quoted 8 lines
Quoted 4 lines

eth2: Error -110 setting MAC address
eth2: Error -110 configuring card

Just to state the implied, I'm *not* removing the card, and rmmod'ing the orinico_plx driver and re-modprobing it will produce consistantly the same errors.

Thanks,
Nathan Mahon

System: old amd k6-2 333mhz box with 256mb ram
Distro: gentoo
Kernel config: http://www.vaevictus.net/2.6.13_config.txt
First Post: so flame me if necessary. :D

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/