PCI card in C160
I am trying to put an Ethernet card into my new (to me) C160 without any success. Any time I put a PCI card in, the machine refused to boot and gives me the message:
*****
***** Disabled the PCI USB card in slot 3.
*****
* * An unsupported PCI I/O configuration has been detected. * * * * Contact your HP service representative for warranty * * * * service to enable the card(s) listed above. * *
I had no trouble with putting a card in my B132L, but it seems to be more forgiving of hardware. It has a 5v PCI bus where the C160 is 3.3v.
I've tried two different Ethernet cards and also a USB card I had lying around - every card I have that was keyed for 3.3v.
I've updated to the latest firmware with no change.
I know this is a little off topic for the list, but it's my guess that not very many other people except Linux users are putting weird hardware in their PARISC workstations.
Anyways, if anyone knows of ethernet cards that will work on a C160 - if you have similar hardware and a success story - I would appreciate hearing about it.
Kurt.
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Quoted 10 lines · Kurt Fitzner
I am trying to put an Ethernet card into my new (to me) C160 without any success. Any time I put a PCI card in, the machine refused to boot and gives me the message:
=20
*****
***** Disabled the PCI USB card in slot 3.
****** * An unsupported PCI I/O configuration has been detected. * * * * Contact your HP service representative for warranty * * * * service to enable the card(s) listed above. * *
Errm, I can't say for sure, but IIRC there was a time when HP thought it is useful to just allow HP certified/supported PCI cards to run in their workstations.
Perhaps someone else can elaborate on that topic?
Quoted 5 lines
I had no trouble with putting a card in my B132L, but it seems to be more forgiving of hardware. It has a 5v PCI bus where the C160 is 3.3v. =20
I've tried two different Ethernet cards and also a USB card I had lying around - every card I have that was keyed for 3.3v.
Well, many cards are universal, ie. keyed for both 3.3v and 5v.
Quoted 9 lines
I've updated to the latest firmware with no change.
=20
I know this is a little off topic for the list, but it's my guess that not very many other people except Linux users are putting weird hardware in their PARISC workstations.
=20
Anyways, if anyone knows of ethernet cards that will work on a C160 - if you have similar hardware and a success story - I would appreciate hearing about it.
I can't speak about C160, but in my C240 I was able to use a DEC tulip and also a Intel EtherExpress PRO 100.
I didn't have so much luck with a noname ne2k and some 3com Vortex, but it was about 3-4 years ago since I last tried ... Anyway I think a DEC Tulip card should be your best bet.
Max
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Quoted 35 lines · Kurt Fitzner
Quoted 10 lines
I am trying to put an Ethernet card into my new (to me) C160 without any success. Any time I put a PCI card in, the machine refused to boot and gives me the message:
*****
***** Disabled the PCI USB card in slot 3.
****** * An unsupported PCI I/O configuration has been detected. * * * * Contact your HP service representative for warranty * * * * service to enable the card(s) listed above. * *Errm, I can't say for sure, but IIRC there was a time when HP thought it is useful to just allow HP certified/supported PCI cards to run in their workstations.
Perhaps someone else can elaborate on that topic?Quoted 5 lines
I had no trouble with putting a card in my B132L, but it seems to be more forgiving of hardware. It has a 5v PCI bus where the C160 is 3.3v.
I've tried two different Ethernet cards and also a USB card I had lying around - every card I have that was keyed for 3.3v.
Well, many cards are universal, ie. keyed for both 3.3v and 5v.
Quoted 9 lines
I've updated to the latest firmware with no change.
I know this is a little off topic for the list, but it's my guess that not very many other people except Linux users are putting weird hardware in their PARISC workstations.
Anyways, if anyone knows of ethernet cards that will work on a C160 - if you have similar hardware and a success story - I would appreciate hearing about it.
Quoted 7 lines
I can't speak about C160, but in my C240 I was able to use a DEC tulip and also a Intel EtherExpress PRO 100.
I didn't have so much luck with a noname ne2k and some 3com Vortex, but it was about 3-4 years ago since I last tried ... Anyway I think a DEC Tulip card should be your best bet.Max
I think HP did this due to bugs in the Dino PCI bridge. Certain revisions have bugs that will quite likely corrupt data on cards that HP haven't certified as working correctly (i.e. HP cards are known not to exercise the bugs). Don't remember off the top of my head exactly which revisions are affected, but if your B132L is actually a B132L+ it could well have a newer, fixed, Dino rev. compared to the C160.
-Andy
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Andy" == Andy Walker <[email protected]> writes:
Andy> I think HP did this due to bugs in the Dino PCI bridge.
Yup.
Andy> Certain revisions have bugs that will quite likely corrupt data Andy> on cards that HP haven't certified as working correctly (i.e. HP Andy> cards are known not to exercise the bugs).
Well. The old rev. Dino does corrupt data (Actually, the HP errata note is funny. It states that Dino will cause corruption but *only* when you do I/O through it. Good thing I/O is not something you do on a regular basis 8).
Anyway. For a graphics card it's not a big deal whether a pixel on the display gets corrupted. And consequently - as far as I remember - the firmware will reject anything but Visualize cards.
The solution is to find a new I/O daughterboard on ebay. There's probably a higher success rate in terms of getting a newer rev. Dino if you get a board from a scrapped C180/C200/C240. Join the exclusive circle of Frankenbox owners!
Signature · 5 lines
Martin K. Petersen http://mkp.net/ _______________________________________________ parisc-linux mailing list [email protected] http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
Quoted 10 lines · Kurt Fitzner
I am trying to put an Ethernet card into my new (to me) C160 without any success. Any time I put a PCI card in, the machine refused to boot and gives me the message:
=20
*****
***** Disabled the PCI USB card in slot 3.
****** * An unsupported PCI I/O configuration has been detected. * * * * Contact your HP service representative for warranty * * * * service to enable the card(s) listed above. * *
BTW, are you really sure you don't have any PCI (UHCI/OHCI/EHCI) USB card installed somewhere? It would be rather strange if it falsly identifies your ethernet card as a USB card ...
Max
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux