Multipath Routing..
Ok folks, here goes..
I have been boggling with a problem for the past week, and still haven't found a solution..
I'm trying to route traffic from two providers through a Linux machine. But that is not the problem. The ISP's have provided me with a WAN IP class for both of the lines, to be routed into a DMZ where the machines a to respond to their respective designated WAN IP on both lines. Every machine on the DMZ has two IP's one on each ISP WAN Class.
I think I'll better draw a map:
WAN1(eth2), WAN2(eth3)
--------- (eth0)
| |-----\ ----------
| DMZ |---\ \ /---| ISP1 |-----
--------- \ \ / ---------- \
\ \ / \
-----------------
| Linux GW/FW | WWW
-----------------
/ \ (eth1) /
--------- / \ ---------- /
| LAN |---/ \---| ISP2 |-----
--------- ----------
NAT(eth4)The DMZ has two WAN IP classes routed from the ISP.
The thing I just can not figure out is how to make the respective WAN IP from the DMZ route out the right ISP link, and the right request from the ISP route into the DMZ.
.. and finally how can I make the LAN able to access it all..
Thanks for your time..
/Daniel Frederiksen
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 30 lines · Daniel Frederiksen
Ok folks, here goes..
I have been boggling with a problem for the past week, and still haven't found a solution..
I'm trying to route traffic from two providers through a Linux machine. But that is not the problem. The ISP's have provided me with a WAN IP class for both of the lines, to be routed into a DMZ where the machines a to respond to their respective designated WAN IP on both lines. Every machine on the DMZ has two IP's one on each ISP WAN Class.
I think I'll better draw a map:
WAN1(eth2), WAN2(eth3) --------- (eth0) | |-----\ ---------- | DMZ |---\ \ /---| ISP1 |----- --------- \ \ / ---------- \ \ \ / \ ----------------- | Linux GW/FW | WWW ----------------- / \ (eth1) / --------- / \ ---------- / | LAN |---/ \---| ISP2 |----- --------- ---------- NAT(eth4)
Quoted 7 lines
The DMZ has two WAN IP classes routed from the ISP.
The thing I just can not figure out is how to make the respective WAN IP from the DMZ route out the right ISP link, and the right request from the ISP route into the DMZ.
.. and finally how can I make the LAN able to access it all..
you need to use ip ru
my ip ru looks like
0: from all lookup local 200: from 141.168.16.16 lookup cable 201: from 220.233.15.63 lookup adsl 32766: from all lookup main 32767: from all lookup default
I created 200 and 201 which means that all traffic that came in on the cable 141.168.16.16 will go out the cable
ip ro sh tab cable
192.168.11.0/24 dev br0 scope link
192.168.10.0/24 dev eth3 scope link
192.168.9.0/24 dev eth4 scope link
default via 141.168.16.1 dev eth0 src 141.168.16.16 metric 30
and the routing tab for the adsl uses the adsl as its default gw.
does that help ?
Quoted 10 lines
Thanks for your time..
/Daniel Frederiksen
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc