Problem with kernel image in a Prep Boot on PowerPC
Hi There!
I have a IBM Power server and I want to put the /boot partition onto
softwrae RAID1 array, but I'm having some problems...
Aparently yaboot boot loader doesn't support /boot partition on a
linux software RAID 1, so i'm trying to put the kernel image (zImage.initrd) directly on the Prep Boot partition. But when the system boots, the kernel can't locate the initrd or the root partition ("Kernel Panic" no init found message).
I think the kernel is pointing to the wrong root partiotion. In a x86
box, I can change the kernel root partition in the boot loader (root= parameter) or using the "rdev" command. In my case, the IBM Power doesn't have a boot loader (yaboot was replaced by the kernel image) and the powerpc64 system doesn't have the rdev command (from util-linux package, the same package on x86 systems have the rdev command!).
Is there a way to change the default root partition in my ppc64
kernel image?
I followed this steps to made the configuration of the kernel image:
# cd /usr/src/linux-2.4 # cp /boot/config-2.4.21-4.EL swinitrd.config Edit the file Makefile to change the EXTRAVERSION variable to match the running kernel: EXTRAVERSION= -4.EL # cp /boot/initrd-2.4.21-4.EL.img /usr/src/linux-2.4/arch/ppc64/boot/ramdisk.image.gz # cd /usr/src/linux-2.4 # make distclean # cp swinitrd.config .config # make oldconfig # make dep # make zImage.initrd # cp /usr/src/linux-2.4/arch/ppc64/boot/zImage.initrd /boot/zImage.initrd-2.4.21-4.EL # cp /usr/src/linux-2.4/swinitrd.config /boot/config.initrd-2.4.21-4.EL # dd if=/boot/zImage.initrd-2.4.21-4.EL of=/dev/sdb1 bs=512
This is my partition scheme:
Disk 1:
/dev/sda1 = Prep Boot Partition (10MB) /dev/sda2 = RAID 1 - "/boot" partition (100MB) /dev/sda3 = swap (300MB) /dev/sda4 = Extendend /dev/sda5 = RAID 1 - "/" root partition (34GB)
Disk 2:
/dev/sdb1 = Prep Boot Partition (10MB) /dev/sdb2 = RAID 1 - "/boot" partition (100MB) /dev/sdb3 = swap (300MB) /dev/sdb4 = Extendend /dev/sdb5 = RAID 1 - "/" root partition (34GB)
Any ideia about this issue?
Thanks a lot!
Márcio.
Quoted 6 lines · Márcio Oliveira
I think the kernel is pointing to the wrong root partiotion. In a x86
box, I can change the kernel root partition in the boot loader (root= parameter) or using the "rdev" command. In my case, the IBM Power doesn't have a boot loader (yaboot was replaced by the kernel image) and the powerpc64 system doesn't have the rdev command (from util-linux package, the same package on x86 systems have the rdev command!).
I don't know anything that will do this on a pre-built kernel. But, you should look at CONFIG_CMDLINE_BOOL and CONFIG_CMDLINE in your kernel configuration. That will let you pre-configure the "root=" command line option.
I don't know if ppc64 can use the zImage-style boot wrapper. If it can, that would provide you with an option of modifying the command line at boot time if needed.
Good luck!
John
Signature · 2 lines
John W. Linville [email protected]
Quoted 9 lines · John W. Linville
Quoted 4 lines · Márcio Oliveira
I think the kernel is pointing to the wrong root partiotion. In a x86
box, I can change the kernel root partition in the boot loader (root= parameter) or using the "rdev" command. In my case, the IBM Power doesn't have a boot loader (yaboot was replaced by the kernel image) and the powerpc64 system doesn't have the rdev command (from util-linux package, the same package on x86 systems have the rdev command!).
Quoted 6 lines
I don't know anything that will do this on a pre-built kernel. But, you should look at
CONFIG_CMDLINE_BOOLandCONFIG_CMDLINEin your kernel configuration. That will let you pre-configure the "root=" command line option.
Hi John,
The command rdev can change the default root partition on x86 linux systems with pre-built kernels.
About the CONFIG_CMDLINE in the kernel configuration, I found it in lots of files in the kernel source tree and I'd like to know which file I need to change this value (/usr/src/linux/arch/ppc64/defconfig ?).
Quoted 5 lines
I don't know if ppc64 can use the zImage-style boot wrapper. If it can, that would provide you with an option of modifying the command line at boot time if needed.
According to this doc: http://www-128.ibm.com/developerworks/eserver/library/es-SW_RAID_LINUX.html, ppc64 can use zImage-style boot wrapper, so I'm trying it.
Quoted 5 lines
Good luck!
John
Thanks John!
Márcio.
Quoted 2 lines · Márcio Oliveira
The command rdev can change the default root partition on x86 linux systems with pre-built kernels.
Of course...I meant I don't know of anything like that for PPC.
Quoted 3 lines
About the
CONFIG_CMDLINEin the kernel configuration, I found it in lots of files in the kernel source tree and I'd like to know which file I need to change this value (/usr/src/linux/arch/ppc64/defconfig?).
Probably just in your .config file:
cp arch/ppc64/defconfig .config
vi .config # Change CONFIG_CMDLINE here
make oldconfig
Quoted 3 lines
According to this doc:
http://www-128.ibm.com/developerworks/eserver/library/es-SW_RAID_LINUX.html,
ppc64 can use zImage-style boot wrapper, so I'm trying it.
Cool...I think you will like having that as an option.
John
Signature · 2 lines
John W. Linville [email protected]