Skip to contentSkip to conversation

Problem with cpufreq on Geode GX1

DISCUSSION Jose Miguel Goncalves 2 participants 3 messages Aug 26, 2005 – Aug 29, 2005

lore
Share & tools
lore
#0 lore raw

Hi all,

I'm trying to use cpufreq on my Geode GX1 board with linux-2.6.12.5, but, while everything seems OK, i.e., I can change from performance to powersave governor and back and /proc/cpuinfo reports me frequency changes, I can get no effective frequency/CPU power change because I check it with the Whetstone benchmark and it allways give me the same value (~100 MWIPS). Any ideas from were could be the problem?

Some additional info follows:

$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor

performance

$ cat /proc/cpuinfo

processor : 0
vendor_id : CyrixInstead
cpu family : 5
model : 9
model name : Geode(TM) Integrated Processor by National Semi
stepping : 2
cpu MHz : 300.672
cache size : 16 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu tsc msr cx8 cmov mmx cxmmx
bogomips : 591.87

$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /proc/cpuinfo

processor : 0
vendor_id : CyrixInstead
cpu family : 5
model : 9
model name : Geode(TM) Integrated Processor by National Semi
stepping : 2
cpu MHz : 37.095
cache size : 16 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu tsc msr cx8 cmov mmx cxmmx
bogomips : 73.02

Best regards,
Jose Goncalves

#1 lore raw

Hi,

I will check code in several days, but I cannot re-produce a problem in a moment because I am away from home for business trip.

In my understand, the driver recognize the CPU properly.

At Fri, 26 Aug 2005 19:01:37 +0100,

Quoted 9 lines · Jose Miguel Goncalves

Hi all,

I'm trying to use cpufreq on my Geode GX1 board with linux-2.6.12.5, but, while everything seems OK, i.e., I can change from performance to powersave governor and back and /proc/cpuinfo reports me frequency changes, I can get no effective frequency/CPU power change because I check it with the Whetstone benchmark and it allways give me the same value (~100 MWIPS). Any ideas from were could be the problem?

Can you try to check also follows?

/sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq

With this driver, it will significantly slow down by setting powersave mode. It seems some bus in the driver.

Thank you for report.

Hiroshi

Signature · 5 lines
Hiroshi Miura  --- [email protected], Mobile --- [email protected]
NTTDATA Corp. OpenSource Software Center. --- [email protected] 
NTTDATA Intellilink Corp. OpenSource Engineering Dev. -- [email protected]
Kobe Institute of Computing Graduate School of IT - Lecturer -- [email protected]
Key id=04AB8617 fingerprint=9117 9407 5684 FBF1 4063  15B4 401D D077 04AB 8617
#2 lore raw

Hi Hiroshi,

Here goes the extra info that you asked for:

$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
300759
$ cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
300759
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
23042
$ cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
23042

One other strange thing that I've noticed is that I'll never get the same frequency when switching to powersave govenor. It allways gets increased a little bit. For example:

$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
24453
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
27779
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
29947
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
32400

Thanks for checking this.

Jose Goncalves

Quoted 32 lines · Hiroshi Miura

Hi,

I will check code in several days, but I cannot re-produce a problem in a moment because I am away from home for business trip.

In my understand, the driver recognize the CPU properly.

At Fri, 26 Aug 2005 19:01:37 +0100,

Quoted 8 lines · Jose Miguel Goncalves

Hi all,

I'm trying to use cpufreq on my Geode GX1 board with linux-2.6.12.5, but, while everything seems OK, i.e., I can change from performance to powersave governor and back and /proc/cpuinfo reports me frequency changes, I can get no effective frequency/CPU power change because I check it with the Whetstone benchmark and it allways give me the same value (~100 MWIPS). Any ideas from were could be the problem?

Can you try to check also follows?

/sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq

With this driver, it will significantly slow down by setting powersave mode. It seems some bus in the driver.

Thank you for report.

Hiroshi